Explicitly disable the SysTick interrupt and explicitly set the stack
pointer, as some bootloaders aren't handling this correctly.
Signed-off-by: Chris Lombardi <clearchris@hotmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change the "product id" from the redundant "Klipper firmware" to the
CONFIG_MCU value. For now, only make this change on boards that have
CONFIG_HAVE_CHIPID set.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The main() function has a special meaning to gcc and using it can
result in different code generation. Use armcm_main() to avoid that.
Also, invoke SystemInit() from the board specific armcm_main() code.
This gives the board code more control over board initialization.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename the linker script so the build does not have any conflicts with
the armcm_boot.d dependency file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add basic ARM Cortex-M C init code and build linker scripts to
src/generic/ code. This can be used to simplify the various ARM board
code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Make it clear that the name of the constant being defined is a string.
When the value being defined is also a string, use a new
DECL_CONSTANT_STR() macro.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The ARM CortexM3 (and later) chips almost always have a 32bit timer in
the "Debug and Watch Trace" (DWT) unit which resides within the cpu
core itself. This timer is generally faster to access than timers
located on the chip's peripheral bus. When combined with the standard
ARM SysTick timer it provides a (generally) portable mechanism to
implement Klipper's software timer mechanism. It's generally also
faster than using the vendor specific timers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Increase the amount of time to "busy wait" in the timer dispatch loop
to 2 micro-seconds. This, in practice, causes stepper step and unstep
events to occur within a single hardware interrupt. Doing that helps
stabilize the single active stepper performance benchmarks.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Call usb_read_bulk_out() before calling command_find_and_dispatch() as
this optimizes the common case where each usb packet contains a single
new message block.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Fix travis-ci build failure by forcing the data field of the struct
usb_string_descriptor to be the same type as a 16bit unicode string.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use new usb_read_ep0_setup() function when reading a setup packet -
this allows the low-level usb hardware code to better handle errors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
A zero length packet should only be sent at the end of a transmission
if the host is expecting more data.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Maintain the state tracking code entirely within a usb_do_xfer()
method. This simplifies the callers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use "ep0" when referring to endpoint0 - don't use "setup" as that can
be confused with the low-level usb setup token.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's common for boards to have restrictions on the type of each
endpoint. So, make it possible for the board to select the endpoint
ids for each endpoint.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change the simulator to use the generic timer_irq.c and serial_irq.c
code for (dummy) timer and io handling. This is just to make the code
a better example for other developers (most micro-controllers will use
the timer_irq.c and serial_irq.c code).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The SPI interface needs to be enabled and configured to the correct
settings of a given oid before CS is asserted. The new function
spi_prepare() allows ports to do that.
This port only introduces the new function in all ports with no
implementation and adds the call to the Klipper generic firmware code.
That means everything still works as before. Ports need to be changed
to fix the underlying issue.
Discussion about the motivation here:
https://github.com/KevinOConnor/klipper/pull/453#issuecomment-403131149
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
If the mcu is using a traditional serial port, then only send a new
message block if there is space available in the mcu receive buffer.
This should make it significantly less likely that high load on the
mcu will result in retransmits.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Send the ack after processing commands - this gives the host code more
information on serial buffer utilization.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Prefer using 'uint8_t' buffers as it is too easy to run into C sign
extension problems with 'char' buffers. Prefer using 'uint_fast8_t'
for buffer lengths as gcc does a better job compiling them on 32bit
mcus.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The gpio_out_toggle() function in the sam3x8e and stm32f1 code was
only valid if it was called with irqs disabled.
Commits 018c5daa and 9c52ad43 enabled the lcd code which called
gpio_out_toggle() with irqs enabled. This could cause corruption of
the gpio state.
Introduce a gpio_out_toggle_noirq() function that will only be invoked
with irqs disabled, and fix gpio_out_toggle() on sam3x8e and stm32f1
so that it safe to call even if irqs are enabled.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Improve the SPI message transmit system. Add support for bus speed
and bus mode. Add support for sending SPI messages on shutdown.
Signed-off-by: Petri Honkala <cruwaller@gmail.com>
Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Extract out common code from avr/serial.c, sam3x8e/serial.c, and
stm32f1/serial.c into a new generic/serial_irq.c file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for reading analog values via the standard Linux IIO
interface. This can be used on Replicape boards to sample analog
input pins.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor