3diy
/
klipper
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
klipper/lib/hal-stm32f0/source/stm32f0xx_hal_rtc_ex.c

1595 lines
48 KiB
C
Raw Blame History

/**
******************************************************************************
* @file stm32f0xx_hal_rtc_ex.c
* @author MCD Application Team
* @brief Extended RTC HAL module driver.
* This file provides firmware functions to manage the following
* functionalities of the Real Time Clock (RTC) Extended peripheral:
* + RTC Time Stamp functions
* + RTC Tamper functions
* + RTC Wake-up functions
* + Extended Control functions
* + Extended RTC features functions
*
@verbatim
==============================================================================
##### How to use this driver #####
==============================================================================
[..]
(+) Enable the RTC domain access.
(+) Configure the RTC Prescaler (Asynchronous and Synchronous) and RTC hour
format using the HAL_RTC_Init() function.
*** RTC Wake-up configuration ***
================================
[..]
(+) To configure the RTC Wakeup Clock source and Counter use the HAL_RTCEx_SetWakeUpTimer()
function. You can also configure the RTC Wakeup timer with interrupt mode
using the HAL_RTCEx_SetWakeUpTimer_IT() function.
(+) To read the RTC WakeUp Counter register, use the HAL_RTCEx_GetWakeUpTimer()
function.
(@) Not available on F030x4/x6/x8 and F070x6
*** TimeStamp configuration ***
===============================
[..]
(+) Configure the RTC_AF trigger and enable the RTC TimeStamp using the
HAL_RTCEx_SetTimeStamp() function. You can also configure the RTC TimeStamp with
interrupt mode using the HAL_RTCEx_SetTimeStamp_IT() function.
(+) To read the RTC TimeStamp Time and Date register, use the HAL_RTCEx_GetTimeStamp()
function.
*** Tamper configuration ***
============================
[..]
(+) Enable the RTC Tamper and configure the Tamper filter count, trigger Edge
or Level according to the Tamper filter (if equal to 0 Edge else Level)
value, sampling frequency, precharge or discharge and Pull-UP using the
HAL_RTCEx_SetTamper() function. You can configure RTC Tamper in interrupt
mode using HAL_RTCEx_SetTamper_IT() function.
*** Backup Data Registers configuration ***
===========================================
[..]
(+) To write to the RTC Backup Data registers, use the HAL_RTCEx_BKUPWrite()
function.
(+) To read the RTC Backup Data registers, use the HAL_RTCEx_BKUPRead()
function.
(@) Not available on F030x6/x8/xC and F070x6/xB (F0xx Value Line devices)
@endverbatim
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32f0xx_hal.h"
/** @addtogroup STM32F0xx_HAL_Driver
* @{
*/
/** @addtogroup RTCEx
* @brief RTC Extended HAL module driver
* @{
*/
#ifdef HAL_RTC_MODULE_ENABLED
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Exported functions ---------------------------------------------------------*/
/** @addtogroup RTCEx_Exported_Functions
* @{
*/
/** @addtogroup RTCEx_Exported_Functions_Group1
* @brief RTC TimeStamp and Tamper functions
*
@verbatim
===============================================================================
##### RTC TimeStamp and Tamper functions #####
===============================================================================
[..] This section provides functions allowing to configure TimeStamp feature
@endverbatim
* @{
*/
/**
* @brief Set TimeStamp.
* @note This API must be called before enabling the TimeStamp feature.
* @param hrtc RTC handle
* @param TimeStampEdge Specifies the pin edge on which the TimeStamp is
* activated.
* This parameter can be one of the following values:
* @arg RTC_TIMESTAMPEDGE_RISING: the Time stamp event occurs on the
* rising edge of the related pin.
* @arg RTC_TIMESTAMPEDGE_FALLING: the Time stamp event occurs on the
* falling edge of the related pin.
* @param RTC_TimeStampPin specifies the RTC TimeStamp Pin.
* This parameter can be one of the following values:
* @arg RTC_TIMESTAMPPIN_DEFAULT: PC13 is selected as RTC TimeStamp Pin.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_SetTimeStamp(RTC_HandleTypeDef *hrtc, uint32_t TimeStampEdge, uint32_t RTC_TimeStampPin)
{
uint32_t tmpreg = 0U;
/* Check the parameters */
assert_param(IS_TIMESTAMP_EDGE(TimeStampEdge));
assert_param(IS_RTC_TIMESTAMP_PIN(RTC_TimeStampPin));
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
/* Get the RTC_CR register and clear the bits to be configured */
tmpreg = (uint32_t)(hrtc->Instance->CR & (uint32_t)~(RTC_CR_TSEDGE | RTC_CR_TSE));
tmpreg|= TimeStampEdge;
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
/* Configure the Time Stamp TSEDGE and Enable bits */
hrtc->Instance->CR = (uint32_t)tmpreg;
__HAL_RTC_TIMESTAMP_ENABLE(hrtc);
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_OK;
}
/**
* @brief Set TimeStamp with Interrupt.
* @param hrtc RTC handle
* @note This API must be called before enabling the TimeStamp feature.
* @param TimeStampEdge Specifies the pin edge on which the TimeStamp is
* activated.
* This parameter can be one of the following values:
* @arg RTC_TIMESTAMPEDGE_RISING: the Time stamp event occurs on the
* rising edge of the related pin.
* @arg RTC_TIMESTAMPEDGE_FALLING: the Time stamp event occurs on the
* falling edge of the related pin.
* @param RTC_TimeStampPin Specifies the RTC TimeStamp Pin.
* This parameter can be one of the following values:
* @arg RTC_TIMESTAMPPIN_DEFAULT: PC13 is selected as RTC TimeStamp Pin.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_SetTimeStamp_IT(RTC_HandleTypeDef *hrtc, uint32_t TimeStampEdge, uint32_t RTC_TimeStampPin)
{
uint32_t tmpreg = 0U;
/* Check the parameters */
assert_param(IS_TIMESTAMP_EDGE(TimeStampEdge));
assert_param(IS_RTC_TIMESTAMP_PIN(RTC_TimeStampPin));
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
/* Get the RTC_CR register and clear the bits to be configured */
tmpreg = (uint32_t)(hrtc->Instance->CR & (uint32_t)~(RTC_CR_TSEDGE | RTC_CR_TSE));
tmpreg |= TimeStampEdge;
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
/* Configure the Time Stamp TSEDGE and Enable bits */
hrtc->Instance->CR = (uint32_t)tmpreg;
__HAL_RTC_TIMESTAMP_ENABLE(hrtc);
/* Enable IT timestamp */
__HAL_RTC_TIMESTAMP_ENABLE_IT(hrtc,RTC_IT_TS);
/* RTC timestamp Interrupt Configuration: EXTI configuration */
__HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_IT();
__HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_RISING_EDGE();
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
hrtc->State = HAL_RTC_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_OK;
}
/**
* @brief Deactivate TimeStamp.
* @param hrtc RTC handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_DeactivateTimeStamp(RTC_HandleTypeDef *hrtc)
{
uint32_t tmpreg = 0U;
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
/* In case of interrupt mode is used, the interrupt source must disabled */
__HAL_RTC_TIMESTAMP_DISABLE_IT(hrtc, RTC_IT_TS);
/* Get the RTC_CR register and clear the bits to be configured */
tmpreg = (uint32_t)(hrtc->Instance->CR & (uint32_t)~(RTC_CR_TSEDGE | RTC_CR_TSE));
/* Configure the Time Stamp TSEDGE and Enable bits */
hrtc->Instance->CR = (uint32_t)tmpreg;
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
hrtc->State = HAL_RTC_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_OK;
}
/**
* @brief Get the RTC TimeStamp value.
* @param hrtc RTC handle
* @param sTimeStamp Pointer to Time structure
* @param sTimeStampDate Pointer to Date structure
* @param Format specifies the format of the entered parameters.
* This parameter can be one of the following values:
* @arg RTC_FORMAT_BIN: Binary data format
* @arg RTC_FORMAT_BCD: BCD data format
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_GetTimeStamp(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef* sTimeStamp, RTC_DateTypeDef* sTimeStampDate, uint32_t Format)
{
uint32_t tmptime = 0U, tmpdate = 0U;
/* Check the parameters */
assert_param(IS_RTC_FORMAT(Format));
/* Get the TimeStamp time and date registers values */
tmptime = (uint32_t)(hrtc->Instance->TSTR & RTC_TR_RESERVED_MASK);
tmpdate = (uint32_t)(hrtc->Instance->TSDR & RTC_DR_RESERVED_MASK);
/* Fill the Time structure fields with the read parameters */
sTimeStamp->Hours = (uint8_t)((tmptime & (RTC_TR_HT | RTC_TR_HU)) >> 16U);
sTimeStamp->Minutes = (uint8_t)((tmptime & (RTC_TR_MNT | RTC_TR_MNU)) >> 8U);
sTimeStamp->Seconds = (uint8_t)(tmptime & (RTC_TR_ST | RTC_TR_SU));
sTimeStamp->TimeFormat = (uint8_t)((tmptime & (RTC_TR_PM)) >> 16U);
sTimeStamp->SubSeconds = (uint32_t) hrtc->Instance->TSSSR;
/* Fill the Date structure fields with the read parameters */
sTimeStampDate->Year = 0;
sTimeStampDate->Month = (uint8_t)((tmpdate & (RTC_DR_MT | RTC_DR_MU)) >> 8U);
sTimeStampDate->Date = (uint8_t)(tmpdate & (RTC_DR_DT | RTC_DR_DU));
sTimeStampDate->WeekDay = (uint8_t)((tmpdate & (RTC_DR_WDU)) >> 13U);
/* Check the input parameters format */
if(Format == RTC_FORMAT_BIN)
{
/* Convert the TimeStamp structure parameters to Binary format */
sTimeStamp->Hours = (uint8_t)RTC_Bcd2ToByte(sTimeStamp->Hours);
sTimeStamp->Minutes = (uint8_t)RTC_Bcd2ToByte(sTimeStamp->Minutes);
sTimeStamp->Seconds = (uint8_t)RTC_Bcd2ToByte(sTimeStamp->Seconds);
/* Convert the DateTimeStamp structure parameters to Binary format */
sTimeStampDate->Month = (uint8_t)RTC_Bcd2ToByte(sTimeStampDate->Month);
sTimeStampDate->Date = (uint8_t)RTC_Bcd2ToByte(sTimeStampDate->Date);
sTimeStampDate->WeekDay = (uint8_t)RTC_Bcd2ToByte(sTimeStampDate->WeekDay);
}
/* Clear the TIMESTAMP Flag */
__HAL_RTC_TIMESTAMP_CLEAR_FLAG(hrtc, RTC_FLAG_TSF);
return HAL_OK;
}
/**
* @brief Set Tamper
* @note By calling this API we disable the tamper interrupt for all tampers.
* @param hrtc RTC handle
* @param sTamper Pointer to Tamper Structure.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_SetTamper(RTC_HandleTypeDef *hrtc, RTC_TamperTypeDef* sTamper)
{
uint32_t tmpreg = 0U;
/* Check the parameters */
assert_param(IS_RTC_TAMPER(sTamper->Tamper));
assert_param(IS_RTC_TAMPER_TRIGGER(sTamper->Trigger));
assert_param(IS_RTC_TAMPER_FILTER(sTamper->Filter));
assert_param(IS_RTC_TAMPER_SAMPLING_FREQ(sTamper->SamplingFrequency));
assert_param(IS_RTC_TAMPER_PRECHARGE_DURATION(sTamper->PrechargeDuration));
assert_param(IS_RTC_TAMPER_PULLUP_STATE(sTamper->TamperPullUp));
assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sTamper->TimeStampOnTamperDetection));
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
if(sTamper->Trigger != RTC_TAMPERTRIGGER_RISINGEDGE)
{
sTamper->Trigger = (uint32_t)(sTamper->Tamper << 1U);
}
tmpreg = ((uint32_t)sTamper->Tamper | (uint32_t)sTamper->Trigger | (uint32_t)sTamper->Filter |\
(uint32_t)sTamper->SamplingFrequency | (uint32_t)sTamper->PrechargeDuration |\
(uint32_t)sTamper->TamperPullUp | sTamper->TimeStampOnTamperDetection);
hrtc->Instance->TAFCR &= (uint32_t)~((uint32_t)sTamper->Tamper | (uint32_t)(sTamper->Tamper << 1U) | (uint32_t)RTC_TAFCR_TAMPTS |\
(uint32_t)RTC_TAFCR_TAMPFREQ | (uint32_t)RTC_TAFCR_TAMPFLT | (uint32_t)RTC_TAFCR_TAMPPRCH |\
(uint32_t)RTC_TAFCR_TAMPPUDIS | (uint32_t)RTC_TAFCR_TAMPIE);
hrtc->Instance->TAFCR |= tmpreg;
hrtc->State = HAL_RTC_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_OK;
}
/**
* @brief Sets Tamper with interrupt.
* @note By calling this API we force the tamper interrupt for all tampers.
* @param hrtc pointer to a RTC_HandleTypeDef structure that contains
* the configuration information for RTC.
* @param sTamper Pointer to RTC Tamper.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_SetTamper_IT(RTC_HandleTypeDef *hrtc, RTC_TamperTypeDef* sTamper)
{
uint32_t tmpreg = 0U;
/* Check the parameters */
assert_param(IS_RTC_TAMPER(sTamper->Tamper));
assert_param(IS_RTC_TAMPER_TRIGGER(sTamper->Trigger));
assert_param(IS_RTC_TAMPER_FILTER(sTamper->Filter));
assert_param(IS_RTC_TAMPER_SAMPLING_FREQ(sTamper->SamplingFrequency));
assert_param(IS_RTC_TAMPER_PRECHARGE_DURATION(sTamper->PrechargeDuration));
assert_param(IS_RTC_TAMPER_PULLUP_STATE(sTamper->TamperPullUp));
assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sTamper->TimeStampOnTamperDetection));
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
/* Configure the tamper trigger */
if(sTamper->Trigger != RTC_TAMPERTRIGGER_RISINGEDGE)
{
sTamper->Trigger = (uint32_t)(sTamper->Tamper << 1U);
}
tmpreg = ((uint32_t)sTamper->Tamper | (uint32_t)sTamper->Trigger | (uint32_t)sTamper->Filter |\
(uint32_t)sTamper->SamplingFrequency | (uint32_t)sTamper->PrechargeDuration |\
(uint32_t)sTamper->TamperPullUp | sTamper->TimeStampOnTamperDetection);
hrtc->Instance->TAFCR &= (uint32_t)~((uint32_t)sTamper->Tamper | (uint32_t)(sTamper->Tamper << 1U) | (uint32_t)RTC_TAFCR_TAMPTS |\
(uint32_t)RTC_TAFCR_TAMPFREQ | (uint32_t)RTC_TAFCR_TAMPFLT | (uint32_t)RTC_TAFCR_TAMPPRCH |\
(uint32_t)RTC_TAFCR_TAMPPUDIS);
hrtc->Instance->TAFCR |= tmpreg;
/* Configure the Tamper Interrupt in the RTC_TAFCR */
hrtc->Instance->TAFCR |= (uint32_t)RTC_TAFCR_TAMPIE;
/* RTC Tamper Interrupt Configuration: EXTI configuration */
__HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_IT();
__HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_RISING_EDGE();
hrtc->State = HAL_RTC_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_OK;
}
/**
* @brief Deactivate Tamper.
* @param hrtc RTC handle
* @param Tamper Selected tamper pin.
* This parameter can be any combination of RTC_TAMPER_1, RTC_TAMPER_2 and RTC_TAMPER_3.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_DeactivateTamper(RTC_HandleTypeDef *hrtc, uint32_t Tamper)
{
assert_param(IS_RTC_TAMPER(Tamper));
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
/* Disable the selected Tamper pin */
hrtc->Instance->TAFCR &= (uint32_t)~Tamper;
hrtc->State = HAL_RTC_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_OK;
}
/**
* @brief Handle TimeStamp interrupt request.
* @param hrtc RTC handle
* @retval None
*/
void HAL_RTCEx_TamperTimeStampIRQHandler(RTC_HandleTypeDef *hrtc)
{
/* Get the TimeStamp interrupt source enable status */
if(__HAL_RTC_TIMESTAMP_GET_IT_SOURCE(hrtc, RTC_IT_TS) != RESET)
{
/* Get the pending status of the TIMESTAMP Interrupt */
if(__HAL_RTC_TIMESTAMP_GET_FLAG(hrtc, RTC_FLAG_TSF) != RESET)
{
/* TIMESTAMP callback */
HAL_RTCEx_TimeStampEventCallback(hrtc);
/* Clear the TIMESTAMP interrupt pending bit */
__HAL_RTC_TIMESTAMP_CLEAR_FLAG(hrtc, RTC_FLAG_TSF);
}
}
/* Get the Tamper interrupts source enable status */
if(__HAL_RTC_TAMPER_GET_IT_SOURCE(hrtc, RTC_IT_TAMP))
{
/* Get the pending status of the Tamper1 Interrupt */
if(__HAL_RTC_TAMPER_GET_FLAG(hrtc, RTC_FLAG_TAMP1F) != RESET)
{
/* Tamper1 callback */
HAL_RTCEx_Tamper1EventCallback(hrtc);
/* Clear the Tamper1 interrupt pending bit */
__HAL_RTC_TAMPER_CLEAR_FLAG(hrtc, RTC_FLAG_TAMP1F);
}
}
/* Get the Tamper interrupts source enable status */
if(__HAL_RTC_TAMPER_GET_IT_SOURCE(hrtc, RTC_IT_TAMP))
{
/* Get the pending status of the Tamper2 Interrupt */
if(__HAL_RTC_TAMPER_GET_FLAG(hrtc, RTC_FLAG_TAMP2F) != RESET)
{
/* Tamper2 callback */
HAL_RTCEx_Tamper2EventCallback(hrtc);
/* Clear the Tamper2 interrupt pending bit */
__HAL_RTC_TAMPER_CLEAR_FLAG(hrtc, RTC_FLAG_TAMP2F);
}
}
#if defined(STM32F071xB) || defined(STM32F072xB) || defined(STM32F078xx) || defined(STM32F091xC) || defined(STM32F098xx)
/* Get the Tamper interrupts source enable status */
if(__HAL_RTC_TAMPER_GET_IT_SOURCE(hrtc, RTC_IT_TAMP))
{
/* Get the pending status of the Tamper3 Interrupt */
if(__HAL_RTC_TAMPER_GET_FLAG(hrtc, RTC_FLAG_TAMP3F) != RESET)
{
/* Tamper3 callback */
HAL_RTCEx_Tamper3EventCallback(hrtc);
/* Clear the Tamper3 interrupt pending bit */
__HAL_RTC_TAMPER_CLEAR_FLAG(hrtc, RTC_FLAG_TAMP3F);
}
}
#endif
/* Clear the EXTI's Flag for RTC TimeStamp and Tamper */
__HAL_RTC_TAMPER_TIMESTAMP_EXTI_CLEAR_FLAG();
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_READY;
}
/**
* @brief TimeStamp callback.
* @param hrtc RTC handle
* @retval None
*/
__weak void HAL_RTCEx_TimeStampEventCallback(RTC_HandleTypeDef *hrtc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hrtc);
/* NOTE : This function should not be modified, when the callback is needed,
the HAL_RTCEx_TimeStampEventCallback could be implemented in the user file
*/
}
/**
* @brief Tamper 1 callback.
* @param hrtc RTC handle
* @retval None
*/
__weak void HAL_RTCEx_Tamper1EventCallback(RTC_HandleTypeDef *hrtc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hrtc);
/* NOTE : This function should not be modified, when the callback is needed,
the HAL_RTCEx_Tamper1EventCallback could be implemented in the user file
*/
}
/**
* @brief Tamper 2 callback.
* @param hrtc RTC handle
* @retval None
*/
__weak void HAL_RTCEx_Tamper2EventCallback(RTC_HandleTypeDef *hrtc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hrtc);
/* NOTE : This function should not be modified, when the callback is needed,
the HAL_RTCEx_Tamper2EventCallback could be implemented in the user file
*/
}
#if defined(STM32F071xB) || defined(STM32F072xB) || defined(STM32F078xx) || defined(STM32F091xC) || defined(STM32F098xx)
/**
* @brief Tamper 3 callback.
* @param hrtc RTC handle
* @retval None
*/
__weak void HAL_RTCEx_Tamper3EventCallback(RTC_HandleTypeDef *hrtc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hrtc);
/* NOTE : This function should not be modified, when the callback is needed,
the HAL_RTCEx_Tamper3EventCallback could be implemented in the user file
*/
}
#endif
/**
* @brief Handle TimeStamp polling request.
* @param hrtc RTC handle
* @param Timeout Timeout duration
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_PollForTimeStampEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout)
{
uint32_t tickstart = HAL_GetTick();
while(__HAL_RTC_TIMESTAMP_GET_FLAG(hrtc, RTC_FLAG_TSF) == RESET)
{
if(__HAL_RTC_TIMESTAMP_GET_FLAG(hrtc, RTC_FLAG_TSOVF) != RESET)
{
/* Clear the TIMESTAMP OverRun Flag */
__HAL_RTC_TIMESTAMP_CLEAR_FLAG(hrtc, RTC_FLAG_TSOVF);
/* Change TIMESTAMP state */
hrtc->State = HAL_RTC_STATE_ERROR;
return HAL_ERROR;
}
if(Timeout != HAL_MAX_DELAY)
{
if((Timeout == 0U) || ((HAL_GetTick() - tickstart) > Timeout))
{
hrtc->State = HAL_RTC_STATE_TIMEOUT;
return HAL_TIMEOUT;
}
}
}
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_READY;
return HAL_OK;
}
/**
* @brief Handle Tamper 1 Polling.
* @param hrtc RTC handle
* @param Timeout Timeout duration
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_PollForTamper1Event(RTC_HandleTypeDef *hrtc, uint32_t Timeout)
{
uint32_t tickstart = HAL_GetTick();
/* Get the status of the Interrupt */
while(__HAL_RTC_TAMPER_GET_FLAG(hrtc,RTC_FLAG_TAMP1F)== RESET)
{
if(Timeout != HAL_MAX_DELAY)
{
if((Timeout == 0U) || ((HAL_GetTick() - tickstart) > Timeout))
{
hrtc->State = HAL_RTC_STATE_TIMEOUT;
return HAL_TIMEOUT;
}
}
}
/* Clear the Tamper Flag */
__HAL_RTC_TAMPER_CLEAR_FLAG(hrtc,RTC_FLAG_TAMP1F);
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_READY;
return HAL_OK;
}
/**
* @brief Handle Tamper 2 Polling.
* @param hrtc RTC handle
* @param Timeout Timeout duration
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_PollForTamper2Event(RTC_HandleTypeDef *hrtc, uint32_t Timeout)
{
uint32_t tickstart = HAL_GetTick();
/* Get the status of the Interrupt */
while(__HAL_RTC_TAMPER_GET_FLAG(hrtc,RTC_FLAG_TAMP2F) == RESET)
{
if(Timeout != HAL_MAX_DELAY)
{
if((Timeout == 0U) || ((HAL_GetTick() - tickstart) > Timeout))
{
hrtc->State = HAL_RTC_STATE_TIMEOUT;
return HAL_TIMEOUT;
}
}
}
/* Clear the Tamper Flag */
__HAL_RTC_TAMPER_CLEAR_FLAG(hrtc,RTC_FLAG_TAMP2F);
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_READY;
return HAL_OK;
}
#if defined(STM32F071xB) || defined(STM32F072xB) || defined(STM32F078xx) || defined(STM32F091xC) || defined(STM32F098xx)
/**
* @brief Handle Tamper 3 Polling.
* @param hrtc RTC handle
* @param Timeout Timeout duration
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_PollForTamper3Event(RTC_HandleTypeDef *hrtc, uint32_t Timeout)
{
uint32_t tickstart = HAL_GetTick();
/* Get the status of the Interrupt */
while(__HAL_RTC_TAMPER_GET_FLAG(hrtc,RTC_FLAG_TAMP3F) == RESET)
{
if(Timeout != HAL_MAX_DELAY)
{
if((Timeout == 0U) || ((HAL_GetTick() - tickstart) > Timeout))
{
hrtc->State = HAL_RTC_STATE_TIMEOUT;
return HAL_TIMEOUT;
}
}
}
/* Clear the Tamper Flag */
__HAL_RTC_TAMPER_CLEAR_FLAG(hrtc,RTC_FLAG_TAMP3F);
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_READY;
return HAL_OK;
}
#endif
/**
* @}
*/
#if defined(STM32F070xB) || defined(STM32F071xB) || defined(STM32F072xB) || defined(STM32F078xx) || defined(STM32F091xC) || defined(STM32F098xx) || defined(STM32F030xC)
/** @addtogroup RTCEx_Exported_Functions_Group2
* @brief RTC Wake-up functions
*
@verbatim
===============================================================================
##### RTC Wake-up functions #####
===============================================================================
[..] This section provides functions allowing to configure Wake-up feature
@endverbatim
* @{
*/
/**
* @brief Set wake up timer.
* @param hrtc RTC handle
* @param WakeUpCounter Wake up counter
* @param WakeUpClock Wake up clock
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_SetWakeUpTimer(RTC_HandleTypeDef *hrtc, uint32_t WakeUpCounter, uint32_t WakeUpClock)
{
uint32_t tickstart = 0U;
/* Check the parameters */
assert_param(IS_RTC_WAKEUP_CLOCK(WakeUpClock));
assert_param(IS_RTC_WAKEUP_COUNTER(WakeUpCounter));
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
/*Check RTC WUTWF flag is reset only when wake up timer enabled*/
if((hrtc->Instance->CR & RTC_CR_WUTE) != RESET){
tickstart = HAL_GetTick();
/* Wait till RTC WUTWF flag is reset and if Time out is reached exit */
while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTWF) == SET)
{
if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE)
{
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
hrtc->State = HAL_RTC_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_TIMEOUT;
}
}
}
__HAL_RTC_WAKEUPTIMER_DISABLE(hrtc);
tickstart = HAL_GetTick();
/* Wait till RTC WUTWF flag is set and if Time out is reached exit */
while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTWF) == RESET)
{
if((HAL_GetTick()-tickstart) > RTC_TIMEOUT_VALUE)
{
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
hrtc->State = HAL_RTC_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_TIMEOUT;
}
}
/* Clear the Wakeup Timer clock source bits in CR register */
hrtc->Instance->CR &= (uint32_t)~RTC_CR_WUCKSEL;
/* Configure the clock source */
hrtc->Instance->CR |= (uint32_t)WakeUpClock;
/* Configure the Wakeup Timer counter */
hrtc->Instance->WUTR = (uint32_t)WakeUpCounter;
/* Enable the Wakeup Timer */
__HAL_RTC_WAKEUPTIMER_ENABLE(hrtc);
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
hrtc->State = HAL_RTC_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_OK;
}
/**
* @brief Set wake up timer with interrupt.
* @param hrtc RTC handle
* @param WakeUpCounter Wake up counter
* @param WakeUpClock Wake up clock
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_SetWakeUpTimer_IT(RTC_HandleTypeDef *hrtc, uint32_t WakeUpCounter, uint32_t WakeUpClock)
{
uint32_t tickstart = 0U;
/* Check the parameters */
assert_param(IS_RTC_WAKEUP_CLOCK(WakeUpClock));
assert_param(IS_RTC_WAKEUP_COUNTER(WakeUpCounter));
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
/*Check RTC WUTWF flag is reset only when wake up timer enabled*/
if((hrtc->Instance->CR & RTC_CR_WUTE) != RESET){
tickstart = HAL_GetTick();
/* Wait till RTC WUTWF flag is reset and if Time out is reached exit */
while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTWF) == SET)
{
if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE)
{
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
hrtc->State = HAL_RTC_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_TIMEOUT;
}
}
}
/* Disable the Wake-Up timer */
__HAL_RTC_WAKEUPTIMER_DISABLE(hrtc);
/* Clear flag Wake-Up */
__HAL_RTC_WAKEUPTIMER_CLEAR_FLAG(hrtc, RTC_FLAG_WUTF);
tickstart = HAL_GetTick();
/* Wait till RTC WUTWF flag is set and if Time out is reached exit */
while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTWF) == RESET)
{
if((HAL_GetTick()-tickstart) > RTC_TIMEOUT_VALUE)
{
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
hrtc->State = HAL_RTC_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_TIMEOUT;
}
}
/* Configure the Wakeup Timer counter */
hrtc->Instance->WUTR = (uint32_t)WakeUpCounter;
/* Clear the Wakeup Timer clock source bits in CR register */
hrtc->Instance->CR &= (uint32_t)~RTC_CR_WUCKSEL;
/* Configure the clock source */
hrtc->Instance->CR |= (uint32_t)WakeUpClock;
/* RTC WakeUpTimer Interrupt Configuration: EXTI configuration */
__HAL_RTC_WAKEUPTIMER_EXTI_ENABLE_IT();
__HAL_RTC_WAKEUPTIMER_EXTI_ENABLE_RISING_EDGE();
/* Configure the Interrupt in the RTC_CR register */
__HAL_RTC_WAKEUPTIMER_ENABLE_IT(hrtc,RTC_IT_WUT);
/* Enable the Wakeup Timer */
__HAL_RTC_WAKEUPTIMER_ENABLE(hrtc);
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
hrtc->State = HAL_RTC_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_OK;
}
/**
* @brief Deactivate wake up timer counter.
* @param hrtc RTC handle
* @retval HAL status
*/
uint32_t HAL_RTCEx_DeactivateWakeUpTimer(RTC_HandleTypeDef *hrtc)
{
uint32_t tickstart = 0U;
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
/* Disable the Wakeup Timer */
__HAL_RTC_WAKEUPTIMER_DISABLE(hrtc);
/* In case of interrupt mode is used, the interrupt source must disabled */
__HAL_RTC_WAKEUPTIMER_DISABLE_IT(hrtc,RTC_IT_WUT);
tickstart = HAL_GetTick();
/* Wait till RTC WUTWF flag is set and if Time out is reached exit */
while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTWF) == RESET)
{
if((HAL_GetTick()-tickstart) > RTC_TIMEOUT_VALUE)
{
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
hrtc->State = HAL_RTC_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_TIMEOUT;
}
}
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
hrtc->State = HAL_RTC_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_OK;
}
/**
* @brief Get wake up timer counter.
* @param hrtc RTC handle
* @retval Counter value
*/
uint32_t HAL_RTCEx_GetWakeUpTimer(RTC_HandleTypeDef *hrtc)
{
/* Get the counter value */
return ((uint32_t)(hrtc->Instance->WUTR & RTC_WUTR_WUT));
}
/**
* @brief Handle Wake Up Timer interrupt request.
* @param hrtc RTC handle
* @retval None
*/
void HAL_RTCEx_WakeUpTimerIRQHandler(RTC_HandleTypeDef *hrtc)
{
/* Get the WAKEUPTIMER interrupt source enable status */
if(__HAL_RTC_WAKEUPTIMER_GET_IT_SOURCE(hrtc, RTC_IT_WUT) != RESET)
{
/* Get the pending status of the WAKEUPTIMER Interrupt */
if(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTF) != RESET)
{
/* WAKEUPTIMER callback */
HAL_RTCEx_WakeUpTimerEventCallback(hrtc);
/* Clear the WAKEUPTIMER interrupt pending bit */
__HAL_RTC_WAKEUPTIMER_CLEAR_FLAG(hrtc, RTC_FLAG_WUTF);
}
}
/* Clear the EXTI's line Flag for RTC WakeUpTimer */
__HAL_RTC_WAKEUPTIMER_EXTI_CLEAR_FLAG();
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_READY;
}
/**
* @brief Wake Up Timer callback.
* @param hrtc RTC handle
* @retval None
*/
__weak void HAL_RTCEx_WakeUpTimerEventCallback(RTC_HandleTypeDef *hrtc)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hrtc);
/* NOTE : This function should not be modified, when the callback is needed,
the HAL_RTCEx_WakeUpTimerEventCallback could be implemented in the user file
*/
}
/**
* @brief Handle Wake Up Timer Polling.
* @param hrtc RTC handle
* @param Timeout Timeout duration
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_PollForWakeUpTimerEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout)
{
uint32_t tickstart = HAL_GetTick();
while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTF) == RESET)
{
if(Timeout != HAL_MAX_DELAY)
{
if((Timeout == 0U)||((HAL_GetTick() - tickstart ) > Timeout))
{
hrtc->State = HAL_RTC_STATE_TIMEOUT;
return HAL_TIMEOUT;
}
}
}
/* Clear the WAKEUPTIMER Flag */
__HAL_RTC_WAKEUPTIMER_CLEAR_FLAG(hrtc, RTC_FLAG_WUTF);
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_READY;
return HAL_OK;
}
/**
* @}
*/
#endif /* defined(STM32F070xB) || defined(STM32F071xB) || defined(STM32F072xB) || defined(STM32F078xx) || defined(STM32F091xC) || defined(STM32F098xx) | defined(STM32F030xC) */
/** @addtogroup RTCEx_Exported_Functions_Group3
* @brief Extended Peripheral Control functions
*
@verbatim
===============================================================================
##### Extended Peripheral Control functions #####
===============================================================================
[..]
This subsection provides functions allowing to
(+) Write a data in a specified RTC Backup data register
(+) Read a data in a specified RTC Backup data register
(+) Set the Coarse calibration parameters.
(+) Deactivate the Coarse calibration parameters
(+) Set the Smooth calibration parameters.
(+) Configure the Synchronization Shift Control Settings.
(+) Configure the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz).
(+) Deactivate the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz).
(+) Enable the RTC reference clock detection.
(+) Disable the RTC reference clock detection.
(+) Enable the Bypass Shadow feature.
(+) Disable the Bypass Shadow feature.
@endverbatim
* @{
*/
#if !defined(STM32F030x6) && !defined(STM32F030x8) && !defined(STM32F070x6) && !defined(STM32F070xB) && !defined(STM32F030xC)
/**
* @brief Write a data in a specified RTC Backup data register.
* @param hrtc RTC handle
* @param BackupRegister RTC Backup data Register number.
* This parameter can be: RTC_BKP_DRx where x can be from 0 to 4 to
* specify the register.
* @param Data Data to be written in the specified RTC Backup data register.
* @retval None
*/
void HAL_RTCEx_BKUPWrite(RTC_HandleTypeDef *hrtc, uint32_t BackupRegister, uint32_t Data)
{
uint32_t tmp = 0U;
/* Check the parameters */
assert_param(IS_RTC_BKP(BackupRegister));
tmp = (uint32_t)&(hrtc->Instance->BKP0R);
tmp += (BackupRegister * 4U);
/* Write the specified register */
*(__IO uint32_t *)tmp = (uint32_t)Data;
}
/**
* @brief Reads data from the specified RTC Backup data Register.
* @param hrtc RTC handle
* @param BackupRegister RTC Backup data Register number.
* This parameter can be: RTC_BKP_DRx where x can be from 0 to 4 to
* specify the register.
* @retval Read value
*/
uint32_t HAL_RTCEx_BKUPRead(RTC_HandleTypeDef *hrtc, uint32_t BackupRegister)
{
uint32_t tmp = 0U;
/* Check the parameters */
assert_param(IS_RTC_BKP(BackupRegister));
tmp = (uint32_t)&(hrtc->Instance->BKP0R);
tmp += (BackupRegister * 4U);
/* Read the specified register */
return (*(__IO uint32_t *)tmp);
}
#endif /* !defined(STM32F030x6) && !defined(STM32F030x8) && !defined(STM32F070x6) && !defined(STM32F070xB) && !defined(STM32F030xC) */
/**
* @brief Set the Smooth calibration parameters.
* @param hrtc RTC handle
* @param SmoothCalibPeriod Select the Smooth Calibration Period.
* This parameter can be can be one of the following values :
* @arg RTC_SMOOTHCALIB_PERIOD_32SEC: The smooth calibration period is 32s.
* @arg RTC_SMOOTHCALIB_PERIOD_16SEC: The smooth calibration period is 16s.
* @arg RTC_SMOOTHCALIB_PERIOD_8SEC: The smooth calibration period is 8s.
* @param SmoothCalibPlusPulses Select to Set or reset the CALP bit.
* This parameter can be one of the following values:
* @arg RTC_SMOOTHCALIB_PLUSPULSES_SET: Add one RTCCLK pulse every 2*11 pulses.
* @arg RTC_SMOOTHCALIB_PLUSPULSES_RESET: No RTCCLK pulses are added.
* @param SmoothCalibMinusPulsesValue Select the value of CALM[8:0] bits.
* This parameter can be one any value from 0 to 0x000001FF.
* @note To deactivate the smooth calibration, the field SmoothCalibPlusPulses
* must be equal to SMOOTHCALIB_PLUSPULSES_RESET and the field
* SmoothCalibMinusPulsesValue mut be equal to 0.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_SetSmoothCalib(RTC_HandleTypeDef* hrtc, uint32_t SmoothCalibPeriod, uint32_t SmoothCalibPlusPulses, uint32_t SmoothCalibMinusPulsesValue)
{
uint32_t tickstart = 0U;
/* Check the parameters */
assert_param(IS_RTC_SMOOTH_CALIB_PERIOD(SmoothCalibPeriod));
assert_param(IS_RTC_SMOOTH_CALIB_PLUS(SmoothCalibPlusPulses));
assert_param(IS_RTC_SMOOTH_CALIB_MINUS(SmoothCalibMinusPulsesValue));
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
/* check if a calibration is pending*/
if((hrtc->Instance->ISR & RTC_ISR_RECALPF) != RESET)
{
tickstart = HAL_GetTick();
/* check if a calibration is pending*/
while((hrtc->Instance->ISR & RTC_ISR_RECALPF) != RESET)
{
if((HAL_GetTick()-tickstart) > RTC_TIMEOUT_VALUE)
{
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_TIMEOUT;
}
}
}
/* Configure the Smooth calibration settings */
hrtc->Instance->CALR = (uint32_t)((uint32_t)SmoothCalibPeriod | (uint32_t)SmoothCalibPlusPulses | (uint32_t)SmoothCalibMinusPulsesValue);
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_OK;
}
/**
* @brief Configure the Synchronization Shift Control Settings.
* @note When REFCKON is set, firmware must not write to Shift control register.
* @param hrtc RTC handle
* @param ShiftAdd1S Select to add or not 1 second to the time calendar.
* This parameter can be one of the following values :
* @arg RTC_SHIFTADD1S_SET: Add one second to the clock calendar.
* @arg RTC_SHIFTADD1S_RESET: No effect.
* @param ShiftSubFS Select the number of Second Fractions to substitute.
* This parameter can be one any value from 0 to 0x7FFF.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_SetSynchroShift(RTC_HandleTypeDef* hrtc, uint32_t ShiftAdd1S, uint32_t ShiftSubFS)
{
uint32_t tickstart = 0U;
/* Check the parameters */
assert_param(IS_RTC_SHIFT_ADD1S(ShiftAdd1S));
assert_param(IS_RTC_SHIFT_SUBFS(ShiftSubFS));
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
tickstart = HAL_GetTick();
/* Wait until the shift is completed*/
while((hrtc->Instance->ISR & RTC_ISR_SHPF) != RESET)
{
if((HAL_GetTick()-tickstart) > RTC_TIMEOUT_VALUE)
{
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
hrtc->State = HAL_RTC_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_TIMEOUT;
}
}
/* Check if the reference clock detection is disabled */
if((hrtc->Instance->CR & RTC_CR_REFCKON) == RESET)
{
/* Configure the Shift settings */
hrtc->Instance->SHIFTR = (uint32_t)(uint32_t)(ShiftSubFS) | (uint32_t)(ShiftAdd1S);
/* If RTC_CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */
if((hrtc->Instance->CR & RTC_CR_BYPSHAD) == RESET)
{
if(HAL_RTC_WaitForSynchro(hrtc) != HAL_OK)
{
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
hrtc->State = HAL_RTC_STATE_ERROR;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_ERROR;
}
}
}
else
{
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_ERROR;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_ERROR;
}
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_OK;
}
/**
* @brief Configure the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz).
* @param hrtc RTC handle
* @param CalibOutput Select the Calibration output Selection .
* This parameter can be one of the following values:
* @arg RTC_CALIBOUTPUT_512HZ: A signal has a regular waveform at 512Hz.
* @arg RTC_CALIBOUTPUT_1HZ: A signal has a regular waveform at 1Hz.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_SetCalibrationOutPut(RTC_HandleTypeDef* hrtc, uint32_t CalibOutput)
{
/* Check the parameters */
assert_param(IS_RTC_CALIB_OUTPUT(CalibOutput));
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
/* Clear flags before config */
hrtc->Instance->CR &= (uint32_t)~RTC_CR_COSEL;
/* Configure the RTC_CR register */
hrtc->Instance->CR |= (uint32_t)CalibOutput;
__HAL_RTC_CALIBRATION_OUTPUT_ENABLE(hrtc);
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_OK;
}
/**
* @brief Deactivate the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz).
* @param hrtc RTC handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_DeactivateCalibrationOutPut(RTC_HandleTypeDef* hrtc)
{
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
__HAL_RTC_CALIBRATION_OUTPUT_DISABLE(hrtc);
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_OK;
}
/**
* @brief Enable the RTC reference clock detection.
* @param hrtc RTC handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_SetRefClock(RTC_HandleTypeDef* hrtc)
{
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
/* Set Initialization mode */
if(RTC_EnterInitMode(hrtc) != HAL_OK)
{
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
/* Set RTC state*/
hrtc->State = HAL_RTC_STATE_ERROR;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_ERROR;
}
else
{
__HAL_RTC_CLOCKREF_DETECTION_ENABLE(hrtc);
/* Exit Initialization mode */
hrtc->Instance->ISR &= (uint32_t)~RTC_ISR_INIT;
}
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_OK;
}
/**
* @brief Disable the RTC reference clock detection.
* @param hrtc RTC handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_DeactivateRefClock(RTC_HandleTypeDef* hrtc)
{
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
/* Set Initialization mode */
if(RTC_EnterInitMode(hrtc) != HAL_OK)
{
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
/* Set RTC state*/
hrtc->State = HAL_RTC_STATE_ERROR;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_ERROR;
}
else
{
__HAL_RTC_CLOCKREF_DETECTION_DISABLE(hrtc);
/* Exit Initialization mode */
hrtc->Instance->ISR &= (uint32_t)~RTC_ISR_INIT;
}
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_OK;
}
/**
* @brief Enable the Bypass Shadow feature.
* @param hrtc RTC handle
* @note When the Bypass Shadow is enabled the calendar value are taken
* directly from the Calendar counter.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_EnableBypassShadow(RTC_HandleTypeDef* hrtc)
{
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
/* Set the BYPSHAD bit */
hrtc->Instance->CR |= (uint8_t)RTC_CR_BYPSHAD;
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_OK;
}
/**
* @brief Disable the Bypass Shadow feature.
* @param hrtc RTC handle
* @note When the Bypass Shadow is enabled the calendar value are taken
* directly from the Calendar counter.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RTCEx_DisableBypassShadow(RTC_HandleTypeDef* hrtc)
{
/* Process Locked */
__HAL_LOCK(hrtc);
hrtc->State = HAL_RTC_STATE_BUSY;
/* Disable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
/* Reset the BYPSHAD bit */
hrtc->Instance->CR &= ((uint8_t)~RTC_CR_BYPSHAD);
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
/* Change RTC state */
hrtc->State = HAL_RTC_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hrtc);
return HAL_OK;
}
/**
* @}
*/
/**
* @}
*/
#endif /* HAL_RTC_MODULE_ENABLED */
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
Reference in New Issue View Git Blame Copy Permalink