`multistep_filt` was not configured at all on tmc2240 and tmc5160. As such, it would default to the value of 0 when the GCONF field was sent to the driver. However, that field has a default value of 1 in the driver, so klipper was overriding the defaults by accident.
This field improves the stability of velocity based thresholds (it's effectively TSTEP filtering) and it also improves the current regulation stability in stealthchop2 (according to the datasheet).
This field was already set to 1 correctly in the tmc2208/tmc2209 driver code.
Signed-off-by: Alex Voinea <voinea.dragos.alexandru@gmail.com>
Add the default base config for the Ender 3 v2 Neo (as released 2022).
This config also works with the newer D32F303 based 4.2.2 boards.
Signed-off-by: Sam McLeod <sammcj@users.noreply.github.com>
Reading an I2C device from the Linux MCU used a separate write(2)
to select the target register & read(2) to get the value(s). This
implementation uses ioctl(file, I2C_RDWR, ...) to skip a large bus idle
period and extra process sleep by combining them like the stm32.
I2C_RDRW requires I2C_FUNC_I2C flag in the I2C driver. I2C_FUNC_I2C
is defined in:
BCM2835: Pi 1 Models A, A+, B, B+, the Raspberry Pi Zero, the
Raspberry Pi Zero W, and the Raspberry Pi Compute Module 1
BCM2836: Pi 2 Model B
Identical to BCM2835 except Cortex
BCM2837: Pi 3 Model B, later models of the Raspberry Pi 2 Model B,
and the Raspberry Pi Compute Module 3
BCM2837B0: Pi 3 Models A+, B+, and the Raspberry Pi Compute Module 3+
BCM2711: Pi 4 Model B, the Raspberry Pi 400, and the Raspberry Pi
Compute Module 4
RK3xxx: Rockchips SoCs NanoPi, RockPi, Tinker, etc.
SUNXI: H2, H3, etc. Orange Pi
AMLOGIC: S905x, Banana Pi, Odroid, etc.
TEGRA: NVidia Jetson etc.
MediaTek: Several SBCs in other ranges
Signed-off-by: Matthew Swabey <matthew@swabey.org>
Purely esthetic. Make all tmc driver init code similar to one another. The various fields were grouped based on the register which they affect or the function they perform.
Signed-off-by: Alex Voinea <voinea.dragos.alexandru@gmail.com>
Previously, the globalscaler was calculated during the config parsing and set to a fixed value. If the current was changed for any reason after the initialization, only IRUN and IHOLD would be changed. This however caused issues:
- If the new current was lower, then the resolution of the possible current values would be low since there are only 32 IRUN/IHOLD steps.
- If the new current was higher, it wouldn't actually work since IRUN and IHOLD are capped at 31, so it wouldn't be possible to increase the current without increasing globalscaler.
With this commit, the globalscaler is recalculated whenever necessary in order to ensure the correct range of IRUN/IHOLD is used.
Signed-off-by: Alex Voinea <voinea.dragos.alexandru@gmail.com>
Fix filament sensor and remove unneeded config changes in extruder
The filament sensor on the printer used for initial testing had been removed prior to flashing klipper to it. Only a basic test to see it if triggered or not was preformed. It was discovered by someone else doing some testing on another printer that it would frequently pause. This was a simple oversight, assuming it was a runout switch.
Removed section of config related to filament runout switch and replaced with basic config for filament motion so they printer will simply pause when no more motion is detected. Also notated to add CLEAR_PAUSE to start gcode if using this sensor as it will trigger a paused state when loading or unloading filament. If printer is in a paused state at the start of the print, the attempt to pause will cause the printer to rapidly pause and unpause itself.
Removed min_extruder_temp and max_extrude_only_distance from the extruder section, as they were there only for macros on a test system that is not put into this sample config
Signed-off-by: Zachary Welvaert <zwelvaert@gmail.com>
The actual board name is EZBoard V2 without the lite. Renaming the file and correcting the intro text to reflect the actual board name.
Signed-off-by: Anthony Dellett <anthony.dellett@gmail.com>
This is an update to the script that looks for the new systemd service and restarts it if appropriate.
Signed-off-by: James Hartley <james@hartleyns.com>
Use mcu.lookup_command().get_command_tag() instead of
mcu.lookup_command_tag(). This improves error reporting on a protocol
mismatch. It also enables support for a msgtag that is negative.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Adds sdio support for the stm32f4 to allow for SD card flash updates
without power cycling some boards, e.g. BTT Octopus Pro.
Signed-off-by: H. Gregor Molter <gregor.molter@secretlab.de>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The recent PR to change this to say `#!/usr/bin/env python` instead of `#!/usr/bin/env python2` can cause issues on non rpi based OS's where `python` is not mapped to `python3`.
`#!/usr/bin/env python3` should work in both situations.
Signed-off-by: James Hartley <james@hartleyns.com>
Kevin O'Connor