Update the lookahead code to track both normal toolhead acceleration
as well as a pseudo acceleration to the point of deceleration. This
reduces the top speed of small zig-zag moves and it reduces printer
vibration during these moves.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It is not necessary to track the do_calc_junction flag as it can just
as easily be determined at the top of the calc_junction() method.
This simplifies the code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
When calculating the extruder lookahead, determine how far to
lookahead by the amount of elapsed time each move takes. This makes
the extruder lookahead code more flexible as it is no longer limited
to the next immediate cornering moves.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Instead of calculating min/max_corner_v in the toolhead class,
calculate it in the extruder class. This keeps the extruder specific
code together.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
When testing via a gcode input file, it's easier to debug problems if
the program exits upon the first exception.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Make sure max_corner_v2 is fully calculated before proactively
flushing moves from the lookahead queue. Without this, some moves
would do unnecessary pressure advance during cornering.
Also, handle the min/max_corner_v2 calculations correctly in the rare
case where a move that does only acceleration is immediately followed
by a move that does only deceleration.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The junction speeds are tracked in velocity squared - introduce the
common suffix "_v2" to track that instead of using a prefix of
"junction_".
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
There is a small possibility that a shutdown could occur between
clearing transmit_max and clearing transmit_pos - so make sure to
handle the case where transmit_pos > transmit_max.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
As long as the code is careful when writing the in_sendf variable it
should be safe to update it without having to disable irqs.
Also, make sure in_sendf is cleared on shutdown.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow sendf() to be called from irq and timer context - check for the
case where sendf() is called while already in sendf() and simply
discard those messages. This makes it safe to use output() debugging
calls even in irq and timer context.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Continue to resend the pwm value even if the last value was zero -
this extends the debugging info.
Also, add the target temperature to the pwm debugging.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Fix a bug causing timers to be delayed when pause() is called from a
fd event. The eventtime needs to be reloaded when an old greenlet is
reactivated.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Check for msgproto.error and warn the user about version firmware
version mismatch. Raise msgproto.error when extracting firmware
constants.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use a base of 256 instead of 65536 when calculating the sum of the
square of the clock differences in the stats. This makes the
calculation more accurate. Export the new base via DECL_CONSTANT for
the host to access. Use DIV_ROUND_UP() when adjusting for the base to
ensure no lost ticks. Do the division after multiplication in the
common case where the time between stats_task() invocations is less
than 64K ticks.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Instead of requiring the user enter velocity and accel parameters for
extrude only moves, calculate sane defaults from the printer's maximum
velocity and accel.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Be more clear on which parameters have defaults and which parameters
must be specified in the config.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's possible for a printer with very fine resolution to require a
large number of steps for a homing operation. Instead of storing all
of those steps in memory, periodically flush the queue should more
than 64K steps be present. This keeps a reasonable limit on the
amount of ram needed to store steps.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The serialqueue_flush_ready() code was used to flush queue_step
commands during a homing operation. It's no longer necessary now that
moves during a homing operation use the normal message priority
system.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The endstop homing system requires all queue_step commands be in the
MCU's 'move queue' before endstop checking starts. Use the normal
message priority system to request that stepper queue_step commands
are received prior to the start of the end_stop_home command. This
simplifies the code and removes the need for special serial queue
flushing.
This also fixes a bug in homing operations that take longer than 2^31
clock ticks.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a is_kinematic_move flag to the Move class and clear it on extrude
only moves. Don't call the kinematic check_move() or move() methods
for extrude only moves.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change the default compression error window (max_error) from 50us to
25us - it's common for stepper motor drivers to have 30us for their
"pwm fixed off time" and it would be good for the steps to be
scheduled within that time.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Revert 4a16053c and avoid integer overflows in the addfactor
calculation by exiting the loop early if count > 0x200. This provides
stronger protection against overflows.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Log the constants reported by the MCU and log the number of move items
allocated after configuration.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit a217c0f3 changed the way the "addfactor" was calculated.
Unfortunately, it was possible for the updated method to cause an
integer overflow and have a negative addfactor. Fix this by
explicitly casting the addfactor calculation to uint32_t.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some motors have very small step distances and they can generate over
a million steps during a homing operation. Increase the maximum count
to ten million to avoid triggering the internal sanity check.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor