Allow the start value to be different from the default/shutdown value
for the pin. This will be useful for "heater fans" that should
startup in the off state, and transition to full on in a shutdown
state.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Pass the sample_ticks and sample_count parameters directly in the
end_stop_home command instead. This simplifies the code.
Also, simplify calculation of next wakeup time in
end_stop_oversample_event().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Place a small notch on one side of the square. The notch provides
interesting information on the extruder performance, and it makes it
easier to compare with previous prints of the object.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Several items were recently implemented. Remove the "cubic vs
quadratic" item as investigations into cubic compression weren't
promising.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for configuring and controlling the hardware specific to
the revision "B3" Replicape board.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Implement the conversion from print_time to the local mcu's clock
within the C code. This simplifies the python code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Extend the look-ahead mechanism to work between moves that contain Z
movement. This improves Klipper's handling of g-code produced in
"vase mode".
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It should no longer be necessary to configure "custom" commands during
mcu setup. The ad5206 and static_digital_output config sections
should provide similar functionality.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Compile the PRU binary with -Os optimization, but request that the
timer dispatch code be compiled with -O2 optimization. This improves
the performance of timers slightly.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The gcc -Os option significantly reduces the size of the PRU binary
and it has little impact on performance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It is not necessary to limit stepper acceleration - only the limiting
of stepper torque is important.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a CONFIG_SIMULAVR option to the Kbuild menus and don't directly
prompt users for CONFIG_WATCHDOG or CONFIG_SERIAL_BAUD_U2X. The only
reason to disable these options would be if one were running on
simulavr. This simplifies the user visible menu options.
Also, only show CONFIG_CLEAR_PRESCALER for at90usb1286 chips.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Instead of assuming the maximum PWM value is 255, export a constant
from the firmware to the host with the maximum value.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Those that reach Klipper via github may jump directly to the docs/
directory in search of documentation. Add README.md and rework
Overview.md with that in mind.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The term "firmware" is ambiguous - it could refer to the entire
project (host and micro-controller software) or to just the
micro-controller software. Avoid the term in the documentation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The Klipper software has progressed to the point where it does not
need to be described as "experimental" software.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Detect avr gcc v4.8.1 and then disable warnings during the klipper.o
linking to suppress bogus "misspelled signal handler" warnings.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a system startup script so that Klipper can automatically start at
boot time. Create an installation script that will install the system
dependencies and the startup script.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor