128 lines
2.7 KiB
INI
128 lines
2.7 KiB
INI
# This file contains pin mappings for the Creality Sermoon D1 with
|
|
# Rev. 4.3.1 Motherboard.
|
|
|
|
# To use this config, during "make menuconfig" select the STM32F103
|
|
# with a "28KiB bootloader" and serial (on USART1 PA10/PA9)
|
|
# communication.
|
|
|
|
# Flash this firmware by copying "out/klipper.bin" to a SD card and
|
|
# turning on the printer with the card inserted. The firmware
|
|
# filename must end in ".bin" and must not match the last filename
|
|
# that was flashed.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PC2
|
|
dir_pin: !PB9
|
|
enable_pin: !PC3
|
|
rotation_distance: 40
|
|
microsteps: 16
|
|
endstop_pin: ^PA5
|
|
position_min: -5
|
|
position_endstop: -5
|
|
position_max: 280
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: PB8
|
|
dir_pin: PB7
|
|
enable_pin: !PC3
|
|
rotation_distance: 40
|
|
microsteps: 16
|
|
endstop_pin: ^PA6
|
|
position_min: -2
|
|
position_endstop: -2
|
|
position_max: 260
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: PB6
|
|
dir_pin: PB5
|
|
enable_pin: !PC3
|
|
rotation_distance: 8
|
|
microsteps: 16
|
|
position_endstop: 0.0 # disable to use BLTouch
|
|
endstop_pin: ^PA7 # disable to use BLTouch
|
|
# endstop_pin: probe:z_virtual_endstop # enable to use BLTouch
|
|
# position_min: -5 # enable to use BLTouch
|
|
position_max: 300
|
|
homing_speed: 4
|
|
second_homing_speed: 1
|
|
homing_retract_dist: 2.0
|
|
|
|
[extruder]
|
|
max_extrude_only_distance: 1000.0
|
|
step_pin: PB4
|
|
dir_pin: PB3
|
|
enable_pin: !PC3
|
|
microsteps: 16
|
|
rotation_distance: 34.936
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PA1
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC5
|
|
control: pid
|
|
pid_kp: 26.163
|
|
pid_ki: 1.418
|
|
pid_kd: 120.675
|
|
min_temp: 0
|
|
max_temp: 260
|
|
|
|
[heater_bed]
|
|
heater_pin: PA2
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC4
|
|
control: pid
|
|
pid_Kp: 76.301
|
|
pid_Ki: 1.707
|
|
pid_Kd: 852.669
|
|
min_temp: 0
|
|
max_temp: 100
|
|
|
|
[fan]
|
|
pin: PA0
|
|
kick_start_time: 0.5
|
|
|
|
[mcu]
|
|
#use command ls /dev/serial/by-id/* to find the printer connected via USB
|
|
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
|
restart_method: command
|
|
|
|
# Before printing the PROBE_CALIBRATE command needs to be issued
|
|
# to run the probe calibration procedure, described at
|
|
# docs/Probe_Calibrate.md, to find the correct z_offset.
|
|
|
|
# [safe_z_home] # enable for BLTouch
|
|
# home_xy_position: 150.7, 137
|
|
# speed: 100
|
|
# z_hop: 10
|
|
# z_hop_speed: 5
|
|
|
|
# [bltouch]
|
|
# sensor_pin: ^PB1
|
|
# control_pin: PB0
|
|
# x_offset: 20
|
|
# y_offset: 0
|
|
# z_offset: 2
|
|
# speed: 3.0
|
|
|
|
# [bed_mesh] # enable for BLTouch
|
|
# speed: 100
|
|
# mesh_min: 20, 15
|
|
# mesh_max: 250, 240
|
|
# algorithm: bicubic
|
|
# probe_count: 5, 5
|
|
|
|
[filament_switch_sensor filament_sensor]
|
|
pause_on_runout: true
|
|
switch_pin: !PA4
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 500
|
|
max_accel: 500
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|