81 lines
2.8 KiB
Markdown
81 lines
2.8 KiB
Markdown
There are several features still to be implemented in Klipper. In no
|
|
particular order:
|
|
|
|
Host user interaction
|
|
=====================
|
|
|
|
* See if there is a better way to report errors. Octoprint sometimes
|
|
doesn't highlight an error (one has to look in the terminal tab to
|
|
find the error) and errors written to the log can be non-obvious to
|
|
a user.
|
|
|
|
* Improve gcode interface:
|
|
|
|
* Provide a way to temporarily disable endstop checks so that a user
|
|
can issue commands that potentially move the head past
|
|
position_min/position_max.
|
|
|
|
* Improve logging:
|
|
|
|
* Possibly collate and report the statistics messages in the log in a
|
|
more friendly way.
|
|
|
|
* Possibly support a mechanism for the host to limit maximum velocity
|
|
so that the mcu is never requested to step at a higher rate than it
|
|
can support.
|
|
|
|
Safety features
|
|
===============
|
|
|
|
* Support loading a valid step range into the micro-controller
|
|
software after homing. This would provide a sanity check in the
|
|
micro-controller that would reduce the risk of the host commanding a
|
|
stepper motor past its valid step range. To maintain high
|
|
efficiency, the micro-controller would only need to check
|
|
periodically (eg, every 100ms) that the stepper is in range.
|
|
|
|
* Possibly support periodically querying the endstop switches and use
|
|
multiple step ranges depending on the switch state. This would
|
|
enable runtime endstop detection. (However, it's unclear if runtime
|
|
endstop detection is a good idea because of spurious signals caused
|
|
by electrical noise.)
|
|
|
|
Testing features
|
|
================
|
|
|
|
* Complete the host based simulator. It's possible to compile the
|
|
micro-controller for a "host simulator", but that simulator doesn't
|
|
do anything currently. It would be useful to expand the code to
|
|
support more error checks, kinematic simulations, and improved
|
|
logging.
|
|
|
|
Documentation
|
|
=============
|
|
|
|
* Add documentation describing how to perform bed-leveling accurately
|
|
in Klipper. Improve description of stepper phase based bed leveling.
|
|
|
|
Hardware features
|
|
=================
|
|
|
|
* Port to additional micro-controller architectures:
|
|
* Smoothieboard / NXP LPC1769 (ARM cortex-M3)
|
|
|
|
* Support for additional kinematics: scara, etc.
|
|
|
|
* Possible support for touch panels attached to the micro-controller.
|
|
(In general, it would be preferable to attach touch panels to the
|
|
host system and have octoprint interact with the panel directly, but
|
|
it would also be useful to handle panels already hardwired to the
|
|
micro-controller.)
|
|
|
|
Misc features
|
|
=============
|
|
|
|
* Possibly support a "feed forward PID" that takes into account the
|
|
amount of plastic being extruded. If the extrude rate changes
|
|
significantly during a print it can cause heating bumps that the PID
|
|
overcompensates for. The temperature change due to the extrusion
|
|
rate could be modeled to eliminate these bumps and make the
|
|
extrusion temperature more consistent.
|