dcedd84fe1
config: Lulzbot TAZ6 w/ Dual v3 Toolhead Config ( #2111 )
...
Signed-off-by: Ryan Densberger <magshooterz@gmail.com>
2019-10-30 12:37:22 -04:00
e2f5e2871c
docs: Recommend OctoPrint v1.3.12 in Installation.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-30 11:02:03 -04:00
d65f2e2861
docs: Minor cleanup to square_tower.scad
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-27 12:16:17 -04:00
43453131ac
config: Only document thermistors in example.cfg
...
Move the common temperature amplifier config descriptions to
example-extras.cfg.
Also, minor changes to wording of some example-extra.cfg sections.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-27 12:03:59 -04:00
1a69f38e6e
flash_usb: Pass -t $CONFIG_MCU to flash_usb on all targets
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-26 18:48:00 -04:00
538d6ac3a2
flash_usb: Use "-s" option to specify flash offset on atsamd
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-26 18:33:00 -04:00
c694da3753
flash_usb: Change dfu-util to reset the board after a flash on stm32f4
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-26 18:06:32 -04:00
4b4e309e1b
flash_usb: Inform user to manually reset after stm32f4 flash
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-26 17:46:18 -04:00
5131ec5eb0
stm32: Add support for flashing over usb on stm32f042
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-26 17:11:04 -04:00
2ecc8d8f62
stm32: stm32f4 usb boot check only needed when CONFIG_USBSERIAL
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-26 16:56:33 -04:00
5da6a62759
stm32f4: Add support for flashing over USB
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-26 13:24:59 -04:00
0ba5819370
tmc_uart: Don't try to configure analog pins to -1 value
...
Commit 6f5f2a3b
2019-10-26 11:33:30 -04:00
081c24326d
atsam: sysio support is only available on sam4s
...
Fix sam4e build error introduced in commit f723a314
2019-10-24 22:21:47 -04:00
f723a3141e
atsam: Allow PB4-PB7,PB10-PB12 to be used as gpio on sam4
...
A separate "sysio" register must be set in order to use some port B
pins on the sam4 mcu.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-24 22:02:29 -04:00
6f5f2a3bc7
tmc_uart: Make sure to set analog mux pins after a restart
...
Don't assume the analog mux pins are in a low state at startup.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-24 22:00:58 -04:00
d6d2be66e4
config: The duet2 maestro uses a 2200 ohm pullup resistor
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-24 13:07:07 -04:00
9a11286327
stm32: Implement armcm_main() in arch specific code
...
Move armcm_main() to stm32f0.c, stm32f1.c, and stm32f4.c. This gives
the arch specific code more control on the early boot setup.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-24 11:35:18 -04:00
faeaa54925
armcm_boot: Use armcm_main() instead of main() to start board code
...
The main() function has a special meaning to gcc and using it can
result in different code generation. Use armcm_main() to avoid that.
Also, invoke SystemInit() from the board specific armcm_main() code.
This gives the board code more control over board initialization.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-24 11:16:10 -04:00
632ff9e55a
docs: Update benchmarks for stm32f0
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-23 21:45:07 -04:00
0b0c47c566
stm32: Support PA11/PA12 pin remap on stm32f042 tsop20 chip
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-23 21:34:48 -04:00
a6d90bb95e
stm32: Support stm32f042 build from stm32/ directory
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-23 21:34:48 -04:00
2c535106ee
stm32: Initial support for stm32f070
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-23 21:19:03 -04:00
7e090a996a
lib: Add a copy of stm32f0 cmsis files from v1.10.0
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-23 21:16:35 -04:00
7b792e40d5
stm32f0: Rename internal build symbol from MACH_STM32F0 to MACH_STM32F0_HAL
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-23 21:16:35 -04:00
a46244057c
stm32: Support 16bit packet memory access on usbfs controller
...
The stm32f0 line uses 16bit packet memory reads/writes (as opposed to
the goofy 32bit accesses required on the stm32f103).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-23 21:16:35 -04:00
c2881f7d15
stm32: Be explicit in layout of gpio banks in digital_regs variable
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-23 21:16:35 -04:00
f160a3a824
docs: Reword Pressure_Advance.md paragraph on kinematic impact
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-23 19:50:51 -04:00
ccbdb6c531
docs: Pressure_Advance.md should recommend setting ADVANCE_LOOKAHEAD_TIME
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-23 19:34:59 -04:00
c794e11c67
docs: Update Pressure_Advance.md to use tuning tower
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-23 19:28:03 -04:00
b8a6160646
docs: Update example openocd config in Bootloaders.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-23 19:05:04 -04:00
f07292084b
docs: Remove outdated stm32f1.md document
...
The stm32f103 has become popular in the "skr mini" series of boards.
As a result, the stm32f1.md document is no longer relevant.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-23 18:53:11 -04:00
e0afc74cc7
config: Fix EXP1 comment in generic-bigtreetech-skr-e3-dip.cfg
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-23 16:07:08 -04:00
b91993d6a4
config: Add generic-bigtreetech-skr-e3-dip.cfg config
...
Reported by @salimvanak.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-23 15:59:26 -04:00
40d076cce5
stm32: Use stm32f103xe header for stm32f103 line
...
Use the "e" revision so that the SPI3 device is available for use.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-23 15:49:00 -04:00
ef142af785
config: Rename config to generic-bigtreetech-skr-mini-e3-v1.0.cfg
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-23 15:04:15 -04:00
48530db50e
test: Add generic-bigtreetech-skr-mini-e3-v1.2.cfg to config tests
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-23 15:01:34 -04:00
c7fe338bfb
config: Skr mini e3 v1.2 template ( #2069 )
...
Signed-off-by: Eelco Pandelaar <epandi@gmail.com>
2019-10-23 14:57:00 -04:00
9cd6273d52
scripts: Use current username in install-ubuntu-18.04.sh
...
Set KLIPPER_USER to $USER instead of "octoprint".
Signed-off-by: Nathan Chiu <nhchiu2009@gmail.com>
2019-10-23 14:54:31 -04:00
dd12c981ef
temperature_fan: add get_status() function
...
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-10-22 22:10:13 -04:00
d85b395a9c
bed_mesh: fix error reporting
...
Fix invalid string formatting in the parse_pair() helper.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-10-22 22:09:33 -04:00
abdfd92e99
docs: Update release notes for v0.8.0 release
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-21 22:30:04 -04:00
dd9259aaf3
docs: Minor wording changes to Manual_level.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-16 16:48:50 -04:00
4811b58b39
docs: Update Manual_Level.md with recent config changes
...
The sample count and associated settings are no longer in the
screws_tilt_adjust config section - they are now in the probe config
section. Remove them from the guide.
Reported by @theopensourcerer.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-16 16:35:32 -04:00
dd77b46de9
docs: Note AD849x support in Features.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-15 13:08:43 -04:00
1e8582e3f6
stm32: Make sure to turn on the usb clock before writing to the packet memory
...
The USB clock needs to be enabled prior to writing to the USB packet
memory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-13 14:33:23 -04:00
789659599c
adc_temperature: add support for AD849x thermocouple amplifiers ( #1994 )
...
Signed-off-by: Geoff Shannon <geoffpshannon@gmail.com>
2019-10-10 20:11:34 -04:00
6d7d079bab
tuning_tower: Only cancel tuning tower test if extrude at notably lower z
...
Some print start scripts may extrude at a position slightly higher
than the first z layer height. Tweak the backwards z test to reduce
the chance of the tuning test ending prematurely.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-04 20:10:12 -04:00
4ef0db5087
docs: Update Config_Change.md with safe_z_homing change
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-10-03 18:09:01 -04:00
2b553a8108
safe_z_home: Fix unintended change in default behavior
...
PR #1970 introduced a new parameter, controlling the default behavior of the safe_z_home-module. To avoid unexpected changes, the default of the move_to_previous is now defaulted to False.
Signed-off-by: Nils Friedchen <Nils.Friedchen@googlemail.com>
2019-10-03 18:06:08 -04:00
7605244fa0
safe_z_home: Fix issue where 'home_xy_position: 0,0' did not position at 0,0
...
If '[stepper_x]' and/or '[stepper_y]' have a 'position_min' that is
non-zero, and '[safe_z_home] home_xy_position' is '0,0'; then the 'G28'
command will _not_ move to '0,0'; but stay at 'position_min' during the
Z endstop test.
This fix corrects this issue.
Signed-off-by: Jason S. McMullan <jason.mcmullan@gmail.com>
2019-10-03 18:05:21 -04:00
radensb