309 lines
13 KiB
INI
309 lines
13 KiB
INI
# This file serves as documentation for config parameters of
|
|
# additional devices that may be configured on a printer. The snippets
|
|
# in this file may be copied into the main printer.cfg file. See the
|
|
# "example.cfg" file for description of common config parameters.
|
|
#
|
|
# Note, where an extra config section creates additional pins, the
|
|
# section defining the pins must be listed in the config file before
|
|
# any sections using those pins.
|
|
|
|
|
|
# Z height probe. One may define this section to enable Z height
|
|
# probing hardware. When this section is enabled, PROBE and
|
|
# QUERY_PROBE extended g-code commands become available. The probe
|
|
# section also creates a virtual probe:z_virtual_endstop pin. One may
|
|
# set the stepper_z endstop_pin to this virtual pin on cartesian style
|
|
# printers that use the probe in place of a z endstop.
|
|
#[probe]
|
|
#pin: ar15
|
|
# Probe detection pin. This parameter must be provided.
|
|
#speed: 5.0
|
|
# Speed (in mm/s) of the Z axis when probing. The default is 5mm/s.
|
|
#z_position: 0.0
|
|
# The Z position to command the head to move to during a PROBE
|
|
# command. The default is 0.
|
|
#activate_gcode:
|
|
# A list of G-Code commands (one per line) to execute prior to each
|
|
# probe attempt. This may be useful if the probe needs to be
|
|
# activated in some way. The default is to not run any special
|
|
# G-Code commands on activation.
|
|
#deactivate_gcode:
|
|
# A list of G-Code commands (one per line) to execute after each
|
|
# probe attempt completes. The default is to not run any special
|
|
# G-Code commands on deactivation.
|
|
|
|
|
|
# Bed tilt compensation. One may define a [bed_tilt] config section to
|
|
# enable move transformations that account for a tilted bed.
|
|
#[bed_tilt]
|
|
#x_adjust: 0
|
|
# The amount to add to each move's Z height for each mm on the X
|
|
# axis. The default is 0.
|
|
#y_adjust: 0
|
|
# The amount to add to each move's Z height for each mm on the Y
|
|
# axis. The default is 0.
|
|
# The remaining parameters control a BED_TILT_CALIBRATE extended
|
|
# g-code command that may be used to calibrate appropriate x and y
|
|
# adjustment parameters.
|
|
#points:
|
|
# A newline separated list of X,Y points that should be probed
|
|
# during a BED_TILT_CALIBRATE command. The default is to not enable
|
|
# the command.
|
|
#speed: 50
|
|
# The speed (in mm/s) of non-probing moves during the
|
|
# calibration. The default is 50.
|
|
#horizontal_move_z: 5
|
|
# The height (in mm) that the head should be commanded to move to
|
|
# just prior to starting a probe operation. The default is 5.
|
|
#probe_z_offset: 0
|
|
# The Z height (in mm) of the head when the probe triggers. The
|
|
# default is 0.
|
|
#manual_probe:
|
|
# If true, then BED_TILT_CALIBRATE will perform manual probing. If
|
|
# false, then a PROBE command will be run at each probe
|
|
# point. Manual probing is accomplished by manually jogging the Z
|
|
# position of the print head at each probe point and then issuing a
|
|
# NEXT extended g-code command to record the position at that
|
|
# point. The default is false if a [probe] config section is present
|
|
# and true otherwise.
|
|
|
|
|
|
# In a multi-extruder printer add an additional extruder section for
|
|
# each additional extruder. The additional extruder sections should be
|
|
# named "extruder1", "extruder2", "extruder3", and so on. See the
|
|
# "extruder" section in example.cfg for a description of available
|
|
# parameters.
|
|
#[extruder1]
|
|
#step_pin: ar36
|
|
#dir_pin: ar34
|
|
#...
|
|
#shared_heater:
|
|
# If this extruder uses the same heater already defined for another
|
|
# extruder then place the name of that extruder here. For example,
|
|
# should extruder3 and extruder4 share a heater then the extruder3
|
|
# config section should define the heater and the extruder4 section
|
|
# should specify "shared_heater: extruder3". The default is to not
|
|
# reuse an existing heater.
|
|
#deactivate_gcode:
|
|
# A list of G-Code commands (one per line) to execute on a G-Code
|
|
# tool change command (eg, "T1") that deactivates this extruder and
|
|
# activates some other extruder. It only makes sense to define this
|
|
# section on multi-extruder printers. The default is to not run any
|
|
# special G-Code commands on deactivation.
|
|
#activate_gcode:
|
|
# A list of G-Code commands (one per line) to execute on a G-Code
|
|
# tool change command (eg, "T0") that activates this extruder. It
|
|
# only makes sense to define this section on multi-extruder
|
|
# printers. The default is to not run any special G-Code commands on
|
|
# activation.
|
|
|
|
|
|
# Multi-stepper axes. On a cartesian style printer, the stepper
|
|
# controlling a given axis may have additional config blocks defining
|
|
# steppers that should be stepped in concert with the primary
|
|
# stepper. One may define any number of sections with a numeric suffix
|
|
# starting at 1 (for example, "stepper_z1", "stepper_z2", etc.).
|
|
#[stepper_z1]
|
|
#step_pin: ar36
|
|
#dir_pin: ar34
|
|
#enable_pin: !ar30
|
|
#step_distance: .005
|
|
# See the example.cfg for the definition of the above parameters.
|
|
#endstop_pin: ^ar19
|
|
# If an endstop_pin is defined for the additional stepper then the
|
|
# stepper will home until the endstop is triggered. Otherwise, the
|
|
# endstop will home until the endstop on the primary stepper for the
|
|
# axis is triggered.
|
|
|
|
|
|
# Heater cooling fans (one may define any number of sections with a
|
|
# "heater_fan" prefix). A "heater fan" is a fan that will be enabled
|
|
# whenever its associated heater is active. In the event of an MCU
|
|
# software error the heater_fan will be set to its max_power.
|
|
#[heater_fan my_nozzle_fan]
|
|
# See the "fan" section for fan configuration parameters.
|
|
#pin: ar4
|
|
# The remaining variables are specific to heater_fan.
|
|
#heater: extruder
|
|
# Name of the config section defining the heater that this fan is
|
|
# associated with. The default is "extruder".
|
|
#heater_temp: 50.0
|
|
# A temperature (in Celsius) that the heater must drop below before
|
|
# the fan is disabled. The default is 50 Celsius.
|
|
#fan_speed:
|
|
# The fan speed (expressed as a value from 0.0 to 1.0) that the fan
|
|
# will be set to when its associated heater is enabled. The default
|
|
# is max_power.
|
|
|
|
|
|
# Additional micro-controllers (one may define any number of sections
|
|
# with an "mcu" prefix). Additional micro-controllers introduce
|
|
# additional pins that may be configured as heaters, steppers, fans,
|
|
# etc.. For example, if an "[mcu extra_mcu]" section is introduced,
|
|
# then pins such as "extra_mcu:ar9" may then be used elsewhere in the
|
|
# config (where "ar9" is a hardware pin name or alias name on the
|
|
# given mcu).
|
|
#[mcu my_extra_mcu]
|
|
# See the "mcu" section in example.cfg for configuration parameters.
|
|
|
|
|
|
# Servos (one may define any number of sections with a "servo"
|
|
# prefix). The servos may be controlled using the SET_SERVO g-code
|
|
# command. For example: SET_SERVO SERVO=my_servo ANGLE=180
|
|
#[servo my_servo]
|
|
#pin: ar7
|
|
# PWM output pin controlling the servo. This parameter must be
|
|
# provided.
|
|
#maximum_servo_angle: 180
|
|
# The maximum angle (in degrees) that this servo can be set to. The
|
|
# default is 180 degrees.
|
|
#minimum_pulse_width: 0.001
|
|
# The minimum pulse width time (in seconds). This should correspond
|
|
# with an angle of 0 degrees. The default is 0.001 seconds.
|
|
#maximum_pulse_width: 0.002
|
|
# The maximum pulse width time (in seconds). This should correspond
|
|
# with an angle of maximum_servo_angle. The default is 0.002
|
|
# seconds.
|
|
|
|
|
|
# Run-time configurable digital output pins (one may define any number
|
|
# of sections with a "digital_output" prefix). Pins configured here
|
|
# will be setup as digital outputs and one may modify them at run-time
|
|
# using the "SET_PIN PIN=my_pin VALUE=0" extended g-code command.
|
|
#[digital_output my_pin]
|
|
#pin:
|
|
# The pin to configure as a digital output. This parameter must be
|
|
# provided.
|
|
#value:
|
|
# The value to initially set the pin to during MCU configuration
|
|
# (either 0 or 1). The default is 0 (for low voltage).
|
|
#shutdown_value:
|
|
# The value to set the pin to on an MCU shutdown event. The default
|
|
# is 0 (for low voltage).
|
|
|
|
# Statically configured digital output pins (one may define any number
|
|
# of sections with a "static_digital_output" prefix). Pins configured
|
|
# here will be setup as a GPIO output during MCU configuration. They
|
|
# can not be changed at run-time.
|
|
#[static_digital_output my_output_pins]
|
|
#pins:
|
|
# A comma separated list of pins to be set as GPIO output pins. The
|
|
# pin will be set to a high level unless the pin name is prefaced
|
|
# with "!". This parameter must be provided.
|
|
|
|
# Run-time configurable PWM (pulse width modulator) output pins (one
|
|
# may define any number of sections with a "pwm_output" prefix). Pins
|
|
# configured here will be setup as PWM outputs and one may modify them
|
|
# at run-time using the "SET_PIN PIN=my_pin VALUE=.1" extended g-code
|
|
# command.
|
|
#[pwm_output my_pin]
|
|
#pin:
|
|
# The pin to configure as a PWM output. This parameter must be
|
|
# provided.
|
|
#value:
|
|
# The value to initially set the PWM output to during MCU
|
|
# configuration. This is typically set to a number between 0.0 and
|
|
# 1.0 with 1.0 being full on and 0.0 being full off. However, the
|
|
# range may be changed with the 'scale' parameter (see below). The
|
|
# default is 0.
|
|
#shutdown_value:
|
|
# The value to set the pin to on an MCU shutdown event. The default
|
|
# is 0.
|
|
#cycle_time: 0.100
|
|
# The amount of time (in seconds) per PWM cycle. It is recommended
|
|
# this be 10 milliseconds or greater when using software based
|
|
# PWM. The default is 0.100 seconds.
|
|
#hardware_pwm: False
|
|
# Enable this to use hardware PWM instead of software PWM. The
|
|
# default is False.
|
|
#scale:
|
|
# This parameter can be used to alter how the 'value' and
|
|
# 'shutdown_value' parameters are interpreted. If provided, then the
|
|
# 'value' parameter should be between 0.0 and 'scale'. This may be
|
|
# useful when configuring a PWM pin that controls a stepper voltage
|
|
# reference. The 'scale' can be set to the equivalent stepper
|
|
# amperage if the PWM were fully enabled, and then the 'value'
|
|
# parameter can be specified using the desired amperage for the
|
|
# stepper. The default is to not scale the 'value' parameter.
|
|
|
|
# Statically configured PWM output pins (one may define any number of
|
|
# sections with a "static_pwm_output" prefix). Pins configured here
|
|
# will be setup as PWM outputs during MCU configuration. They can not
|
|
# be changed at run-time.
|
|
#[static_pwm_output my_output_pwm]
|
|
#pin:
|
|
#value:
|
|
#cycle_time:
|
|
#hardware_pwm:
|
|
#scale:
|
|
# See the 'pwm_output' section for details on these parameters.
|
|
|
|
|
|
# Multiple pin outputs (one may define any number of sections with a
|
|
# "multi_pin" prefix). A multi_pin output creates an internal pin
|
|
# alias that can modify multiple output pins each time the alias pin
|
|
# is set. For example, one could define a "[multi_pin my_fan]" object
|
|
# containing two pins and then set "pin=multi_pin:my_fan" in the
|
|
# "[fan]" section - on each fan change both output pins would be
|
|
# updated. These aliases may not be used with stepper motor pins.
|
|
#[multi_pin my_multi_pin]
|
|
#pins:
|
|
# A comma separated list of pins associated with this alias. This
|
|
# parameter must be provided.
|
|
|
|
|
|
# Statically configured AD5206 digipots connected via SPI bus (one may
|
|
# define any number of sections with an "ad5206" prefix).
|
|
#[ad5206 my_digipot]
|
|
#enable_pin:
|
|
# The pin corresponding to the AD5206 chip select line. This pin
|
|
# will be set to low at the start of SPI messages and raised to high
|
|
# after the message completes. This parameter must be provided.
|
|
#channel_1:
|
|
#channel_2:
|
|
#channel_3:
|
|
#channel_4:
|
|
#channel_5:
|
|
#channel_6:
|
|
# The value to statically set the given AD5206 channel to. This is
|
|
# typically set to a number between 0.0 and 1.0 with 1.0 being the
|
|
# highest resistance and 0.0 being the lowest resistance. However,
|
|
# the range may be changed with the 'scale' parameter (see
|
|
# below). If a channel is not specified then it is left
|
|
# unconfigured.
|
|
#scale:
|
|
# This parameter can be used to alter how the 'channel_x' parameters
|
|
# are interpreted. If provided, then the 'channel_x' parameters
|
|
# should be between 0.0 and 'scale'. This may be useful when the
|
|
# AD5206 is used to set stepper voltage references. The 'scale' can
|
|
# be set to the equivalent stepper amperage if the AD5206 were at
|
|
# its highest resistance, and then the 'channel_x' parameters can be
|
|
# specified using the desired amperage value for the stepper. The
|
|
# default is to not scale the 'channel_x' parameters.
|
|
|
|
|
|
# Homing override. One may use this mechanism to run a series of
|
|
# g-code commands in place of a G28 found in the normal g-code input.
|
|
# This may be useful on printers that require a specific procedure to
|
|
# home the machine.
|
|
#[homing_override]
|
|
#gcode:
|
|
# A list of G-Code commands (one per line) to execute in place of
|
|
# all G28 commands found in the normal g-code input. If a G28 is
|
|
# contained in this list of commands then it will invoke the normal
|
|
# homing procedure for the printer. The commands listed here must
|
|
# home all axes. This parameter must be provided.
|
|
#set_position_x:
|
|
#set_position_y:
|
|
#set_position_z:
|
|
# If specified, the position to set the printer to (in mm, relative
|
|
# to the coordinate system specified in the config file) prior to
|
|
# running the above g-code commands. Setting this may be useful if
|
|
# an axis must move prior to invoking the normal G28 mechanism for
|
|
# that axis. The default is to not force a position for the axis.
|
|
|
|
|
|
# Replicape support - see the generic-replicape.cfg file for further
|
|
# details.
|
|
#[replicape]
|