This adds support for BMP280 and BME680 sensor ICs,
along with fixing calibration data readout for BME280.
Gas sensor readout for the BME680 is just the raw compensated value.
To get actual meaningful values, more research is needed.
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
The tmc2660 spec has an ambiguous "SG" field that sometimes refers to
the "stallGuard" flag and sometimes refers to the "SG_RESULT" field.
The tmc2130 and tmc5160 have similar fields that are not ambiguous, so
adopt that naming strategy.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add functionality to support a Filament Motion Sensor for detecting extruder jams as well as runouts. Works by an encoder toggling the switch_pin 0/1 as the filament is pulled through the sensor.
Signed-off-by: Joshua Wherrett <thejoshw.code@gmail.com>
Temporarily postpone loading the CAN module so that moonraker (and
similar) can improve upgrade scripts.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rework the micro-controller command protocol so that it supports
direct communication with the serialqueue.c code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The tmcuart_send command increases cpu usage on the micro-controller.
Should multiple tmcuart_send commands be issued at the same time to a
single AVR micro-controller, it could increase the load to the point
that it introduces a failure. It could also lead to tmcuart_send
transmission errors, which would cause retransmission requests, which
further increase the load.
Track and share mutexes so that only one tmcuart_send command can be
active on a single mcu at a time.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The tmc2130 (and tmc5160) will respond back with the value written
during the next SPI command. Use this feature to verify that the
value written matches the value sent.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
None of the other TMC driver enable SFILT by default and it seems
enabling SFILT may not be ideal for sensorless homing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
A working configuration example for Hiprecy Leo printer (https://www.hiprecy.com/product/402/) with no Touchscreen funcionalities because separated LCD firmware needed.
TMC2130 SPI drivers.
The Self-levelling plate sensor is PINDA probe type
Direct Drive is a BMG "3:1" gear ratio
Signed-off-by: Morgan Barresi <morganfw@gmail.com>
Machines that have no heaters produce an error when the idle timeout occurs. This commit fixes this by checking if there are any heaters to turn off.
Signed-off-by: Florian Heinze <florian@heinze.at>
Introduce a heaters.set_temperature() command and call that from
commands that set a heater temperature. This new function calls
toolhead.register_lookahead_callback() so that the idle_timeout gets
notification that activity has occurred.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Make the baud rate an optional parameter to the console.py tool. When
not present, it will default to 250000.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't try to detect a "real serial port" in serialhdl.py. Instead,
have the callers invoke either connect_uart(), connect_file(), or
connect_pipe().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add new fields to Command_Templates.md.
Remove unused self.rpm variable.
Use an explicit get_frequency() method in keeping with Klipper's
convention of not "peeking into member variables".
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This adds new config options for fans: 'tachometer_pin' to specify the
GPIO pin, and 'tachometer_ppr' (default 2) to specify the number of
signal pulses per revolution. The rpm is also exposed by get_status for
command templates and the API server. For fast fans (at least 10000
RPM), the polling interval can be shortened using the
'tachometer_poll_interval' option.
There is a new mcu object for a generic edge counter, which repeatedly
polls a GPIO pin and periodically reports the count to the host.
Signed-off-by: Adrian Keet <arkeet@gmail.com>
If `klippy` loses connection to a device, the next `read()` from the
device file descriptor will result in a zero-byte result, i.e. an `EOF`.
Right now this gives a confusing error message, so this simply handles
the special case of `EOF` and outputs a better log message.
Signed-off-by: Lasse Dalegaard <dalegaard@gmail.com>
When `serialhdl` opens a terminal device it must prevent the device from
becoming the controlling terminal of `klippy`, as such a terminal will
send additional messages to the session leader, e.g. a SIGHUP, which
would kill `klippy`. See e.g. #3981.
pySerial already does this, but for e.g. `klipper_mcu` we were not doing
this ourselves.
On Linux a process must set `O_NOCTTY` when opening any file that could
potentially be a terminal device, to avoid this.
Earlier process daemonization tools prevent this from being an issue by
double forking, but under `systemd` a process must take steps to avoid
opening a controlling terminal.
Signed-off-by: Lasse Dalegaard <dalegaard@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
With commit 53b10d3a the setup of sensorless homing could occur before
the driver was enabled which would cause the reinitialization of the
driver settings to undo the sensorless homing setup.
Use set_field() when setting the sensorless homing registers so that
it wont conflict with a driver init.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
There are two fan pins on Robin Nano 3 and the fan1 pin is PC14, not PB1.
PB1 pin that was in config example is used for the fan2 output.
Signed-off-by: Oleksii Zelivianskyi <alexeyzel@gmail.com>
we just found a small problem: Some people have slightly higher endstop positions, which caused them to have a move out of range during probe calibrate.
Signed-off-by: Christoph Frei <fryakatkop@gmail.com>
Kevin O'Connor