The stm32f103 has become popular in the "skr mini" series of boards.
As a result, the stm32f1.md document is no longer relevant.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The sample count and associated settings are no longer in the
screws_tilt_adjust config section - they are now in the probe config
section. Remove them from the guide.
Reported by @theopensourcerer.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some print start scripts may extrude at a position slightly higher
than the first z layer height. Tweak the backwards z test to reduce
the chance of the tuning test ending prematurely.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
PR #1970 introduced a new parameter, controlling the default behavior of the safe_z_home-module. To avoid unexpected changes, the default of the move_to_previous is now defaulted to False.
Signed-off-by: Nils Friedchen <Nils.Friedchen@googlemail.com>
If '[stepper_x]' and/or '[stepper_y]' have a 'position_min' that is
non-zero, and '[safe_z_home] home_xy_position' is '0,0'; then the 'G28'
command will _not_ move to '0,0'; but stay at 'position_min' during the
Z endstop test.
This fix corrects this issue.
Signed-off-by: Jason S. McMullan <jason.mcmullan@gmail.com>
Below off_below the fan will be turned off. When configured correctly this
can prevent stalling, which may lead to overheating and failed fans. To
simplify calibration and use of this setting, off_below is applied in the
input duty cycle domain, prior to any scaling due to e.g. max_power.
Signed-off-by: Nicholas Seckar <nseckar@gmail.com>
When enabling "low level options" in Kconfig, selecting a chip that is
20Mhz capable would result in 20Mhz being the default. A 16Mhz speed
is the preferred default, so list that first in the menu.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The FIOSET and FIOCLR registers may not set an initial value if the
pin is not in an output mode. So, use FIOPIN to set the initial
value.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
When reducing the maximum speed due to the max_accel_to_decel setting,
move velocity limits must still be propagated. Otherwise, the
trapezoid move planner may produce moves with velocity jumps.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Since the previous config file was laid out only for TMC2208 drivers and was missing most other pins, I made a comprehensive configuration file, with hardware names for all available functionality.
Signed-off-by: Tobias Weiß <t.weiss@bk.ru>
Once a hop is performed, it will only be re-issued if the z-axis has been
moved in the meantime. Usually it is only moved by a z-homing so doing so
will cause safe_z_home to do the hop on the next homing action.
When z-axis is homed, x and y positions are known. When setting this
boolean option, these are set back to their last positions.
Whenever a hop is specified it is re-issued after the Z axis has been
homed. This is especially necessary when a pressure-based probe is used.
Also, the module decides if a hop is necessary, based on either a known
Z position or a flag that is set whenever the motors are disabled.
Signed-off-by: Nils Friedchen <Nils.Friedchen@googlemail.com>
Previously, when a sercom pin specified the mcu (myname:PIN), it would result in a pin enumeration error.
Signed-off-by: John Jardine <john@gprime.net>
Kevin O'Connor