Add a command that will turn off all heaters in the printer. Run this
command in the default idle_timeout action.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update the document to recommend tuning with decreased acceleration
and with square_corner_velocity disabled. Using this approach makes it
possible to test with significantly higher pressure advance values.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This can be flashed to e.g. the duet wifi using bossac. It requires a
later version as is currently included in the klipper repo (1.8
vs. 1.2). Comms are currently via UART0 only, USB serial is still TBD
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
The Todo.md file has gotten stale, and it is no longer an effective
mechanism for tracking changes. Remove it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add initial support for commands that will forcibly move a stepper
(without updating the kinematic classes with the new position).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The junction_deviation configuration parameter has a number of quirks
that make it difficult to configure. Replace it with a
"square_corner_velocity" configuration parameter.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add M117 and M73 to the list of supported G-Codes.
Also, remove M117 from the list of commands reported by the HELP
command as that command is typically only used to list "extended
g-code" commands.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add basic SPI support and associated documentation.
v2: remove baud rate check, fix baud rate calculations
v3: finish transaction with BSY check, disable SPI when not in use
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
The PRU code size has grown too close to the maximum - remove the ADC
code to reduce its overall size. (On the beaglebone, the Linux
process can, and typically does, do the ADC reading.)
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for an itersolve_set_position() function that sets a
stepper position from a cartesian coordinate. This eliminates the
need for both the python and C code to be able to translate from a
cartesian coordinate to a stepper position.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Calculating the cartesian position from the stepper positions can be
complex and cpu intensive, so rename it to calc_position() to be more
descriptive.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
When using multiple micro-controllers it may be necessary to use an id
from /dev/serial/by-path/ instead of /dev/serial/by-id/. Also,
emphasize that in config/example-multi-mcu.cfg.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change the get_status command to get_clock. Don't report the shutdown
status in the new get_clock command.
The primary purpose of this change is to force the host code to report
a firmware version mismatch with older firmwares as recent changes
(namely the ordering of message block acks) have subtle
incompatibilities if different host/mcu code is used.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the new gcode.register_mux_command() so that SET_PRESSURE_ADVANCE
works correctly with multiple extruders.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Improve the SPI message transmit system. Add support for bus speed
and bus mode. Add support for sending SPI messages on shutdown.
Signed-off-by: Petri Honkala <cruwaller@gmail.com>
Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the C code out of the main klippy/ directory and into its own
directory. This reduces the clutter in the main klippy directory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The M206 command is confusing (it uses negative offsets) and isn't
very flexible. Add a new SET_GCODE_OFFSET command to make it easier
to add virtual offsets to gcode commands.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Drop support for M303 and PID_TUNE, and replace it with a new
PID_CALIBRATE command. Move the logic for this command from heater.py
to a new pid_calibrate.py file in the extras/ directory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It looks like OctoPrint is expecting the result from M114 to be
relative to the last G92 command. Also, introduce GET_POSITION to
report the actual location that the printer is at.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Emphasize that the log file needs to be attached to the issue.
Encourage M112 to be issued on every bug report.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's common for multiple steppers to use the same stepper enable
line. Detect this and only create a single digital_out oid on the
micro-controller.
Also, prohibit any other pin from being used multiple times in the
config file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update the pressure advance tuning document to note that 0.20 is
likely the ceiling of a useful pressure advance setting.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Provide a document with basic steps that a user can run to verify that
the pins in the configuration file are set correctly.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add an initial document detailing best practices for contributing to
the document. Add the "developer certificate of origin" document.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Try to make the Installation document more friendly to users not
familiar with the Linux command-line. Offer some hints on how to
obtain ssh and how to edit the config file remotely.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add additional notches and move them to the inside of the square where
they will not impact the outside perimeter test.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor