166 lines
3.2 KiB
INI
166 lines
3.2 KiB
INI
# This file contains pin mappings for the Creality CR-30 PrintMill. To
|
|
# use this config, during "make menuconfig" select the STM32F103 with
|
|
# a "28KiB bootloader" and serial (on USART1 PA10/PA9) communication.
|
|
|
|
# If you prefer a direct serial connection, in "make menuconfig"
|
|
# select "Enable extra low-level configuration options" and select
|
|
# serial (on USART3 PB11/PB10), which is broken out on the 10 pin IDC
|
|
# cable used for the LCD module as follows:
|
|
# 3: Tx, 4: Rx, 9: GND, 10: VCC
|
|
|
|
# Flash this firmware by copying "out/klipper.bin" to a SD card and
|
|
# turning on the printer with the card inserted. The firmware
|
|
# filename must end in ".bin" and must not match the last filename
|
|
# that was flashed.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PC2
|
|
dir_pin: !PB9
|
|
enable_pin: !PC3
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^!PA3
|
|
position_endstop: 0
|
|
position_max: 220
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: PB8
|
|
dir_pin: !PB7
|
|
enable_pin: !PC3
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^!PA7
|
|
position_endstop: 0
|
|
position_max: 240
|
|
|
|
[stepper_z]
|
|
step_pin: PB6
|
|
dir_pin: !PB5
|
|
enable_pin: !PC3
|
|
microsteps: 16
|
|
rotation_distance: 2.75
|
|
endstop_pin: ^!PA5
|
|
position_endstop: 0.0
|
|
position_max: 20000000
|
|
|
|
[extruder]
|
|
step_pin: PB4
|
|
dir_pin: !PB3
|
|
enable_pin: !PC3
|
|
microsteps: 16
|
|
rotation_distance: 23.0
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PA0
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC5
|
|
control: pid
|
|
pid_Kp: 21.527
|
|
pid_Ki: 1.063
|
|
pid_Kd: 108.982
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
[filament_switch_sensor spool]
|
|
pause_on_runout: True
|
|
switch_pin: ^!PA6
|
|
|
|
[heater_bed]
|
|
heater_pin: PA1
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC4
|
|
control: pid
|
|
pid_Kp: 54.027
|
|
pid_Ki: 0.770
|
|
pid_Kd: 948.182
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
# K-FAN1
|
|
[fan]
|
|
pin: PA2
|
|
|
|
# K-FAN2
|
|
[fan_generic k_fan2]
|
|
pin: PC0
|
|
|
|
# K-FAN3
|
|
[fan_generic k_fan3]
|
|
pin: PC1
|
|
|
|
[temperature_sensor mcu_temp]
|
|
sensor_type: temperature_mcu
|
|
min_temp: 0
|
|
max_temp: 100
|
|
|
|
[output_pin led]
|
|
pin: PC14
|
|
|
|
# Neopixel LED support
|
|
# [neopixel led_neopixel]
|
|
# pin: PC14
|
|
|
|
# BL-touch
|
|
# [bltouch]
|
|
# control_pin: PB0
|
|
# sensor_pin: PB1
|
|
|
|
# TMC Uart Mod Pins:
|
|
# https://github.com/adelyser/Marlin-CR30/wiki
|
|
# [tmc2208 stepper_x]
|
|
# uart_pin: PB0
|
|
#
|
|
# [tmc2208 stepper_y]
|
|
# uart_pin: PB1
|
|
#
|
|
# [tmc2208 stepper_z]
|
|
# uart_pin: PA13
|
|
#
|
|
# [tmc2208 extruder]
|
|
# uart_pin: PA14
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
|
restart_method: command
|
|
|
|
[display]
|
|
lcd_type: st7920
|
|
cs_pin: PB12
|
|
sclk_pin: PB13
|
|
sid_pin: PB15
|
|
encoder_pins: ^PB14, ^PB10
|
|
click_pin: ^!PB2
|
|
|
|
[output_pin beeper]
|
|
pin: PC6
|
|
|
|
[printer]
|
|
kinematics: corexy
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
# Override to support unlimited belt size
|
|
# (homing Z simply resets its virtual position to 0.0)
|
|
[homing_override]
|
|
axes: z
|
|
set_position_z: 0
|
|
gcode:
|
|
{% if params.X is not defined and params.Y is not defined and params.Z is not defined %}G28 X0 Y0{% endif %}
|
|
{% if params.X is defined %}G28 X0{% endif %}
|
|
{% if params.Y is defined %}G28 Y0{% endif %}
|
|
G92 Z0
|
|
|
|
# Eject all printed parts from the belt
|
|
[gcode_macro BED_EJECT]
|
|
gcode:
|
|
TURN_OFF_HEATERS
|
|
G28 ; Re-home
|
|
G1 X50 Y50 ; Move hotend out of the way of the belt
|
|
G1 Z420 F4000 ; Unload belt
|
|
G28 Z0 ; Re-home Z
|