282 lines
5.5 KiB
INI
282 lines
5.5 KiB
INI
# This file contains common pin mappings for the Fysetc S6 board.
|
|
# To use this config, the firmware should be compiled for the STM32F446.
|
|
# When calling "menuconfig", enable "extra low-level configuration setup"
|
|
# and select the "12MHz crystal" as clock reference
|
|
# For flashing, write the compiled klipper.bin to memory location 0x08000000
|
|
|
|
# See the example.cfg file for a description of available parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PE11
|
|
dir_pin: PE10
|
|
enable_pin: !PE12
|
|
step_distance: .0125
|
|
endstop_pin: PB14 # PA1 for X-max
|
|
position_endstop: 0
|
|
position_max: 200
|
|
|
|
[stepper_y]
|
|
step_pin: PD8
|
|
dir_pin: PB12
|
|
enable_pin: !PD9
|
|
step_distance: .0125
|
|
endstop_pin: PB13 # PA2 for Y-max
|
|
position_endstop: 0
|
|
position_max: 200
|
|
|
|
[stepper_z]
|
|
step_pin: PD14
|
|
dir_pin: PD13
|
|
enable_pin: !PD15
|
|
step_distance: .0025
|
|
endstop_pin: PA0 # PA3 for Z-max (and servo)
|
|
position_endstop: 0
|
|
position_max: 400
|
|
|
|
[extruder]
|
|
step_pin: PD5
|
|
dir_pin: !PD6
|
|
enable_pin: !PD4
|
|
step_distance: .01
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PB3
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC0
|
|
control: pid
|
|
pid_Kp: 22
|
|
pid_Ki: 1.08
|
|
pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 260
|
|
|
|
#[extruder1]
|
|
#step_pin: PE6
|
|
#dir_pin: !PC13
|
|
#enable_pin: !PE5
|
|
#heater_pin: PB4
|
|
#sensor_pin: PC1
|
|
|
|
#[extruder2]
|
|
#step_pin: PE2
|
|
#dir_pin: !PE4
|
|
#enable_pin: !PE3
|
|
#heater_pin: PB15
|
|
#sensor_pin: PC2
|
|
|
|
[heater_bed]
|
|
heater_pin: PC8
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC3
|
|
control: watermark
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
#fan for printed model FAN0
|
|
[fan]
|
|
pin: PB0
|
|
|
|
#fan for hotend FAN1
|
|
#[heater_fan my_nozzle_fan]
|
|
#pin: PB1
|
|
#shutdown_speed: 1
|
|
|
|
#fan for control board FAN2
|
|
#[heater_fan my_control_fan]
|
|
#pin: PB2
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
########################################
|
|
# TMC UART configuration
|
|
########################################
|
|
|
|
# For TMC UART
|
|
# 1) Remove all jumpers below the stepper drivers.
|
|
# 2) Place a jumper on the "PDN-EN" two-pin header.
|
|
|
|
# For TMC Sensorless homing / DIAG1
|
|
# 1) Place a jumper on the two pin header near the endstop.
|
|
|
|
#[tmc2208 stepper_x]
|
|
#uart_pin: PE8
|
|
#tx_pin: PE9
|
|
#microsteps: 16
|
|
#run_current: 0.8
|
|
#hold_current: 0.5
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2208 stepper_y]
|
|
#uart_pin: PE13
|
|
#tx_pin: PE14
|
|
#microsteps: 16
|
|
#run_current: 0.8
|
|
#hold_current: 0.5
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2208 stepper_z]
|
|
#uart_pin: PD12
|
|
#tx_pin: PD11
|
|
#microsteps: 16
|
|
#run_current: 0.8
|
|
#hold_current: 0.5
|
|
#stealthchop_threshold: 100
|
|
|
|
#[tmc2208 extruder]
|
|
#uart_pin: PA15
|
|
#tx_pin: PD3
|
|
#microsteps: 16
|
|
#run_current: 0.8
|
|
#hold_current: 0.5
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2208 extruder1]
|
|
#uart_pin: PC5
|
|
#tx_pin: PC4
|
|
#microsteps: 16
|
|
#run_current: 0.8
|
|
#hold_current: 0.5
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2208 extruder2]
|
|
#uart_pin: PE0
|
|
#tx_pin: PE1
|
|
#microsteps: 16
|
|
#run_current: 0.8
|
|
#hold_current: 0.5
|
|
#stealthchop_threshold: 250
|
|
|
|
########################################
|
|
# TMC SPI configuration
|
|
########################################
|
|
|
|
# For TMC SPI
|
|
# 1) Remove four jumpers below the stepper drivers, connecting the outermost and middle pins of each row.
|
|
|
|
# For TMC Sensorless homing / DIAG1
|
|
# 1) Place a jumper on the two pin header near the endstop.
|
|
|
|
# SPI pins:
|
|
# SCK PA5
|
|
# MISO PA6
|
|
# MOSI PA7
|
|
|
|
#[tmc2130 stepper_x]
|
|
#spi_bus: spi1
|
|
#cs_pin: PE7
|
|
#diag1_pin: PB14
|
|
#microsteps: 16
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2130 stepper_y]
|
|
#spi_bus: spi1
|
|
#cs_pin: PE15
|
|
#diag1_pin: PB13
|
|
#microsteps: 16
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2130 stepper_z]
|
|
#spi_bus: spi1
|
|
#cs_pin: PD10
|
|
#diag1_pin: PA0
|
|
#microsteps: 16
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2130 extruder]
|
|
#spi_bus: spi1
|
|
#cs_pin: PD7
|
|
#diag1_pin: PA3
|
|
#microsteps: 16
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2130 extruder1]
|
|
#spi_bus: spi1
|
|
#cs_pin: PC14
|
|
#diag1_pin: PA2
|
|
#microsteps: 16
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2130 extruder2]
|
|
#spi_bus: spi1
|
|
#cs_pin: PC15
|
|
#diag1_pin: PA1
|
|
#microsteps: 16
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 250
|
|
|
|
########################################
|
|
# EXP1 / EXP2 (display) pins
|
|
########################################
|
|
|
|
# These must be turned 180° when compared to the default RAMPS layout.
|
|
# The aliases below are 180° turned from what Fysetc considers pin 1,
|
|
# but visually correspond to the plugs on the board.
|
|
|
|
[board_pins]
|
|
aliases:
|
|
# EXP1 header
|
|
EXP1_1=PC9, EXP1_2=PA8,
|
|
EXP1_3=PC11, EXP1_4=PD2,
|
|
EXP1_5=PC10, EXP1_6=PC12, # Slot in the socket on this side
|
|
EXP1_7=PD0, EXP1_8=PD1,
|
|
EXP1_9=<GND>, EXP1_10=<5V>,
|
|
|
|
# EXP2 header
|
|
EXP2_1=PA6, EXP2_2=PA5,
|
|
EXP2_3=PC6, EXP2_4=PA4,
|
|
EXP2_5=PC7, EXP2_6=PA7, # Slot in the socket on this side
|
|
EXP2_7=PB10, EXP2_8=<RST>,
|
|
EXP2_9=<GND>, EXP2_10=<5V>
|
|
|
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
|
|
|
########################################
|
|
# RGB header
|
|
########################################
|
|
|
|
# See the example-extras.cfg file for more information.
|
|
|
|
#[output_pin blue]
|
|
#pin: PB7
|
|
|
|
#[output_pin red]
|
|
#pin: PB6
|
|
|
|
#[output_pin green]
|
|
#pin: PB5
|
|
|
|
########################################
|
|
# Servo
|
|
########################################
|
|
|
|
# See the example-extras.cfg file for more information.
|
|
|
|
#[servo my_servo1]
|
|
#pin: PA3 # shared with ZMAX
|
|
|
|
########################################
|
|
# AUX-3 / SPI header
|
|
########################################
|
|
|
|
# <CD>, <MOSI>, SS, <RESET>
|
|
# <5V> , MISO , SCK, <GND>
|