160 lines
2.8 KiB
INI
160 lines
2.8 KiB
INI
# This file contains common pin mappings for the GTM32 PRO board in
|
|
# the Geeetech 301 printer. To use this config, the firmware should be
|
|
# compiled for the STM32F103 with "No bootloader", serial (on USART1
|
|
# PA10/PA9) communication and GPIO pins to set at micro-controller
|
|
# startup set to "!PB4,!PB5,!PB0,!PB1"
|
|
|
|
# The "make flash" command does not work on the Geeetech 301. Instead,
|
|
# after running "make", run the following command to flash the board:
|
|
# stm32flash -w out/klipper.bin -v -i rts,-dtr,dtr -b 115200 /dev/ttyUSB0
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[multi_pin heater]
|
|
pins: PB4,PB5,PB0
|
|
|
|
[multi_pin extruder_fans]
|
|
pins: PB7,PB8,PB9
|
|
|
|
[thermistor bed_thermistor]
|
|
temperature1: 24
|
|
resistance1: 104600
|
|
temperature2: 40
|
|
resistance2: 47700
|
|
temperature3: 67
|
|
resistance3: 13000
|
|
|
|
[stepper_a]
|
|
step_pin: PC6
|
|
dir_pin: PD13
|
|
enable_pin: !PA8
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^PE4
|
|
homing_speed: 50
|
|
position_endstop: 216
|
|
arm_length: 201
|
|
|
|
[stepper_b]
|
|
step_pin: PA12
|
|
dir_pin: PA11
|
|
enable_pin: !PA15
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^PE2
|
|
|
|
[stepper_c]
|
|
step_pin: PD6
|
|
dir_pin: PD3
|
|
enable_pin: !PB3
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^PE0
|
|
|
|
[extruder]
|
|
step_pin: PC14
|
|
dir_pin: !PC13
|
|
enable_pin: !PC15
|
|
microsteps: 16
|
|
rotation_distance: 32
|
|
nozzle_diameter: 0.4
|
|
filament_diameter: 1.75
|
|
heater_pin: multi_pin:heater
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
pullup_resistor: 4700
|
|
inline_resistor: 220
|
|
sensor_pin: PC0
|
|
min_temp: 0
|
|
max_temp: 250
|
|
control: pid
|
|
pid_Kp: 39
|
|
pid_Ki: 2
|
|
pid_Kd: 210
|
|
|
|
[extruder1]
|
|
step_pin: PA0
|
|
dir_pin: !PB6
|
|
enable_pin: !PA1
|
|
microsteps: 16
|
|
rotation_distance: 32
|
|
nozzle_diameter: 0.4
|
|
filament_diameter: 1.75
|
|
shared_heater: extruder
|
|
|
|
[extruder2]
|
|
step_pin: PB2
|
|
dir_pin: !PB11
|
|
enable_pin: !PC4
|
|
microsteps: 16
|
|
rotation_distance: 32
|
|
nozzle_diameter: 0.4
|
|
filament_diameter: 1.75
|
|
shared_heater: extruder
|
|
|
|
[heater_bed]
|
|
heater_pin: PB1
|
|
sensor_type: bed_thermistor
|
|
sensor_pin: PC3
|
|
min_temp: 0
|
|
max_temp: 150
|
|
control: pid
|
|
pid_Kp: 67
|
|
pid_Ki: 4
|
|
pid_Kd: 310
|
|
|
|
[temperature_sensor board]
|
|
sensor_type: temperature_mcu
|
|
gcode_id: MCU
|
|
|
|
[temperature_sensor secondary]
|
|
sensor_pin: PC1
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
pullup_resistor: 4700
|
|
inline_resistor: 220
|
|
gcode_id: SEC
|
|
|
|
[temperature_sensor ambient]
|
|
sensor_pin: PC2
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
pullup_resistor: 4700
|
|
inline_resistor: 220
|
|
gcode_id: AMB
|
|
|
|
[homing_heaters]
|
|
heaters: extruder
|
|
|
|
[heater_fan extruder]
|
|
pin: multi_pin:extruder_fans
|
|
heater: extruder
|
|
max_power: 0.8
|
|
off_below: 0.2
|
|
shutdown_speed: 0
|
|
|
|
[mcu]
|
|
serial: /dev/ttyUSB0
|
|
restart_method: cheetah
|
|
|
|
[printer]
|
|
kinematics: delta
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 150
|
|
delta_radius: 94
|
|
|
|
[output_pin beep]
|
|
pin: PB10
|
|
|
|
[output_pin lcd_beep]
|
|
pin: PE12
|
|
|
|
[display]
|
|
lcd_type: hd44780
|
|
rs_pin: PE6
|
|
e_pin: PE14
|
|
d4_pin: PD8
|
|
d5_pin: PD9
|
|
d6_pin: PD10
|
|
d7_pin: PE15
|
|
encoder_pins: ^PE9,^PE8
|
|
click_pin: ^PE13
|