Move the definition of SERIAL_BAUD to the main src/Kconfig file. Only
show this as an option if the user selects the ability to configure
low-level options.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The sam3 i2c code and the linux code use a 7-bit i2c address, while
the avr, lpc176x, and samd21 i2c code uses an 8-bit address with the
least significant bit always zero. A similar issue occurred in the
host code (sx1509.py and replicape.py use 7-bit addresses while
uc1701.py and mcp4451.py use 8-bit addresses).
Consistently use 7-bit addresses in all the code. This breaks
compatibility between host and mcu software, so make a change to the
config_i2c command to force users to synchronize software updates.
This also breaks common Smoothieboard configs, so update the mcp4451
code to validate the i2c_address.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add note that `under power` may be related to communication issues.
Signed-off-by: Wilfried Goesgens <dothebart@citadel.org>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add documentation on howto configure the BL-Touch device with
Klipper. A second paragraph addresses possible issues with BL-Touches
Signed-off-by: Wilfried Goesgens <dothebart@citadel.org>
I have made one change to `gcode.py` to support quoted parameter
values.
I have added support for the basic `M118` command (see
https://reprap.org/wiki/G-code#M118:_Echo_message_on_host). I have
also added a `RESPOND` command that takes extended parameters.
`ECHO` might be a better name than `RESPOND` but is already defined
in `gcode.py`.
Signed-off-by: Alec B. Plumb <alec@etherwalker.com>
Cheap mechanical servos have small flickering. When this servo stay on one position, this flickering slowly destroy internal potentiometer and make servo unusable. Many mechanisms need servo only to change position. Therefore I create this minor path to enable/disable servo. It stop pulses for this servo, that's all.
Corresponding G-code is:
SET_SERVO SERVO=config_name [WIDTH=] [ENABLE=<0|1>]
SET_SERVO SERVO=config_name [ANGLE=] [ENABLE=<0|1>]
For example:
SET_SERVO SERVO=touch ANGLE=80 ENABLE=1 ; enable servo and set position
G4 P200 ; wait 200ms
SET_SERVO SERVO=touch ENABLE=0 ; disable servo
This patch add one option to servo configuration:
enable: <False/True> # default True
It not have impact to user code existing already because it is optional parameter and default value is same as original behavior.
Signed-off-by: Jiri Dobry <jdobry@centrum.cz>
The gitdir previously could be absent and produce a version of "" in
spite of checks for it. Fixed.
Parent directories with shlex-interpreted characters in their names
could be misinterpreted. Removed shlex parsing.
Packagers may want to remove the git history to slim down the package
size, so add an option for using a file 'version' in the klippy
directory to set version without using git.
Signed-Off-By: Lucas Fink <software@lfcode.ca>
Setting the square corner velocity to zero would cause stuttering
during the test if a bed mesh is in effect. It's possible to get the
desired effect by reducing the square corner velocity and setting the
pressure advance lookahead time instead.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't require the config file to specify manual probing. Instead,
allow the user to select manual probing on each ProbePointsHelper
invocation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for writing back the main printer config file with
additional calibration data stored in it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a command that will turn off all heaters in the printer. Run this
command in the default idle_timeout action.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update the document to recommend tuning with decreased acceleration
and with square_corner_velocity disabled. Using this approach makes it
possible to test with significantly higher pressure advance values.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This can be flashed to e.g. the duet wifi using bossac. It requires a
later version as is currently included in the klipper repo (1.8
vs. 1.2). Comms are currently via UART0 only, USB serial is still TBD
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
The Todo.md file has gotten stale, and it is no longer an effective
mechanism for tracking changes. Remove it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add initial support for commands that will forcibly move a stepper
(without updating the kinematic classes with the new position).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The junction_deviation configuration parameter has a number of quirks
that make it difficult to configure. Replace it with a
"square_corner_velocity" configuration parameter.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add M117 and M73 to the list of supported G-Codes.
Also, remove M117 from the list of commands reported by the HELP
command as that command is typically only used to list "extended
g-code" commands.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add basic SPI support and associated documentation.
v2: remove baud rate check, fix baud rate calculations
v3: finish transaction with BSY check, disable SPI when not in use
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
Kevin O'Connor