24 KiB

Raw Blame History

Frequently asked questions

How can I donate to the project?
How do I calculate the step_distance parameter in the printer config file?
Where's my serial port?
When the micro-controller restarts the device changes to /dev/ttyUSB1
The "make flash" command doesn't work
How do I change the serial baud rate?
Can I run Klipper on something other than a Raspberry Pi 3?
Can I run multiple instances of Klipper on the same host machine?
Do I have to use OctoPrint?
Why can't I move the stepper before homing the printer?
Why is the Z position_endstop set to 0.5 in the default configs?
I converted my config from Marlin and the X/Y axes work fine, but I just get a screeching noise when homing the Z axis
My TMC motor driver turns off in the middle of a print
I keep getting random "Lost communication with MCU" errors
My Raspberry Pi keeps rebooting during prints
When I set "restart_method=command" my AVR device just hangs on a restart
Will the heaters be left on if the Raspberry Pi crashes?
How do I convert a Marlin pin number to a Klipper pin name?
How do I cancel an M109/M190 "wait for temperature" request?
Can I find out whether the printer has lost steps?
How do I upgrade to the latest software?

How can I donate to the project?

Thanks. Kevin has a Patreon page at: https://www.patreon.com/koconnor

How do I calculate the step_distance parameter in the printer config file?

If you know the steps per millimeter for the axis then use a calculator to divide 1.0 by steps_per_mm. Then round this number to six decimal places and place it in the config (six decimal places is nano-meter precision).

The step_distance defines the distance that the axis will travel on each motor driver pulse. It can also be calculated from the axis pitch, motor step angle, and driver microstepping. If unsure, do a web search for "calculate steps per mm" to find an online calculator.

Klipper uses step_distance instead of steps_per_mm in order to use consistent units of measurement in the config file. (The config uses millimeters for all distance measurements.) It is believed that steps_per_mm originated as an optimization on old 8-bit micro-controllers (the desire to use a multiply instead of a divide in some low-level code). Continuing to configure this one distance in units of "inverse millimeters" is felt to be quirky and unnecessary.

Where's my serial port?

The general way to find a USB serial port is to run ls /dev/serial/by-id/* from an ssh terminal on the host machine. It will likely produce output similar to the following:

/dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0

The name found in the above command is stable and it is possible to use it in the config file and while flashing the micro-controller code. For example, a flash command might look similar to:

sudo service klipper stop
make flash FLASH_DEVICE=/dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
sudo service klipper start

and the updated config might look like:

[mcu]
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0

Be sure to copy-and-paste the name from the "ls" command that you ran above as the name will be different for each printer.

If you are using multiple micro-controllers and they do not have unique ids (common on boards with a CH340 USB chip) then follow the directions above using the command ls /dev/serial/by-path/* instead.

When the micro-controller restarts the device changes to /dev/ttyUSB1

Follow the directions in the "Where's my serial port?" section to prevent this from occurring.

The "make flash" command doesn't work

The code attempts to flash the device using the most common method for each platform. Unfortunately, there is a lot of variance in flashing methods, so the "make flash" command may not work on all boards.

If you're having an intermittent failure or you do have a standard setup, then double check that Klipper isn't running when flashing (sudo service klipper stop), make sure OctoPrint isn't trying to connect directly to the device (open the Connection tab in the web page and click Disconnect if the Serial Port is set to the device), and make sure FLASH_DEVICE is set correctly for your board (see the question above).

However, if "make flash" just doesn't work for your board, then you will need to manually flash. See if there is a config file in the config directory with specific instructions for flashing the device. Also, check the board manufacturer's documentation to see if it describes how to flash the device. Finally, it may be possible to manually flash the device using tools such as "avrdude" or "bossac" - see the bootloader document for additional information.

How do I change the serial baud rate?

The recommended baud rate for Klipper is 250000. This baud rate works well on all micro-controller boards that Klipper supports. If you've found an online guide recommending a different baud rate, then ignore that part of the guide and continue with the default value of 250000.

If you want to change the baud rate anyway, then the new rate will need to be configured in the micro-controller (during make menuconfig) and that updated code will need to be compiled and flashed to the micro-controller. The Klipper printer.cfg file will also need to be updated to match that baud rate (see the example.cfg file for details). For example:

[mcu]
baud: 250000

The baud rate shown on the OctoPrint web page has no impact on the internal Klipper micro-controller baud rate. Always set the OctoPrint baud rate to 250000 when using Klipper.

The Klipper micro-controller baud rate is not related to the baud rate of the micro-controller's bootloader. See the bootloader document for additional information on bootloaders.

Can I run Klipper on something other than a Raspberry Pi 3?

The recommended hardware is a Raspberry Pi 2, Raspberry Pi 3, or Raspberry Pi 4.

Klipper will run on a Raspberry Pi 1 and on the Raspberry Pi Zero, but these boards don't have enough processing power to run OctoPrint well. It is common for print stalls to occur on these slower machines when printing directly from OctoPrint. (The printer may move faster than OctoPrint can send movement commands.) If you wish to run on one one of these slower boards anyway, consider using the "virtual_sdcard" feature when printing (see config/example-extras.cfg for details).

For running on the Beaglebone, see the Beaglebone specific installation instructions.

Klipper has been run on other machines. The Klipper host software only requires Python running on a Linux (or similar) computer. However, if you wish to run it on a different machine you will need Linux admin knowledge to install the system prerequisites for that particular machine. See the install-octopi.sh script for further information on the necessary Linux admin steps.

Note: If you are not using an OctoPi image, be aware that several Linux distributions enable a "ModemManager" (or similar) package that can disrupt serial communication. (Which can cause Klipper to report seemingly random "Lost communication with MCU" errors.) If you install Klipper on one of these distributions you may need to disable that package.

Can I run multiple instances of Klipper on the same host machine?

It is possible to run multiple instances of the Klipper host software, but doing so requires Linux admin knowledge. The Klipper installation scripts ultimately cause the following Unix command to be run:

~/klippy-env/bin/python ~/klipper/klippy/klippy.py ~/printer.cfg -l /tmp/klippy.log

One can run multiple instances of the above command as long as each instance has its own printer config file, its own log file, and its own pseudo-tty. For example:

~/klippy-env/bin/python ~/klipper/klippy/klippy.py ~/printer2.cfg -l /tmp/klippy2.log -I /tmp/printer2

If you choose to do this, you will need to implement the necessary start, stop, and installation scripts (if any). The install-octopi.sh script and the klipper-start.sh script may be useful as examples.

Do I have to use OctoPrint?

The Klipper software is not dependent on OctoPrint. It is possible to use alternative software to send commands to Klipper, but doing so requires Linux admin knowledge.

Klipper creates a "virtual serial port" via the "/tmp/printer" file, and it emulates a classic 3d-printer serial interface via that file. In general, alternative software may work with Klipper as long as it can be configured to use "/tmp/printer" for the printer serial port.

Why can't I move the stepper before homing the printer?

The code does this to reduce the chance of accidentally commanding the head into the bed or a wall. Once the printer is homed the software attempts to verify each move is within the position_min/max defined in the config file. If the motors are disabled (via an M84 or M18 command) then the motors will need to be homed again prior to movement.

If you want to move the head after canceling a print via OctoPrint, consider changing the OctoPrint cancel sequence to do that for you. It's configured in OctoPrint via a web browser under: Settings->GCODE Scripts

If you want to move the head after a print finishes, consider adding the desired movement to the "custom g-code" section of your slicer.

If the printer requires some additional movement as part of the homing process itself (or fundamentally does not have a homing process) then consider using a safe_z_home or homing_override section in the config file. If you need to move a stepper for diagnostic or debugging purposes then consider adding a force_move section to the config file. See example-extras.cfg for further details on these options.

Why is the Z position_endstop set to 0.5 in the default configs?

For cartesian style printers the Z position_endstop specifies how far the nozzle is from the bed when the endstop triggers. If possible, it is recommended to use a Z-max endstop and home away from the bed (as this reduces the potential for bed collisions). However, if one must home towards the bed then it is recommended to position the endstop so it triggers when the nozzle is still a small distance away from the bed. This way, when homing the axis, it will stop before the nozzle touches the bed. See the bed level document for more information.

I converted my config from Marlin and the X/Y axes work fine, but I just get a screeching noise when homing the Z axis

Short answer: First, make sure you have verified the stepper configuration as described in the config check document. If the problem persists, try reducing the max_z_velocity setting in the printer config.

Long answer: In practice Marlin can typically only step at a rate of around 10000 steps per second. If it is requested to move at a speed that would require a higher step rate then Marlin will generally just step as fast as it can. Klipper is able to achieve much higher step rates, but the stepper motor may not have sufficient torque to move at a higher speed. So, for a Z axis with a very precise step_distance the actual obtainable max_z_velocity may be smaller than what is configured in Marlin.

My TMC motor driver turns off in the middle of a print

Short answer: Do not use the TMC2208 driver in "standalone mode" with Klipper! Do not use the TMC2224 driver in "stealthchop standalone mode" with Klipper!

Long answer: Klipper implements very precise timing.

In the above picture, if Klipper is requested to move along the red line and if each black line represents the nominal location to step a stepper, then in the middle of that movement Klipper will arrange to take a step, change the step direction, and then step back. Klipper can perform this step, direction change, and step back in a very small amount of time.

It is our current understanding that the TMC2208 and TMC2224 will react poorly to this when they are in "stealthchop" mode. (It is not believed any other TMC drivers are impacted.) It is believed that when the driver sees the two step requests in a small time frame that it dramatically increases current in anticipation of high acceleration. That high current can trip the driver's internal "over current" detection which causes the driver to disable itself.

This pattern of steps can occur on all stepper motors and on all robot kinematics.

The TMC2208 and TMC2224 do work well with Klipper when run-time configuration mode is used (that is, when a wire is routed from the micro-controller to the PDN-UART pin and the printer config file has a corresponding [tmc2208] config section). When using run-time configuration, either configure the drivers to use "spreadcycle mode" or configure them to use "stealthchop mode" with a reasonable "stealthchop threshold". If one wishes to exclusively use "stealthchop" mode with run-time UART configuration then make sure the stealthchop_threshold is no more than about 10% greater than the maximum velocity of the given axis. It is speculated that with a reasonable stealthchop threshold, then if Klipper sends a "step, direction change, step back" sequence, the driver will briefly transition from stealthchop mode, to spreadcycle mode, and back to stealthchop mode, which should be harmless.

I keep getting random "Lost communication with MCU" errors

This is commonly caused by hardware errors on the USB connection between the host machine and the micro-controller. Things to look for:

Use a good quality USB cable between the host machine and micro-controller. Make sure the plugs are secure.
If using a Raspberry Pi, use a good quality power supply for the Raspberry Pi and use a good quality USB cable to connect that power supply to the Pi. If you get "under voltage" warnings from OctoPrint, this is related to the power supply and it must be fixed.
Make sure the printer's power supply is not being overloaded. (Power fluctuations to the micro-controller's USB chip may result in resets of that chip.)
Verify stepper, heater, and other printer wires are not crimped or frayed. (Printer movement may place stress on a faulty wire causing it to lose contact, briefly short, or generate excessive noise.)
There have been reports of high USB noise when both the printer's power supply and the host's 5V power supply are mixed. (If you find that the micro-controller powers on when either the printer's power supply is on or the USB cable is plugged in, then it indicates the 5V power supplies are being mixed.) It may help to configure the micro-controller to use power from only one source. (Alternatively, if the micro-controller board can not configure its power source, one may modify a USB cable so that it does not carry 5V power between the host and micro-controller.)

My Raspberry Pi keeps rebooting during prints

This is most likely do to voltage fluctuations. Follow the same troubleshooting steps for a "Lost communication with MCU" error.

When I set "restart_method=command" my AVR device just hangs on a restart

Some old versions of the AVR bootloader have a known bug in watchdog event handling. This typically manifests when the printer.cfg file has restart_method set to "command". When the bug occurs, the AVR device will be unresponsive until power is removed and reapplied to the device (the power or status LEDs may also blink repeatedly until the power is removed).

The workaround is to use a restart_method other than "command" or to flash an updated bootloader to the AVR device. Flashing a new bootloader is a one time step that typically requires an external programmer - see Bootloaders for further details.

Will the heaters be left on if the Raspberry Pi crashes?

The software has been designed to prevent that. Once the host enables a heater, the host software needs to confirm that enablement every 5 seconds. If the micro-controller does not receive a confirmation every 5 seconds it goes into a "shutdown" state which is designed to turn off all heaters and stepper motors.

See the "config_digital_out" command in the MCU commands document for further details.

In addition, the micro-controller software is configured with a minimum and maximum temperature range for each heater at startup (see the min_temp and max_temp parameters in the example.cfg file for details). If the micro-controller detects that the temperature is outside of that range then it will also enter a "shutdown" state.

Separately, the host software also implements code to check that heaters and temperature sensors are functioning correctly. See the "verify_heater" section of the example-extras.cfg for further details.

How do I convert a Marlin pin number to a Klipper pin name?

Short answer: In some cases one can use Klipper's pin_map: arduino feature. Otherwise, for "digital" pins, one method is to search for the requested pin in Marlin's fastio header files. The Atmega2560 and Atmega1280 chips use fastio_1280.h, while the Atmega644p and Atmega1284p chips use fastio_644.h. For example, if you are looking to translate Marlin's digital pin number 23 on an atmega2560 then one could find the following line in Marlin's fastio_1280.h file:

#define DIO23_PIN PINA1

The DIO23 indicates the line is for Marlin's pin 23 and the PINA1 indicates the pin uses the hardware name of PA1. Klipper uses the hardware names (eg, PA1).

Long answer: Klipper uses the standard pin names defined by the micro-controller. On the Atmega chips these hardware pins have names like PA4, PC7, or PD2.

Long ago, the Arduino project decided to avoid using the standard hardware names in favor of their own pin names based on incrementing numbers - these Arduino names generally look like D23 or A14. This was an unfortunate choice that has lead to a great deal of confusion. In particular the Arduino pin numbers frequently don't translate to the same hardware names. For example, D21 is PD0 on one common Arduino board, but is PC7 on another common Arduino board.

In order to support 3d printers based on real Arduino boards, Klipper supports the Arduino pin aliases. This feature is enabled by adding pin_map: arduino to the [mcu] section of the config file. When these aliases are enabled, Klipper understands pin names that start with the prefix "ar" (eg, Arduino pin D23 is Klipper alias ar23) and the prefix "analog" (eg, Arduino pin A14 is Klipper alias analog14). Klipper does not use the Arduino names directly because we feel a name like D7 is too easily confused with the hardware name PD7.

Marlin primarily follows the Arduino pin numbering scheme. However, Marlin supports a few chips that Arduino does not support and in some cases it supports pins that Arduino boards do not expose. In these cases, Marlin chose their own pin numbering scheme. Klipper does not support these custom pin numbers - check Marlin's fastio headers (see above) to translate these pin numbers to their standard hardware names.

How do I cancel an M109/M190 "wait for temperature" request?

Navigate to the OctoPrint terminal tab and issue an M112 command in the terminal box. The M112 command will cause Klipper to enter into a "shutdown" state, and it will cause OctoPrint to disconnect from Klipper. Navigate to the OctoPrint connection area and click on "Connect" to cause OctoPrint to reconnect. Navigate back to the terminal tab and issue a FIRMWARE_RESTART command to clear the Klipper error state. After completing this sequence, the previous heating request will be canceled and a new print may be started.

Can I find out whether the printer has lost steps?

In a way, yes. Home the printer, issue a GET_POSITION command, run your print, home again and issue another GET_POSITION. Then compare the values in the mcu: line.

This might be helpful to tune settings like stepper motor currents, accelerations and speeds without needing to actually print something and waste filament: just run some high-speed moves in between the GET_POSITION commands.

Note that endstop switches themselves tend to trigger at slightly different positions, so a difference of a couple of microsteps is likely the result of endstop inaccuracies. A stepper motor itself can only lose steps in increments of 4 full steps. (So, if one is using 16 microsteps, then a lost step on the stepper would result in the "mcu:" step counter being off by a multiple of 64 microsteps.)

How do I upgrade to the latest software?

The first step to upgrading the software is to review the latest config changes document. On occasion, changes are made to the software that require users to update their settings as part of a software upgrade. It is a good idea to review this document prior to upgrading.

When ready to upgrade, the general method is to ssh into the Raspberry Pi and run:

cd ~/klipper
git pull
~/klipper/scripts/install-octopi.sh

Then one can recompile and flash the micro-controller code. For example:

make menuconfig
make clean
make

sudo service klipper stop
make flash FLASH_DEVICE=/dev/ttyACM0
sudo service klipper start

However, it's often the case that only the host software changes. In this case, one can update and restart just the host software with:

cd ~/klipper
git pull
sudo service klipper restart

If after using this shortcut the software warns about needing to reflash the micro-controller or some other unusual error occurs, then follow the full upgrade steps outlined above.

If any errors persist then double check the config changes document, as you may need to modify the printer configuration.

Note that the RESTART and FIRMWARE_RESTART g-code commands do not load new software - the above "sudo service klipper restart" and "make flash" commands are needed for a software change to take effect.

24 KiB Raw Blame History