193 lines
7.1 KiB
Markdown
193 lines
7.1 KiB
Markdown
These instructions assume the software will run on a Raspberry Pi
|
|
computer in conjunction with OctoPrint. It is recommended that a
|
|
Raspberry Pi 2 or Raspberry Pi 3 computer be used as the host machine
|
|
(see the
|
|
[FAQ](FAQ.md#can-i-run-klipper-on-something-other-than-a-raspberry-pi-3)
|
|
for other machines).
|
|
|
|
Klipper currently supports Atmel ATmega based micro-controllers,
|
|
Arduino Due (Atmel SAM3x8e ARM micro-controller), Smoothieboard (ARM
|
|
LPC176x), and [Beaglebone PRU](beaglebone.md) based printers.
|
|
|
|
Prepping an OS image
|
|
====================
|
|
|
|
Start by installing [OctoPi](https://github.com/guysoft/OctoPi) on the
|
|
Raspberry Pi computer. Use OctoPi v0.14.0 or later - see the
|
|
[octopi releases](https://github.com/guysoft/OctoPi/releases) for
|
|
release information. One should verify that OctoPi boots and that the
|
|
OctoPrint web server works. After connecting to the OctoPrint web
|
|
page, follow the prompt to upgrade OctoPrint to v1.3.7 or later.
|
|
|
|
After installing OctoPi and upgrading OctoPrint, it will be necessary
|
|
to ssh into the target machine to run a handful of system commands. If
|
|
using a Linux or MacOS desktop, then the "ssh" software should already
|
|
be installed on the desktop. There are free ssh clients available for
|
|
other desktops (eg,
|
|
[PuTTY](https://www.chiark.greenend.org.uk/~sgtatham/putty/)). Use the
|
|
ssh utility to connect to the Raspberry Pi (ssh pi@octopi -- password
|
|
is "raspberry") and run the following commands:
|
|
|
|
```
|
|
git clone https://github.com/KevinOConnor/klipper
|
|
./klipper/scripts/install-octopi.sh
|
|
```
|
|
|
|
The above will download Klipper, install some system dependencies,
|
|
setup Klipper to run at system startup, and start the Klipper host
|
|
software. It will require an internet connection and it may take a few
|
|
minutes to complete.
|
|
|
|
Building and flashing the micro-controller
|
|
==========================================
|
|
|
|
To compile the micro-controller code, start by running these commands
|
|
on the Raspberry Pi:
|
|
|
|
```
|
|
cd ~/klipper/
|
|
make menuconfig
|
|
```
|
|
|
|
Select the appropriate micro-controller and review any other options
|
|
provided. Once configured, run:
|
|
|
|
```
|
|
make
|
|
```
|
|
|
|
It is necessary to determine the serial port connected to the
|
|
micro-controller. For micro-controllers that connect via USB, run the
|
|
following:
|
|
|
|
```
|
|
ls /dev/serial/by-id/*
|
|
```
|
|
|
|
It should report something similar to the following:
|
|
|
|
```
|
|
/dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
|
|
```
|
|
|
|
It's common for each printer to have its own unique serial port name.
|
|
This unique name will be used when flashing the micro-controller. It's
|
|
possible there may be multiple lines in the above output - if so,
|
|
choose the line corresponding to the micro-controller (see the
|
|
[FAQ](FAQ.md#wheres-my-serial-port) for more information).
|
|
|
|
For common micro-controllers, the code can be flashed with something
|
|
similar to:
|
|
|
|
```
|
|
sudo service klipper stop
|
|
make flash FLASH_DEVICE=/dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
|
|
sudo service klipper start
|
|
```
|
|
|
|
Be sure to update the FLASH_DEVICE with the printer's unique serial
|
|
port name.
|
|
|
|
When flashing for the first time, make sure that OctoPrint is not
|
|
connected directly to the printer (from the OctoPrint web page, under
|
|
the "Connection" section, click "Disconnect").
|
|
|
|
Configuring OctoPrint to use Klipper
|
|
====================================
|
|
|
|
The OctoPrint web server needs to be configured to communicate with
|
|
the Klipper host software. Using a web browser, login to the OctoPrint
|
|
web page and then configure the following items:
|
|
|
|
Navigate to the Settings tab (the wrench icon at the top of the
|
|
page). Under "Serial Connection" in "Additional serial ports" add
|
|
"/tmp/printer". Then click "Save".
|
|
|
|
Enter the Settings tab again and under "Serial Connection" change the
|
|
"Serial Port" setting to "/tmp/printer".
|
|
|
|
In the Settings tab, navigate to the "Behavior" sub-tab and select the
|
|
"Cancel any ongoing prints but stay connected to the printer"
|
|
option. Click "Save".
|
|
|
|
From the main page, under the "Connection" section (at the top left of
|
|
the page) make sure the "Serial Port" is set to "/tmp/printer" and
|
|
click "Connect". (If "/tmp/printer" is not an available selection then
|
|
try reloading the page.)
|
|
|
|
Once connected, navigate to the "Terminal" tab and type "status"
|
|
(without the quotes) into the command entry box and click "Send". The
|
|
terminal window will likely report there is an error opening the
|
|
config file - that means OctoPrint is successfully communicating with
|
|
Klipper. Proceed to the next section.
|
|
|
|
Configuring Klipper
|
|
===================
|
|
|
|
The Klipper configuration is stored in a text file on the Raspberry
|
|
Pi. Take a look at the example config files in the
|
|
[config directory](../config/). The
|
|
[example.cfg](../config/example.cfg) file contains documentation on
|
|
command parameters and it can also be used as an initial config file
|
|
template. However, for most printers, one of the other config files
|
|
may be a more concise starting point.
|
|
|
|
Arguably the easiest way to update the Klipper configuration file is
|
|
to use a desktop editor that supports editing files over the "scp"
|
|
and/or "sftp" protocols. There are freely available tools that support
|
|
this (eg, Notepad++, WinSCP, and Cyberduck). Use one of the example
|
|
config files as a starting point and save it as a file named
|
|
"printer.cfg" in the home directory of the pi user (ie,
|
|
/home/pi/printer.cfg).
|
|
|
|
Alternatively, one can also copy and edit the file directly on the
|
|
Raspberry Pi via ssh - for example:
|
|
|
|
```
|
|
cp ~/klipper/config/example.cfg ~/printer.cfg
|
|
nano ~/printer.cfg
|
|
```
|
|
|
|
Make sure to review and update each setting that is appropriate for
|
|
the hardware.
|
|
|
|
It's common for each printer to have its own unique name for the
|
|
micro-controller. The name may change after flashing Klipper, so rerun
|
|
the `ls /dev/serial/by-id/*` command and then update the config file
|
|
with the unique name. For example, update the `[mcu]` section to look
|
|
something similar to:
|
|
|
|
```
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
|
|
```
|
|
|
|
After creating and editing the file it will be necessary to issue a
|
|
"restart" command in the OctoPrint web terminal to load the config. A
|
|
"status" command will report the printer is ready if the Klipper
|
|
config file is successfully read and the micro-controller is
|
|
successfully found and configured. It is not unusual to have
|
|
configuration errors during the initial setup - update the printer
|
|
config file and issue "restart" until "status" reports the printer is
|
|
ready.
|
|
|
|
Klipper reports error messages via the OctoPrint terminal tab. The
|
|
"status" command can be used to re-report error messages. The default
|
|
Klipper startup script also places a log in **/tmp/klippy.log** which
|
|
provides more detailed information.
|
|
|
|
In addition to common g-code commands, Klipper supports a few extended
|
|
commands - "status" and "restart" are examples of these commands. Use
|
|
the "help" command to get a list of other extended commands.
|
|
|
|
After Klipper reports that the printer is ready go on to the
|
|
[config check document](Config_checks.md) to perform some basic checks
|
|
on the pin definitions in the config file.
|
|
|
|
Contacting the developers
|
|
=========================
|
|
|
|
Be sure to see the [FAQ](FAQ.md) for answers to some common questions.
|
|
See the [contact page](Contact.md) to report a bug or to contact the
|
|
developers.
|