Commit Graph

401 Commits

Author SHA1 Message Date
Florian Heilmann 383fb1dbfd config: Fix pins for E6 in generic-duet2-duex.cfg
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2019-08-07 11:01:23 -04:00
Kevin O'Connor 4c09d8bf02 dotstar: Initial support for "dotstar" LEDs
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-08-06 19:44:32 -04:00
Kevin O'Connor a730aec8bc tmc_uart: Add support for configuring the uart address on tmc2209 chips
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-31 13:02:27 -04:00
Kevin O'Connor 745a8dc0ac config: Add an example config file for the bigtreetech skr mini
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-30 21:42:20 -04:00
Kevin O'Connor a878831d5e mcp4728: Update to better match printrbot revf requirements
Reported by @Grumps49.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-26 11:02:56 -04:00
Kevin O'Connor 46041f5411 neopixel: Add support for daisy-chained chips
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-23 21:59:38 -04:00
Kevin O'Connor abf3fa4b71 neopixel: Add support for setting a default color at startup
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-23 21:59:38 -04:00
Kevin O'Connor 4d90b60fdb config: Fix example beeper pin in generic-bigtreetech-skr-v1.3.cfg
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-18 11:15:02 -04:00
Kevin O'Connor b7bc96c3b2 neopixel: Add initial support for "neopixel" leds
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-12 21:44:01 -04:00
Kevin O'Connor 25438a7901 config: Simplify generic-bigtreetech-skr-v1.3.cfg
Move the TMC2208 and TMC2130 blocks to later in the file.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-12 08:28:10 -04:00
Kevin O'Connor b2a8b0dd65 config: Update default serial setting of generic-duet2-duex.cfg
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-11 10:35:22 -04:00
Kevin O'Connor a34613cf86 config: Add a simplified Duet2 Eth/Wifi example config file
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-11 10:35:22 -04:00
Kevin O'Connor e2d8a6f02d config: Rename generic-duet2.cfg to generic-duet2-duex.cfg
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-11 10:35:22 -04:00
Kevin O'Connor 0343d0c73a firmware_retract: Remove z_hop support
The current z_hop support did not work correctly with common slicers
that change Z height between retract and unretract, and it did not
work correctly with slicers that issue a retract at the end of a print
and then at the beginning of the next print.

The z_hop support is therefore being removed until these issues can be
fixed.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-10 19:25:56 -04:00
Kevin O'Connor a477c50592 config: Heater pins are inverted on the Duet2 Maestro
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-10 13:23:59 -04:00
Arksine e19a41d0dd docs: Add documentation for [delayed_gcode]
Signed-off-by:  Eric Callahan <arksine.code@gmail.com>
2019-07-01 11:09:30 -04:00
Kevin O'Connor 02e579f578 config: Fix stepper_bed step_distance description in example-polar.cfg
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-01 11:00:37 -04:00
Arksine 57eb0e8975 docs: Update for latest changs to skew_correction
Signed-off-by:  Eric Callahan <arksine.code@gmail.com>
2019-06-29 10:58:46 -04:00
Kevin O'Connor 7947dc3389 config: Use tmc2660 virtual_enable in generic-duet2.cfg
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-28 16:59:26 -04:00
Kevin O'Connor b0c459d8bf config: Use tmc2208 virtual_enable in generic-duet2-maestro.cfg
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-28 16:59:26 -04:00
Kevin O'Connor a2e550d1cd stepper: Add support for providing a list of pins to enable
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-28 16:59:26 -04:00
Kevin O'Connor 7702f0a027 tmc: Add support for virtual enable pins
Add support for enabling the stepper via the communication channel.
This improves support for boards with a shared enable line.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-28 16:59:26 -04:00
Kevin O'Connor e5f74a64ed polar: Add initial support for multiple bed rotations
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-28 10:00:40 -04:00
Arksine a3b4543c97 skew_correction: add documentation
Signed-Off-By:  Eric Callahan <arksine.code@gmail.com>
2019-06-26 20:16:35 -04:00
Kevin O'Connor 79c24f95b3 config: Add example tmc2130 sections to SKR v1.3 board
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-25 13:49:35 -04:00
Kevin O'Connor e18dddd1ab config: No need to list all tmc drivers in endstop_phase description
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-23 12:27:09 -04:00
Kevin O'Connor 7173a2c427 config: Update example-extras.cfg for tmc2209
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-23 11:47:24 -04:00
Kevin O'Connor c3467f5b35 config: Add generic-printrboard-g2.cfg config file
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-21 23:12:31 -04:00
Alec B. Plumb daadb36cb4 gcode_button: Execute gcode when a button is pressed or released (#1745)
An extra to execute gcode when a hardware button is pressed or released. Uses the jinja2 templating system.

Inspired by pull request #545 from Miguel Moitinho miguel@moitinho.net and pull request #1098 from Paulo Drugos paulodrugos@gmail.com

Signed-off-by: Alec Plumb <alec@etherwalker.com>
2019-06-21 18:06:31 -04:00
Kevin O'Connor c92aca74b5 probe: Add support for samples_tolerance
Add a check on the maximum Z distance between probe samples.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-21 14:06:20 -04:00
Kevin O'Connor 3e741a1f88 config: Clarify which boards use lpc1768 vs lpc1769 when known
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-20 11:23:30 -04:00
Kevin O'Connor 587db5c315 tmc2660: Don't allow configuration of DEDGE
Setting DEDGE would just break the code.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-18 13:24:54 -04:00
fess 49c36f868b z_tilt: Support retries
Support retrying Z_TILT_ADJUST a configurable number of times
to a configurable tolerance both in the config or as parameters.

- By default keeps original behavior of no retries.
- Adds parameters RETRIES and RETRY_TOLERANCE to QUAD_GANTRY_LEVEL gcode.
- adds config options retries and retry_tolerance to uad_gantry_level]
- issues an error if we are getting worse intead of approaching tolerance
- issues an error if retries were requested but we did not reach the tolerance
in the specified number of retries

the minimum change should  be a single z step for those
probing 2 points for 2 stepper motors and 3 for 3 stepper motors.

at one point it was suggested to use the amount of z adjustment instead of the
range of the probed points as a trigger for retry. I've chosen not to do this.
using z adustment in these cases means the minimum unit of change is related to
the angle created by the probed points  and the distance to stepper motor and
can be more than a couple steps which is rather unintuitive.

for the case when someone is using more probed points than z steppers the
probed points range will have some fixed minimum value that can't be reduced
which is also unintuitive but that case should idealy be the rarer case, and
the user can learn to set a higher tolerance that matches their probing setup.

Signed-off-by: John "Fess" Fessenden <fess@fess.org>
2019-06-18 12:12:25 -04:00
fess bd40690bd1 quad_gantry_level: Support retries
Support retrying QUAD_GANTRY_LEVEL a configurable number of times
to a configurable tolerance both in the config or as parameters.

- By default keeps original behavior of no retries.
- Adds parameters RETRIES and RETRY_TOLERANCE to QUAD_GANTRY_LEVEL gcode.
- adds config options retries and retry_tolerance to `[quad_gantry_level]`
- issues an error if we are getting worse intead of approaching tolerance
- issues an error if retries were requested but we did not reach the tolerance
in the specified number of retries

Signed-off-by: John "Fess" Fessenden <fess@fess.org>
2019-06-18 12:12:25 -04:00
Hywelmartin 771e7b2987 config: MKS mini 12864 LCD on SKR 1.3
Signed-off-by: Martin Malmqvist <hywelmartin@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-18 10:29:11 -04:00
nzlrhyz 631c3fe052 config: Create printer-wanhao-duplicator-i3-plus-mark2-2019.cfg
Reported by @nzlrhyz.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-18 10:13:41 -04:00
Kevin O'Connor caea441edd config: Update tmc2660 block in example-extras.cfg
No need to describe the SET_TMC_CURRENT command in the
example-extras.cfg - it's describe in docs/G-Codes.md and is now
supported on all tmc drivers.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-18 09:43:13 -04:00
Kevin O'Connor 20d0bb8354 config: Update tmc5160 block in example-extras.cfg
List all the configurable parameters in the tmc5160 example block and
use similar wording as the other tmc drivers.

Also, don't allow DEDGE to be configured as it would just break the
current code.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-18 09:41:27 -04:00
Kevin O'Connor 1ee2835eed config: Add LCD settings to config/generic-duet2-maestro.cfg
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-13 11:29:55 -04:00
Kevin O'Connor c601d90b47 config: Add tmc2208 select_pins description to example-extras.cfg
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-12 23:09:56 -04:00
Kevin O'Connor 8f092b5966 config: Fix sensor_resistor in generic-duet2-maestro.cfg
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-12 22:26:44 -04:00
Kevin O'Connor e697fc11af config: Add an example config for the Duet2 Maestro
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-12 22:14:41 -04:00
Kevin O'Connor 8b00580884 gcode_macro: Parse variable_X parameters using ast.literal_eval()
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-07 19:33:31 -04:00
Kevin O'Connor 9d33ef4061 config: Update example-extras.cfg to point to Command_Templates.md
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-07 11:57:54 -04:00
Kevin O'Connor 9613cd2c8a config: Fix G90 use in sample-probe-as-z-endstop.cfg
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-07 10:37:10 -04:00
Kevin O'Connor 2b8dca5dbf probe: Move multi-sampling capability from ProbePointsHelper to Probe
This changes the config file so that the configuration of
multi-samples is now done in the [probe] (and [bltouch]) section
instead of the various delta, bed_mesh, z_tilt, etc. config sections.

With this change, PROBE and PROBE_CALIBRATE commands now also utilize
multi-sampling.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-06 10:08:58 -04:00
Len Trigg 5989f7a8a6 firmware_retraction: Implementation of tuneable G10/G11 firmware retraction (#1617)
This supports getting and setting of retraction parameters without
having to restart klippy.

Signed-off-by: Len Trigg <lenbok@gmail.com>
2019-06-06 09:10:09 -04:00
Kevin O'Connor a68f577adf gcode_macro: Add support for SET_GCODE_VARIABLE command
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-04 09:50:30 -04:00
Kevin O'Connor 3e1c42da80 thermistor: Add support for printers with an "inline_resistor"
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-02 10:59:23 -04:00
Kevin O'Connor 7f04dc46d0 config: Update M600 in sample-macros.cfg to use SAVE_GCODE_STATE
Save and restore state in the example M600 macro.  Also, add
pause_resume config section.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-31 10:29:09 -04:00