Adjust the HEND default, which was faulty after the the fields update, remove disallowance of setting CS
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
Adds parameter for bed meshes to be adjusted relative to a probed point
during calibration. This allows the probe z offset to be ignored for
probes that are not stable over time (for example, the thermal drift of
inductive probes). An endstop other than the probe is then necessary to
determine the bed-nozzle offset.
Signed-off-by: Matt Baker <baker.matt.j@gmail.com>
menu: Show current positions based on gcode positions
Added "move_[xyze]pos" properties to the "gcode" object for use in menus.
The new properties track the toolhead's position in gcode coordinates,
taking gcode and bed leveling offsets into account.
This position is equal to the value returned by M114 gcode.
Changes the move menus to show current position based on gcode
position. This allows gcode offsets and bed leveling offsets
to be taken into account, and prevents unexpected toolhead
movements when moving it using the menu.
Signed-off-by: Robert Konklewski <nythil@gmail.com>
The z_adjust offset provided to adjust_steppers is calculated given the
steppers adjust exactly according to the given x_adjust/y_adjust. As the
algorithm eliminates an offset that is common to all steppers, this offset
must be taken into account in the final correction.
Signed-off-by: Arne Jansen <arne@die-jansens.de>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The z_offset calculation should have been calculated from the probe
height to the measured bed position.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the field names from the trinamic specification. This makes the
field similar to all the other driver_XXX config options.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
sense_resistor is now a mandatory parameter for tmc2660 blocks. Duet2 users should use a value of 0.051
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
Don't immediately raise an error if the heating_gain check fails.
Instead, just transition to the normal max_error check. This should
make the code less likely to raise an error should the heater have a
slow approach to the target temperature.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow the first check_gain_time interval to only require a
heating_gain relative to the lowest observed temperature during that
interval. This makes the code less likely to raise a spurious error
when the heater is enabled while the heater temperature is dropping.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't reset the error counter if the reported temperature is
significantly above the target temperature. This may help catch cases
where the temperature sensor reports random values.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This implementation includes a BaseSensor class that all underlying sensor implementations should subclass.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Support reading a "gcode_id" parameter from heater/sensor config
sections.
Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Instead of directly turning off motors, heaters, and fans from
gcode.py, raise a new event and allow the heater, fan, and toolhead to
handle the event as needed.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The 'bed_shape' option has been removed. The user will enter a 'bed_radius' if they have a round be, otherwise they should enter 'min_point' and 'max_point'. When the bed is round the user should supply a 'round_probe_count' option, otherwise just 'probe_count'.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Use the field helper to simplify the bit manipulation in the driver.
This also enables the extended DUMP_TMC output.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Raise a printer.config_error() on an invalid register_command() call.
This error is easier to handle for the vast majority of callers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Implementation of "PROBE_ACCURACY" to measure the maximum, minimum,
average and standard deviation of a probe.
Signed-off-by: Rui Caridade <rui.mcbc@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support added for filament diameter sensor. Sample configuration parameters added to example-extras.cfg.
Signed-off-by: Mustafa YILDIZ <mydiz@hotmail.com>
Adds the ability to register a custom/generic heater through a new extra called heater_generic.
This takes a gcode_id that is reported by M105. Adds a new command to set the temperature for any heater using the syntax:
SET_HEATER_TEMPERATURE HEATER=<heater_name> TARGET=<target_temp>
Signed-off-by: John Jardine <john@gprime.net>
- When using absolute extrusion the gcode position e-axis position is now captured on PAUSE and restored in RESUME with a call to the G92 handler.
- Add a get_status() function that returns a dictionary with an 'is_paused' key.
- Do not allow consective calls to PAUSE or RESUME to exectue. Also do not allow a RESUME to executed without a previous PAUSE.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
In the normal case, a regular pin_up command should be sufficient to
raise the probe. (Should the regular pin_up fail, the code can issue
a "reset" command during the retry.)
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit c3efcd9c moved the config_spi setup to a build_config callback.
It's also necessary to move the config_thermocouple to a build_config
callback as well.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add helper function for reading current, microsteps, and stealthchop
settings from the config file. Use these helpers in both the tmc2130
and tmc2208 modules.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move these helper functions to the FieldHelper class so that they can
be used by other Trinamic drivers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Report values of TMC2208 register fields in DUMP_TMC command to help in
tuning and diagnostics.
This also adds functions to refer to register fields by name for TMC drivers
and register mappings for TMC2208.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Signed-off-by: Dmitry Frolov <dmitry.frolov@gmail.com>
Stopping the connect sequence can make it difficult to get the bltouch
out of an error state. Allow the connect to proceed, ideally if the
bltouch stays in an error state it will be detected during the first
probe attempt.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
I noticed Octoprint was disconnecting after a while, and after reading the logs, I came across this error:
```
Unhandled exception during run
Traceback (most recent call last):
File "/home/pi/klipper/klippy/klippy.py", line 171, in run
self.reactor.run()
File "/home/pi/klipper/klippy/reactor.py", line 176, in run
g_next.switch()
File "/home/pi/klipper/klippy/reactor.py", line 203, in _dispatch_loop
timeout = self._check_timers(eventtime)
File "/home/pi/klipper/klippy/reactor.py", line 82, in _check_timers
t.waketime = t.callback(eventtime)
File "/home/pi/klipper/klippy/extras/idle_timeout.py", line 62, in timeout_handler
return self.check_idle_timeout(eventtime)
File "/home/pi/klipper/klippy/extras/idle_timeout.py", line 59, in check_idle_timeout
return self.transition_idle_state(eventtime)
File "/home/pi/klipper/klippy/extras/idle_timeout.py", line 35, in transition_idle_state
logging.exception("idle timeout gcode execution")
NameError: global name 'logging' is not defined
```
I therefore added the missing import.
Signed-off-by: Samori Gorse <samori.gorse+github@gmail.com>
This module adds PAUSE and RESUME gcodes that can programatically determine if the gcode is printing from virtual sd or over the serial connection. It also captures the current toolhead position and gcode feedrate on pause, and recovers that position and feedrate on resume.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
- Add is_active() member function to return the active printing status of the virtual sdcard
- M27 now reports current file position when file has been opened. See http://marlinfw.org/docs/gcode/M027.html
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Add support for performing linear interpolation between a set of
measured temperature/resistance pairs.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the low-level PrinterADCtoTemperature() class from thermistor.py
to adc_temperature.py and use it from the Linear() class.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor