When doing serial file output debugging, write the config commands as
they are often useful to inspect.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Generate the data dictionary in out/klipper.dict on each build. This
makes it easier to use the dictionary when debugging.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for enhancing the precision of endstop switches by also
inspecting the phase of the stepper motor when the endstop triggers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some details on the code flow and organization have changed since
support for ARM processors was added. Update Code_Overview.md
accordingly.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rework the code so that the kinematic class (currently just
cartesian.py) has more control over the homing process.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a config option to define an amount of additional filament to feed
into the extruder during acceleration and deceleration of the
extruder. This can help ensure plastic is deposited in the correct
places during a print.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Only skip acceleration between moves if both moves perform a similar
amount of extrusion. This ensures the extruder has sufficient time to
accelerate to and from each extrude move.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow the owner of the stepper object to cacluate the maximum step
jerk velocity. This is used to ensure there is no communication error
between mcu and host.
Disable checking of jerk velocity for extruder stepper motors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Store the baud rate the MCU is configured for in the "identify" data
and use that rate when calculating the baudadjust parameter.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The test to check if the queue only needed to be moved was not correct
and it could lead to a segfault if clean_queue() was called instead of
actually increasing the queue size.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Check for an invalid count and report an error if found. This
prevents some segfaults when count goes negative.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Create a new python file (extruder.py) to control the extruder heater
and stepper motors. This separates the extruder control logic from
the cartesian robot code - making it easier to customize both the
kinematic control of the robot as well as the extruder.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
All users of max_step_velocity and max_step_accel end up multiplying
by step_dist anyway, so it's easier to store max_velocity and
max_accel.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Explicitly check for when the move_queue is empty and only call
move.calc_junction() when there is a previous move. This avoids the
need to create a dummy "sentinal" move object and it simplifies the
code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Remove the lookahead.py file and move its code directly into
toolhead.py. The MoveQueue() class is small and tightly coupled to
the toolhead code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Separate out the low-level stepper motor kinematics handling from the
ToolHead class into its own class.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Perform all acceleration calculations and lookahead checks in
millimeters using the cartesian coordinate system of the request. The
conversion to step coordinates is now done at the time of the step
timing creation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
At high step speeds, it is possible to exit the inner scan due to
integer truncation. Always update minadd or maxadd so that the outer
loop always terminates.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit da305e6b changed the objcopy command to use the --dump-section
flag. However, the 2.24 version of avr-objcopy (which is common on
raspbian installs) does not support this flag. Avoid using
--dump-section and continue to use the -j option instead.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This adds basic support for running on the Atmel SAM3x8e
micro-controllers that are found in the Arudino Due boards.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add the ARM CMSIS definitions (obtained from an Arduino copy of
libsam) in preparation for Arduino Due support.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
On faster MCUs the step and unstep events may be too close for the
stepper motor driver. Add a CONFIG_NO_UNSTEP_DELAY build option and
support the case where it is not set. This allows faster MCUs to
schedule two events for each step (one for the step and one for the
unstep).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The Arduino Due uses a 1200 baud connection to signal an erase
sequence, so avoid it during normal serial resets.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Introduce enable_tx_irq() for manipulating the AVR hardware. This
keeps the low-level hardware code together.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Default to O2 and set Os in the AVR makefile. Platforms besides AVR
are likely to produce better code with O2 so make that the default.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some architectures are faster passing regular integers than 8bit
integers. Use uint_fast8_t so that the architecture chooses the
appropriate type.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The AVR wants a uint8_t return type for irq_save(), but other
architectures will generally prefer int. Allow the board to configure
the size of the flag by introducing an irqstatus_t typedef.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Task and command handlers always run with irqs enabled, so it is not
necessary to save/restore the irq state when disabling irqs in these
handlers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some boards may not support hardware based PWM. Update the build so
that those commands do not need to be compiled if they are not
available.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some boards may not support SPI transfers. Update the build so that
those commands do not need to be compiled if they are not available.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some boards may not support the ADC hardware. Update the build so
that those commands do not need to be compiled if they are not
available.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor