291 lines
9.5 KiB
C
291 lines
9.5 KiB
C
/**
|
|
******************************************************************************
|
|
* @file stm32f0xx_hal_pwr_ex.c
|
|
* @author MCD Application Team
|
|
* @brief Extended PWR HAL module driver.
|
|
* This file provides firmware functions to manage the following
|
|
* functionalities of the Power Controller (PWR) peripheral:
|
|
* + Extended Initialization and de-initialization functions
|
|
* + Extended Peripheral Control functions
|
|
*
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without modification,
|
|
* are permitted provided that the following conditions are met:
|
|
* 1. Redistributions of source code must retain the above copyright notice,
|
|
* this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright notice,
|
|
* this list of conditions and the following disclaimer in the documentation
|
|
* and/or other materials provided with the distribution.
|
|
* 3. Neither the name of STMicroelectronics nor the names of its contributors
|
|
* may be used to endorse or promote products derived from this software
|
|
* without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
|
|
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
|
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
|
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
|
|
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
|
|
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
|
|
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*
|
|
******************************************************************************
|
|
*/
|
|
|
|
/* Includes ------------------------------------------------------------------*/
|
|
#include "stm32f0xx_hal.h"
|
|
|
|
/** @addtogroup STM32F0xx_HAL_Driver
|
|
* @{
|
|
*/
|
|
|
|
/** @defgroup PWREx PWREx
|
|
* @brief PWREx HAL module driver
|
|
* @{
|
|
*/
|
|
|
|
#ifdef HAL_PWR_MODULE_ENABLED
|
|
|
|
/* Private typedef -----------------------------------------------------------*/
|
|
/* Private define ------------------------------------------------------------*/
|
|
/** @defgroup PWREx_Private_Constants PWREx Private Constants
|
|
* @{
|
|
*/
|
|
#define PVD_MODE_IT (0x00010000U)
|
|
#define PVD_MODE_EVT (0x00020000U)
|
|
#define PVD_RISING_EDGE (0x00000001U)
|
|
#define PVD_FALLING_EDGE (0x00000002U)
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/* Private macro -------------------------------------------------------------*/
|
|
/* Private variables ---------------------------------------------------------*/
|
|
/* Private function prototypes -----------------------------------------------*/
|
|
/* Exported functions ---------------------------------------------------------*/
|
|
|
|
/** @defgroup PWREx_Exported_Functions PWREx Exported Functions
|
|
* @{
|
|
*/
|
|
|
|
/** @defgroup PWREx_Exported_Functions_Group1 Peripheral Extended Control Functions
|
|
* @brief Extended Peripheral Control functions
|
|
*
|
|
@verbatim
|
|
|
|
===============================================================================
|
|
##### Peripheral extended control functions #####
|
|
===============================================================================
|
|
|
|
*** PVD configuration ***
|
|
=========================
|
|
[..]
|
|
(+) The PVD is used to monitor the VDD power supply by comparing it to a
|
|
threshold selected by the PVD Level (PLS[2:0] bits in the PWR_CR).
|
|
(+) A PVDO flag is available to indicate if VDD/VDDA is higher or lower
|
|
than the PVD threshold. This event is internally connected to the EXTI
|
|
line16 and can generate an interrupt if enabled. This is done through
|
|
HAL_PWR_ConfigPVD(), HAL_PWR_EnablePVD() functions.
|
|
(+) The PVD is stopped in Standby mode.
|
|
-@- PVD is not available on STM32F030x4/x6/x8
|
|
|
|
*** VDDIO2 Monitor Configuration ***
|
|
====================================
|
|
[..]
|
|
(+) VDDIO2 monitor is used to monitor the VDDIO2 power supply by comparing it
|
|
to VREFInt Voltage
|
|
(+) This monitor is internally connected to the EXTI line31
|
|
and can generate an interrupt if enabled. This is done through
|
|
HAL_PWREx_EnableVddio2Monitor() function.
|
|
-@- VDDIO2 is available on STM32F07x/09x/04x
|
|
|
|
@endverbatim
|
|
* @{
|
|
*/
|
|
|
|
#if defined (STM32F031x6) || defined (STM32F051x8) || \
|
|
defined (STM32F071xB) || defined (STM32F091xC) || \
|
|
defined (STM32F042x6) || defined (STM32F072xB)
|
|
/**
|
|
* @brief Configures the voltage threshold detected by the Power Voltage Detector(PVD).
|
|
* @param sConfigPVD pointer to an PWR_PVDTypeDef structure that contains the configuration
|
|
* information for the PVD.
|
|
* @note Refer to the electrical characteristics of your device datasheet for
|
|
* more details about the voltage threshold corresponding to each
|
|
* detection level.
|
|
* @retval None
|
|
*/
|
|
void HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD)
|
|
{
|
|
/* Check the parameters */
|
|
assert_param(IS_PWR_PVD_LEVEL(sConfigPVD->PVDLevel));
|
|
assert_param(IS_PWR_PVD_MODE(sConfigPVD->Mode));
|
|
|
|
/* Set PLS[7:5] bits according to PVDLevel value */
|
|
MODIFY_REG(PWR->CR, PWR_CR_PLS, sConfigPVD->PVDLevel);
|
|
|
|
/* Clear any previous config. Keep it clear if no event or IT mode is selected */
|
|
__HAL_PWR_PVD_EXTI_DISABLE_EVENT();
|
|
__HAL_PWR_PVD_EXTI_DISABLE_IT();
|
|
__HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE();
|
|
|
|
/* Configure interrupt mode */
|
|
if((sConfigPVD->Mode & PVD_MODE_IT) == PVD_MODE_IT)
|
|
{
|
|
__HAL_PWR_PVD_EXTI_ENABLE_IT();
|
|
}
|
|
|
|
/* Configure event mode */
|
|
if((sConfigPVD->Mode & PVD_MODE_EVT) == PVD_MODE_EVT)
|
|
{
|
|
__HAL_PWR_PVD_EXTI_ENABLE_EVENT();
|
|
}
|
|
|
|
/* Configure the edge */
|
|
if((sConfigPVD->Mode & PVD_RISING_EDGE) == PVD_RISING_EDGE)
|
|
{
|
|
__HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE();
|
|
}
|
|
|
|
if((sConfigPVD->Mode & PVD_FALLING_EDGE) == PVD_FALLING_EDGE)
|
|
{
|
|
__HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE();
|
|
}
|
|
}
|
|
|
|
/**
|
|
* @brief Enables the Power Voltage Detector(PVD).
|
|
* @retval None
|
|
*/
|
|
void HAL_PWR_EnablePVD(void)
|
|
{
|
|
PWR->CR |= (uint32_t)PWR_CR_PVDE;
|
|
}
|
|
|
|
/**
|
|
* @brief Disables the Power Voltage Detector(PVD).
|
|
* @retval None
|
|
*/
|
|
void HAL_PWR_DisablePVD(void)
|
|
{
|
|
PWR->CR &= ~((uint32_t)PWR_CR_PVDE);
|
|
}
|
|
|
|
/**
|
|
* @brief This function handles the PWR PVD interrupt request.
|
|
* @note This API should be called under the PVD_IRQHandler() or PVD_VDDIO2_IRQHandler().
|
|
* @retval None
|
|
*/
|
|
void HAL_PWR_PVD_IRQHandler(void)
|
|
{
|
|
/* Check PWR exti flag */
|
|
if(__HAL_PWR_PVD_EXTI_GET_FLAG() != RESET)
|
|
{
|
|
/* PWR PVD interrupt user callback */
|
|
HAL_PWR_PVDCallback();
|
|
|
|
/* Clear PWR Exti pending bit */
|
|
__HAL_PWR_PVD_EXTI_CLEAR_FLAG();
|
|
}
|
|
}
|
|
|
|
/**
|
|
* @brief PWR PVD interrupt callback
|
|
* @retval None
|
|
*/
|
|
__weak void HAL_PWR_PVDCallback(void)
|
|
{
|
|
/* NOTE : This function Should not be modified, when the callback is needed,
|
|
the HAL_PWR_PVDCallback could be implemented in the user file
|
|
*/
|
|
}
|
|
|
|
#endif /* defined (STM32F031x6) || defined (STM32F051x8) || */
|
|
/* defined (STM32F071xB) || defined (STM32F091xC) || */
|
|
/* defined (STM32F042x6) || defined (STM32F072xB) */
|
|
|
|
#if defined (STM32F042x6) || defined (STM32F048xx) || \
|
|
defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \
|
|
defined (STM32F091xC) || defined (STM32F098xx)
|
|
/**
|
|
* @brief Enable VDDIO2 monitor: enable Exti 31 and falling edge detection.
|
|
* @note If Exti 31 is enable correlty and VDDIO2 voltage goes below Vrefint,
|
|
an interrupt is generated Irq line 1.
|
|
NVIS has to be enable by user.
|
|
* @retval None
|
|
*/
|
|
void HAL_PWREx_EnableVddio2Monitor(void)
|
|
{
|
|
__HAL_PWR_VDDIO2_EXTI_ENABLE_IT();
|
|
__HAL_PWR_VDDIO2_EXTI_ENABLE_FALLING_EDGE();
|
|
}
|
|
|
|
/**
|
|
* @brief Disable the Vddio2 Monitor.
|
|
* @retval None
|
|
*/
|
|
void HAL_PWREx_DisableVddio2Monitor(void)
|
|
{
|
|
__HAL_PWR_VDDIO2_EXTI_DISABLE_IT();
|
|
__HAL_PWR_VDDIO2_EXTI_DISABLE_FALLING_EDGE();
|
|
|
|
}
|
|
|
|
/**
|
|
* @brief This function handles the PWR Vddio2 monitor interrupt request.
|
|
* @note This API should be called under the VDDIO2_IRQHandler() PVD_VDDIO2_IRQHandler().
|
|
* @retval None
|
|
*/
|
|
void HAL_PWREx_Vddio2Monitor_IRQHandler(void)
|
|
{
|
|
/* Check PWR exti flag */
|
|
if(__HAL_PWR_VDDIO2_EXTI_GET_FLAG() != RESET)
|
|
{
|
|
/* PWR Vddio2 monitor interrupt user callback */
|
|
HAL_PWREx_Vddio2MonitorCallback();
|
|
|
|
/* Clear PWR Exti pending bit */
|
|
__HAL_PWR_VDDIO2_EXTI_CLEAR_FLAG();
|
|
}
|
|
}
|
|
|
|
/**
|
|
* @brief PWR Vddio2 Monitor interrupt callback
|
|
* @retval None
|
|
*/
|
|
__weak void HAL_PWREx_Vddio2MonitorCallback(void)
|
|
{
|
|
/* NOTE : This function Should not be modified, when the callback is needed,
|
|
the HAL_PWREx_Vddio2MonitorCallback could be implemented in the user file
|
|
*/
|
|
}
|
|
|
|
#endif /* defined (STM32F042x6) || defined (STM32F048xx) || \
|
|
defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \
|
|
defined (STM32F091xC) || defined (STM32F098xx) */
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
#endif /* HAL_PWR_MODULE_ENABLED */
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|