3diy
/
klipper
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
klipper/klippy/extras
History
Kevin O'Connor 2b8dca5dbf probe: Move multi-sampling capability from ProbePointsHelper to Probe 
This changes the config file so that the configuration of
multi-samples is now done in the [probe] (and [bltouch]) section
instead of the various delta, bed_mesh, z_tilt, etc. config sections.

With this change, PROBE and PROBE_CALIBRATE commands now also utilize
multi-sampling.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 		2019-06-06 10:08:58 -04:00
..
display menu: Remove customized get_status overrides 2019-06-04 11:55:40 -04:00
__init__.py
…
ad5206.py ad5206: Use bus.py helper code for spi 2018-11-21 12:12:31 -05:00
adc_temperature.py adc_temperature: Minor comment update 2019-06-02 17:12:55 -04:00
bed_mesh.py probe: ProbePointsHelper adjustable minimum points 2019-05-21 14:17:09 -04:00
bed_screws.py bed_screws: Be sure to call gcode.reset_last_position() after any manual move 2019-06-03 13:43:49 -04:00
bed_tilt.py probe: ProbePointsHelper adjustable minimum points 2019-05-21 14:17:09 -04:00
bltouch.py bltouch: Update command timing 2019-05-26 11:09:32 -04:00
bus.py bus: Don't reserve any pins if BUS_PINS_x is not defined 2019-04-07 20:43:23 -04:00
buttons.py buttons: Minor code movement 2019-05-26 00:18:48 -04:00
controller_fan.py controller_fan: Allow multiple controller_fan sections to be defined 2019-03-10 13:57:01 -04:00
delta_calibrate.py probe: ProbePointsHelper adjustable minimum points 2019-05-21 14:17:09 -04:00
endstop_phase.py tmc2660: Add endstop phase detection functionality to TMC2660 extra (#816) 2018-10-24 16:01:12 -04:00
fan.py Wrap code to 80 columns 2019-02-27 13:27:52 -05:00
filament_switch_sensor.py filament_switch_sensor: initial implementation of switch based filament runout/insert sensor 2019-03-01 00:45:51 -05:00
firmware_retraction.py firmware_retraction: Implementation of tuneable G10/G11 firmware retraction (#1617) 2019-06-06 09:10:09 -04:00
force_move.py force_move: Avoid divide by zero in move time calculation 2019-03-31 09:00:23 -04:00
gcode_macro.py gcode_macro: Add support "x in printer" to templates 2019-06-04 12:41:28 -04:00
heater_bed.py heater_bed: Wrap lines to 80 columns 2019-02-26 11:20:01 -05:00
heater_fan.py heater_fan: add get_status method 2019-06-04 11:43:34 -04:00
heater_generic.py heater: Support generic gcode_id registration for sensors 2019-02-26 12:07:00 -05:00
homing_override.py homing_override: Use gcode_macro style templates on gcode 2019-04-04 18:35:23 -04:00
idle_timeout.py idle_timeout: Add a get_status() method 2019-06-04 12:35:50 -04:00
manual_probe.py manual_probe: Verify no XY moves since start of manual probe 2019-05-31 10:24:52 -04:00
manual_stepper.py manual_stepper: Add support for moves with acceleration 2019-03-03 13:38:10 -05:00
mcp4018.py mcp4018: Add initial support for the mcp4018 digipot 2019-02-16 08:16:37 -05:00
mcp4451.py i2ccmds: Pass the i2c address as a 7-bit number (0-127) 2019-01-07 20:00:44 -05:00
mcp4728.py mcp4728: Add initial support for the mcp4728 i2c dac chip 2019-01-02 18:17:56 -05:00
multi_pin.py pins: Explicitly pass can_invert and can_pullup to lookup_pin() 2018-07-26 09:44:45 -04:00
output_pin.py output_pin: add get_status method 2019-06-04 11:44:35 -04:00
pause_resume.py pause_resume: Use Octoprint's "paused" and "resumed" action commands. 2019-06-02 19:19:32 -04:00
pid_calibrate.py pid_calibrate: Add some comments on the calibration methodology 2018-10-19 22:40:11 -04:00
probe.py probe: Move multi-sampling capability from ProbePointsHelper to Probe 2019-06-06 10:08:58 -04:00
quad_gantry_level.py quad_gantry_level: Require exactly 4 probe points 2019-05-21 14:17:09 -04:00
query_endstops.py query_endstops: Move QUERY_ENDSTOP command to it own extras/ module 2018-07-16 10:06:30 -04:00
replicape.py replicape: add support for Linux hardware PWM (#1443) 2019-04-06 13:51:51 -04:00
respond.py respond: Wrap code to 80 columns 2019-02-27 14:33:17 -05:00
samd_sercom.py atsamd: Use enumerations for buses and reserve pins 2019-04-04 18:29:31 -04:00
screws_tilt_adjust.py probe: ProbePointsHelper adjustable minimum points 2019-05-21 14:17:09 -04:00
servo.py servo: add get_status method 2019-06-04 11:44:50 -04:00
spi_temperature.py spi_temperature: MAX6675 and MAX31855 should use spi mode 0 2019-05-22 11:40:53 -04:00
static_digital_output.py static_digital_output: Add static_digital_output section to extras/ 2018-03-17 13:06:51 -04:00
statistics.py klippy: Convert printer_state("ready") to an event handler 2019-01-08 10:59:43 -05:00
sx1509.py sx1509: Convert code to use generic i2c bus support 2019-04-04 18:29:30 -04:00
temperature_fan.py temperature_fan: Add gcode command for temperature_fan.py (#1520) 2019-04-15 21:13:29 -04:00
temperature_sensor.py temperature_sensor: Add generic temperature sensor support 2019-02-26 13:15:56 -05:00
thermistor.py thermistor: Add support for printers with an "inline_resistor" 2019-06-02 10:59:23 -04:00
tmc2130.py tmc2130: Check field name validity. (#1697) 2019-06-02 11:41:15 -04:00
tmc2208.py tmc2130: Check field name validity. (#1697) 2019-06-02 11:41:15 -04:00
tmc2660.py tmc2130: Check field name validity. (#1697) 2019-06-02 11:41:15 -04:00
tmc5160.py tmc2130: Check field name validity. (#1697) 2019-06-02 11:41:15 -04:00
tsl1401cl_filament_width_sensor.py tsl1401cl_filament_width_sensor: Fix incorrect math in filament width sensor. (#1541) 2019-04-15 21:11:26 -04:00
verify_heater.py verify_heater: If the heating_gain check fails, just use max_error check 2019-03-08 10:55:46 -05:00
virtual_sdcard.py virtual_sdcard: consistent sorting (#1387) 2019-04-14 11:34:22 -04:00
z_tilt.py z_tilt: minimum points 2 2019-05-21 14:17:09 -04:00