132 lines
2.2 KiB
INI
132 lines
2.2 KiB
INI
# Support for Tevo Flash. To use this config, the firmware should be
|
|
# compiled for the AVR atmega2560.
|
|
|
|
# Note, this config has only been tested on a modified Tevo Flash
|
|
# (using a Bondtech BMG extruder). If using a stock printer it may be
|
|
# necessary to update the extruder rotation_distance parameter.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: ar54
|
|
dir_pin: !ar55
|
|
enable_pin: !ar38
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: !ar3
|
|
position_endstop: -13
|
|
position_min: -13
|
|
position_max: 235
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: ar60
|
|
dir_pin: ar61
|
|
enable_pin: !ar56
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: !ar14
|
|
position_endstop: -3
|
|
position_min: -3
|
|
position_max: 235
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: ar46
|
|
dir_pin: ar48
|
|
enable_pin: !ar62
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
position_max: 250
|
|
endstop_pin: probe:z_virtual_endstop
|
|
position_min: -2
|
|
|
|
[stepper_z1]
|
|
step_pin: ar36
|
|
dir_pin: ar34
|
|
enable_pin: !ar30
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
|
|
[extruder]
|
|
step_pin: ar26
|
|
dir_pin: ar28
|
|
enable_pin: !ar24
|
|
microsteps: 16
|
|
gear_ratio: 3:1
|
|
rotation_distance: 23.050
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: ar10
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: analog13
|
|
control: pid
|
|
pid_Kp: 18.547
|
|
pid_Ki: 0.788
|
|
pid_Kd: 109.193
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
[heater_bed]
|
|
heater_pin: ar8
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: analog14
|
|
control: pid
|
|
pid_Kp: 38.824
|
|
pid_Ki: 0.539
|
|
pid_Kd: 698.838
|
|
min_temp: 0
|
|
max_temp: 70
|
|
|
|
[heater_fan my_nozzle_fan]
|
|
pin: ar7
|
|
|
|
[fan]
|
|
pin: ar9
|
|
|
|
[mcu]
|
|
serial: /dev/ttyUSB0
|
|
pin_map: arduino
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 1000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
[display]
|
|
lcd_type: uc1701
|
|
cs_pin: ar25
|
|
a0_pin: ar27
|
|
encoder_pins: ^!ar31, ^!ar33
|
|
click_pin: ^!ar35
|
|
kill_pin: ar64
|
|
|
|
[bltouch]
|
|
sensor_pin: ar18
|
|
control_pin: ar11
|
|
x_offset: 0
|
|
y_offset: 18
|
|
z_offset: 1.64
|
|
samples: 3
|
|
sample_retract_dist: 5
|
|
|
|
# The homing_override section modifies the default G28 behavior
|
|
[homing_override]
|
|
set_position_z: 0
|
|
axes: z
|
|
gcode:
|
|
G90
|
|
G1 Z5 F600
|
|
G28 X0 Y0
|
|
G1 X118 Y118 F3600
|
|
G28 Z0
|
|
|
|
# Mesh Bed Leveling.
|
|
[bed_mesh]
|
|
mesh_min: 5,18
|
|
mesh_max: 230,228
|
|
probe_count: 9,9
|
|
algorithm: bicubic
|