82 lines
2.1 KiB
INI
82 lines
2.1 KiB
INI
# This file contains common pin mappings for the Duet3 1LC. To use
|
|
# this config, the firmware should be compiled for the SAMC21G18 with:
|
|
# Bootloader offset of "No Bootloader"
|
|
# Clock Reference of "25 Mhz crystal" if the board version is v1.1 or later
|
|
# Clock Reference of "12 Mhz crystal" if the board version is v1.0 or earlier
|
|
# Communication interface of "CAN bus (on PA25/PA24)"
|
|
|
|
# To flash the board use a debugger, or use a raspberry pi and follow
|
|
# the instructions at docs/Bootloaders.md fot the SAMC21. You may
|
|
# supply power to the 1LC by connecting the 3.3v rail on the Pi to the
|
|
# 5v input of the SWD header on the 1LC.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
|
|
# Pins for reference, v1.3 board:
|
|
# Driver Step Pin - PA27
|
|
# Driver Dir Pin - PA28
|
|
# Driver Enable - !PB2
|
|
# Thermistor Pins - TEMP0:PB9 TEMP1:PA2
|
|
# Pullup Resistor - 2200
|
|
# Vssa Sense:PA6 | Vref Sense:PA7
|
|
# Current Sense resistor for drivers - 0.091ohm
|
|
# CAN Pins - CAN0_TX:PA24 CAN0_RX:PA25
|
|
# Heaters - OUT_0:PA11
|
|
# Fan outputs - OUT_1:PA10 OUT_2:PB11
|
|
# Tach Pins for Fans - OUT_1_TACHO:PA13 OUT_2_TACHO:PB10
|
|
# GPIO_out - IO0:PA12
|
|
# GPIO_in - IO0:PA9 IO1:PA21 IO2:PA18
|
|
# Driver Diag - 0:PB3
|
|
|
|
[adc_scaled toolboard_vref_scaled]
|
|
vref_pin: toolboard:PA7
|
|
vssa_pin: toolboard:PA6
|
|
|
|
[extruder]
|
|
step_pin: toolboard:PA27
|
|
dir_pin: toolboard:PA28
|
|
enable_pin: !toolboard:PB2
|
|
rotation_distance: 23.1336867485061
|
|
gear_ratio: 50:10
|
|
microsteps: 64
|
|
full_steps_per_rotation: 200
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.75
|
|
heater_pin: toolboard:PA11
|
|
sensor_type: PT1000
|
|
sensor_pin: toolboard_vref_scaled:PB9
|
|
pullup_resistor: 2200
|
|
min_temp: 0
|
|
max_temp: 280
|
|
max_power: 1.0
|
|
control: pid
|
|
pwm_cycle_time: 0.01666
|
|
pid_Kp: 26.454
|
|
pid_Ki: 1.357
|
|
pid_Kd: 128.955
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: toolboard:PA20
|
|
tx_pin: toolboard:PA22
|
|
interpolate: False
|
|
run_current: 0.35
|
|
sense_resistor: 0.091
|
|
|
|
[fan]
|
|
pin: toolboard:PA10
|
|
tachometer_pin: toolboard:PA13
|
|
|
|
[heater_fan hotend_fan]
|
|
pin: toolboard:PB11
|
|
tachometer_pin: toolboard:PB10
|
|
heater: extruder
|
|
heater_temp: 50.0
|
|
|
|
[probe]
|
|
pin: toolboard:PA9
|
|
z_offset: 20
|
|
|
|
[mcu toolboard]
|
|
canbus_uuid: 4b194673554e
|