..
display
menu: Don't peek into printer.objects member variable
2019-01-08 12:03:46 -05:00
__init__.py
…
ad5206.py
ad5206: Use bus.py helper code for spi
2018-11-21 12:12:31 -05:00
adc_temperature.py
adc_temperature: Add support for linear interpolation of resistances
2019-01-21 21:28:25 -05:00
bed_mesh.py
klippy: Convert printer_state("connect") to an event handler
2019-01-08 11:09:55 -05:00
bed_tilt.py
klippy: Convert printer_state("connect") to an event handler
2019-01-08 11:09:55 -05:00
bltouch.py
bltouch: Take into account clock skew when calculating command duration
2019-01-21 09:56:08 -05:00
bus.py
i2ccmds: Pass the i2c address as a 7-bit number (0-127)
2019-01-07 20:00:44 -05:00
buttons.py
…
controller_fan.py
controller_fan: Add support for a fan cooling the controller-board ( #1070 )
2019-01-10 12:12:15 -05:00
delta_calibrate.py
delta_calibrate: Do not automatically run G28 on DELTA_CALIBRATE
2018-10-22 11:26:01 -04:00
endstop_phase.py
tmc2660: Add endstop phase detection functionality to TMC2660 extra ( #816 )
2018-10-24 16:01:12 -04:00
fan.py
…
force_move.py
…
gcode_macro.py
…
heater_bed.py
heater: take a gcode_id when setting up a heater ( #1028 )
2019-01-02 17:44:02 -05:00
heater_fan.py
klippy: Convert printer_state("ready") to an event handler
2019-01-08 10:59:43 -05:00
homing_override.py
…
idle_timeout.py
klippy: Convert printer_state("ready") to an event handler
2019-01-08 10:59:43 -05:00
mcp4451.py
i2ccmds: Pass the i2c address as a 7-bit number (0-127)
2019-01-07 20:00:44 -05:00
mcp4728.py
mcp4728: Add initial support for the mcp4728 i2c dac chip
2019-01-02 18:17:56 -05:00
multi_pin.py
…
output_pin.py
…
pid_calibrate.py
…
probe.py
bltouch: Add initial support for a bltouch "extras" module
2018-11-30 11:34:20 -05:00
quad_gantry_level.py
klippy: Convert printer_state("connect") to an event handler
2019-01-08 11:09:55 -05:00
query_endstops.py
…
replicape.py
replicape: Use bus.py helper code for spi
2018-11-21 12:12:31 -05:00
respond.py
respond: An extra for sending messages to the printer host. ( #1053 )
2019-01-02 17:45:35 -05:00
servo.py
klippy: Convert printer_state("ready") to an event handler
2019-01-08 10:59:43 -05:00
spi_temperature.py
spi_temperature: Use bus.py helper code for spi
2018-11-21 12:12:31 -05:00
static_digital_output.py
…
statistics.py
klippy: Convert printer_state("ready") to an event handler
2019-01-08 10:59:43 -05:00
sx1509.py
i2ccmds: Pass the i2c address as a 7-bit number (0-127)
2019-01-07 20:00:44 -05:00
temperature_fan.py
…
thermistor.py
adc_temperature: Move PrinterADCtoTemperature to adc_temperature.py
2019-01-21 20:24:51 -05:00
tmc2130.py
tmc2130: Use bus.py helper code for spi
2018-11-21 12:12:31 -05:00
tmc2208.py
tmc2208: Check for debugging mode before checking for a retransmit
2019-01-10 09:55:54 -05:00
tmc2660.py
tmc2660: error and whitespace fixes
2018-12-27 11:44:41 -05:00
verify_heater.py
klippy: Convert printer_state("connect") to an event handler
2019-01-08 11:09:55 -05:00
virtual_sdcard.py
klippy: Convert printer_state("shutdown") to an event handler
2019-01-08 10:59:43 -05:00
z_tilt.py
klippy: Convert printer_state("connect") to an event handler
2019-01-08 11:09:55 -05:00
7327394c50