200 lines
3.4 KiB
INI
200 lines
3.4 KiB
INI
# This file contains common pin mappings for the BIGTREETECH Manta M5P
|
|
# To use this config, the firmware should be compiled for the
|
|
# STM32G0B1 with a "8KiB bootloader" "8 MHz crystal"
|
|
# and "USB (on PA11/PA12)" or "CAN bus (on PD0/PD1)".
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PC8
|
|
dir_pin: !PC9
|
|
enable_pin: !PA15
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^PD3
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: PA10
|
|
dir_pin: !PA14
|
|
enable_pin: !PA13
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^PD2
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: PC6
|
|
dir_pin: PC7
|
|
enable_pin: !PA9
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: ^PC3
|
|
position_endstop: 0.0
|
|
position_max: 200
|
|
|
|
[extruder]
|
|
step_pin: PB12
|
|
dir_pin: !PB11
|
|
enable_pin: !PA8
|
|
microsteps: 16
|
|
rotation_distance: 33.500
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PC5
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PA1
|
|
control: pid
|
|
pid_Kp: 21.527
|
|
pid_Ki: 1.063
|
|
pid_Kd: 108.982
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
#sensor_type:MAX31865
|
|
#sensor_pin: PA4
|
|
#spi_bus: spi1
|
|
#rtd_nominal_r: 100
|
|
#rtd_reference_r: 430
|
|
#rtd_num_of_wires: 2
|
|
|
|
#[filament_switch_sensor material_0]
|
|
#switch_pin: PC2
|
|
|
|
#[extruder1]
|
|
#step_pin: PB0
|
|
#dir_pin: PB1
|
|
#enable_pin: !PC4
|
|
#heater_pin: PA7
|
|
#sensor_pin: PA2
|
|
#...
|
|
|
|
[heater_bed]
|
|
heater_pin: PA5
|
|
sensor_type: Generic 3950
|
|
sensor_pin: PA0
|
|
control: watermark
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[fan]
|
|
pin: PA4
|
|
|
|
#[heater_fan fan1]
|
|
#pin: PA3
|
|
|
|
#[heater_fan SoC_fan]
|
|
#pin: CB1:gpio79
|
|
#pin: RPI:gpio26
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
########################################
|
|
# TMC2209 configuration
|
|
########################################
|
|
|
|
#[tmc2209 stepper_x]
|
|
#uart_pin: PD9
|
|
#run_current: 0.800
|
|
#diag_pin: PD3
|
|
|
|
#[tmc2209 stepper_y]
|
|
#uart_pin: PD8
|
|
#run_current: 0.800
|
|
#diag_pin: PD2
|
|
|
|
#[tmc2209 stepper_z]
|
|
#uart_pin: PB10
|
|
#run_current: 0.800
|
|
#diag_pin: PC3
|
|
|
|
#[tmc2209 extruder]
|
|
#uart_pin: PB2
|
|
#run_current: 0.600
|
|
#diag_pin: PC2
|
|
|
|
#[tmc2209 extruder1]
|
|
#uart_pin: PA6
|
|
#run_current: 0.600
|
|
#diag_pin:
|
|
|
|
########################################
|
|
# TMC2130 configuration
|
|
########################################
|
|
|
|
#[tmc2130 stepper_x]
|
|
#cs_pin: PD9
|
|
#spi_bus: spi2
|
|
#run_current: 0.800
|
|
#stealthchop_threshold: 999999
|
|
#diag1_pin: PD3
|
|
|
|
#[tmc2130 stepper_y]
|
|
#cs_pin: PD8
|
|
#spi_bus: spi2
|
|
#run_current: 0.800
|
|
#stealthchop_threshold: 999999
|
|
#diag1_pin: PD2
|
|
|
|
#[tmc2130 stepper_z]
|
|
#cs_pin: PB10
|
|
#spi_bus: spi2
|
|
#run_current: 0.650
|
|
#stealthchop_threshold: 999999
|
|
#diag1_pin: PC3
|
|
|
|
#[tmc2130 extruder]
|
|
#cs_pin: PB2
|
|
#spi_bus: spi2
|
|
#run_current: 0.800
|
|
#stealthchop_threshold: 999999
|
|
#diag1_pin: PC2
|
|
|
|
#[tmc2130 extruder1]
|
|
#cs_pin: PA6
|
|
#spi_bus: spi2
|
|
#run_current: 0.800
|
|
#stealthchop_threshold: 999999
|
|
#diag1_pin:
|
|
|
|
[board_pins]
|
|
aliases:
|
|
# EXP1 header
|
|
EXP1_1=PD5, EXP1_3=PB3, EXP1_5=PB5, EXP1_7=PB7, EXP1_9=<GND>,
|
|
EXP1_2=PD4, EXP1_4=PD6, EXP1_6=PB4, EXP1_8=PB6, EXP1_10=<5V>,
|
|
# EXP2 header
|
|
EXP2_1=PB14, EXP2_3=PB8, EXP2_5=PC10, EXP2_7=PC12, EXP2_9=<GND>,
|
|
EXP2_2=PB13, EXP2_4=PB9, EXP2_6=PB15, EXP2_8=<RST>, EXP2_10=<NC>
|
|
|
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
|
|
|
#[bltouch]
|
|
#sensor_pin: PC13
|
|
#control_pin: PC15
|
|
|
|
# Proximity switch
|
|
#[probe]
|
|
#pin: PC15
|
|
|
|
#[neopixel my_neopixel1]
|
|
#pin: PC11
|
|
|
|
#[neopixel my_neopixel2]
|
|
#pin: PC14
|
|
|
|
#[adxl345]
|
|
#cs_pin: PC0
|
|
#spi_bus: spi2
|