klipper/lib/hal-stm32f1/source
Grigori Goronzy 75d5737211 Add STM32F103 port
Add a fully functional STM32F1 port, currently mostly targeting STM32F103
microcontrollers. This requires an 8 MHz XTAL. The maximum possible step rate
is around 282K steps per second.

This uses stm32flash to burn the firmware. The bootloader needs to be started
by setting BOOT0 to 1 and resetting the MCU. There is no automatic bootloader,
unlike on Arduino.

Signed-off-by: Grigori Goronzy <greg@kinoho.net>
2018-04-09 18:08:29 -04:00
..
stm32f1xx_hal.c
stm32f1xx_hal_adc.c
stm32f1xx_hal_adc_ex.c
stm32f1xx_hal_can.c
stm32f1xx_hal_cec.c
stm32f1xx_hal_cortex.c
stm32f1xx_hal_crc.c
stm32f1xx_hal_dac.c
stm32f1xx_hal_dac_ex.c
stm32f1xx_hal_dma.c
stm32f1xx_hal_eth.c
stm32f1xx_hal_flash.c
stm32f1xx_hal_flash_ex.c
stm32f1xx_hal_gpio.c
stm32f1xx_hal_gpio_ex.c
stm32f1xx_hal_hcd.c
stm32f1xx_hal_i2c.c
stm32f1xx_hal_i2s.c
stm32f1xx_hal_irda.c
stm32f1xx_hal_iwdg.c
stm32f1xx_hal_mmc.c
stm32f1xx_hal_msp_template.c
stm32f1xx_hal_nand.c
stm32f1xx_hal_nor.c
stm32f1xx_hal_pccard.c
stm32f1xx_hal_pcd.c
stm32f1xx_hal_pcd_ex.c
stm32f1xx_hal_pwr.c
stm32f1xx_hal_rcc.c
stm32f1xx_hal_rcc_ex.c
stm32f1xx_hal_rtc.c
stm32f1xx_hal_rtc_ex.c
stm32f1xx_hal_sd.c
stm32f1xx_hal_smartcard.c
stm32f1xx_hal_spi.c
stm32f1xx_hal_spi_ex.c
stm32f1xx_hal_sram.c
stm32f1xx_hal_tim.c
stm32f1xx_hal_tim_ex.c
stm32f1xx_hal_timebase_rtc_alarm_template.c
stm32f1xx_hal_timebase_tim_template.c
stm32f1xx_hal_uart.c
stm32f1xx_hal_usart.c
stm32f1xx_hal_wwdg.c
stm32f1xx_ll_adc.c
stm32f1xx_ll_crc.c
stm32f1xx_ll_dac.c
stm32f1xx_ll_dma.c
stm32f1xx_ll_exti.c
stm32f1xx_ll_fsmc.c
stm32f1xx_ll_gpio.c
stm32f1xx_ll_i2c.c
stm32f1xx_ll_pwr.c
stm32f1xx_ll_rcc.c
stm32f1xx_ll_rtc.c
stm32f1xx_ll_sdmmc.c
stm32f1xx_ll_spi.c
stm32f1xx_ll_tim.c
stm32f1xx_ll_usart.c
stm32f1xx_ll_usb.c
stm32f1xx_ll_utils.c