Purely esthetic. Make all tmc driver init code similar to one another. The various fields were grouped based on the register which they affect or the function they perform.
Signed-off-by: Alex Voinea <voinea.dragos.alexandru@gmail.com>
Previously, the globalscaler was calculated during the config parsing and set to a fixed value. If the current was changed for any reason after the initialization, only IRUN and IHOLD would be changed. This however caused issues:
- If the new current was lower, then the resolution of the possible current values would be low since there are only 32 IRUN/IHOLD steps.
- If the new current was higher, it wouldn't actually work since IRUN and IHOLD are capped at 31, so it wouldn't be possible to increase the current without increasing globalscaler.
With this commit, the globalscaler is recalculated whenever necessary in order to ensure the correct range of IRUN/IHOLD is used.
Signed-off-by: Alex Voinea <voinea.dragos.alexandru@gmail.com>
Make all the microstep lookup table registers configurable via the
config file. It also loads the default values.
TMC220x and TMC2660 do not support this feature.
Signed-off-by: Alex Voinea <voinea.dragos.alexandru@gmail.com>
The code automatically reduces the hold_current so that it is no
greater than the run_current. However, this could lead to confusing
behavior if one reduced and then increased the run_current via
SET_TMC_CURRENT commands. To avoid that, this change adds support for
tracking the requested hold_current - thus changes to run_current
don't subtly alter the hold_current.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The Trinamic specs aren't consistent with upper vs lower case, which
can be confusing. Improve clarity by using lower case names
consistently in the code. Register names will continue to use all
upper case naming in the code.
Update the SET_TMC_FIELD command to automatically convert field names
to lower case.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
With commit 53b10d3a the setup of sensorless homing could occur before
the driver was enabled which would cause the reinitialization of the
driver settings to undo the sensorless homing setup.
Use set_field() when setting the sensorless homing registers so that
it wont conflict with a driver init.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The tmc5160 field formatters were mostly duplicates of the tmc2130 -
add the "reset" field to tmc2130.py so both drivers have similar
reporting.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Refactor the tmc driver implementations so that there is a single
implementation of the SET_TMC_CURRENT command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for enabling the stepper via the communication channel.
This improves support for boards with a shared enable line.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Only the tmc2208 driver needs special read register translation logic.
Rework the code so a default implementation is available for all the
other drivers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
List all the configurable parameters in the tmc5160 example block and
use similar wording as the other tmc drivers.
Also, don't allow DEDGE to be configured as it would just break the
current code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Introduce TMCMicrostepHelper and TMCStealthchopHelper helper code that
uses the mcu_tmc interface. Update the callers to use these new
helpers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Perform the register initialization directly from TMCCommandHelper and
perform it during the "connect" phase. This unifies the register
setup for the TMC2130, TMC2208, TMC2660, and TMC5160.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Alex Voinea