Update the graphstats.py graphing script so that it works with recent
stats changes - the stats can now contain groups that end with a ':'
and the print_time is no longer reset to zero on a new print.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The Beaglebone hardware prevents the PRU from updating the pinmux
board settings. As a result, the PRU can't directly change the pin
direction or change the pullup resistor settings. Warn the Beaglebone
users of this limitation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Make sure the ADC module gets loaded during startup - it's normally
loaded by the cape manager eeprom, but there's no harm in requesting
it explicitly.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Only open the watchdog device after the console has been opened. The
machine should not reboot in the unlikely event the console can't be
opened.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If an MCU signals a shutdown from the background thread, notify the
main thread and handle the shutdown there. Dispatch shutdown handling
from the main Printer() class instead of from the Toolhead class.
This simplifies the shutdown logic.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow the start value to be different from the default/shutdown value
for the pin. This will be useful for "heater fans" that should
startup in the off state, and transition to full on in a shutdown
state.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Continue to sample the ADC input pins even if the MCU goes into a
shutdown state. This enables the printer to continue reporting
temperatures even on an mcu error.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Pass the sample_ticks and sample_count parameters directly in the
end_stop_home command instead. This simplifies the code.
Also, simplify calculation of next wakeup time in
end_stop_oversample_event().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It is possible to have an acceleration greater than max_z_accel on
XY+Z moves. That needs to be taken into account when calculating the
min_stop_interval. This prevents spurious "No next step" MCU errors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It appears some versions of Debian will load the PRU with firmware on
boot, so make sure to always deactivate the PRU before attempting to
activate it with new firmware.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Place a small notch on one side of the square. The notch provides
interesting information on the extruder performance, and it makes it
easier to compare with previous prints of the object.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the stepper phases are known then it is possible to arrange for the
0.0 position to occur at a full step. On cartesian style printer,
this makes it possible for the Z levels to occur at full steps (which
may help reduce "Z ribbing").
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't discard samples that are less than 500us from the prediction
regardless of the prediction variance. Also, don't use the prediction
variance in the external time estimate.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Several items were recently implemented. Remove the "cubic vs
quadratic" item as investigations into cubic compression weren't
promising.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some printers can show occasional noise on the endstop pin. Support
sampling the endstop pin multiple times to attempt to filter out this
noise.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Implement a "moving" linear regression between the reported mcu clock
and the sent_time of the get_status message that generated that
report. Use this linear regression to make predictions on the
relationship between the system time and the mcu clock.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
On a retransmit, the sent_time of the command associated with the
given response message isn't accurate.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Revert commit f37fc775. It is not valid to pass a conservative
frequency to serialqueue.set_clock_est() as that function may not be
called for extended periods - a too low frequency would eventually
lead to "Timer too close" mcu errors.
Instead, increase the 1ms time offset to 5ms to avoid corner cases
that could lead to a message arriving too soon.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This prevents divide by zero errors during stats output if the stats
are generated before a connection completes.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor