bd40690bd1
quad_gantry_level: Support retries
...
Support retrying QUAD_GANTRY_LEVEL a configurable number of times
to a configurable tolerance both in the config or as parameters.
- By default keeps original behavior of no retries.
- Adds parameters RETRIES and RETRY_TOLERANCE to QUAD_GANTRY_LEVEL gcode.
- adds config options retries and retry_tolerance to `[quad_gantry_level]`
- issues an error if we are getting worse intead of approaching tolerance
- issues an error if retries were requested but we did not reach the tolerance
in the specified number of retries
Signed-off-by: John "Fess" Fessenden <fess@fess.org>
2019-06-18 12:12:25 -04:00
4681775219
z_tilt: Add RetryHelper
...
add RetryHelper class in prep for implementing retries for both z_tilt
and quad_gantry_level
Signed-off-by: John "Fess" Fessenden <fess@fess.org>
2019-06-18 12:12:25 -04:00
bdf5898891
probe: Allow retries from ProbePointsHelper
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-18 12:12:25 -04:00
20d0bb8354
config: Update tmc5160 block in example-extras.cfg
...
List all the configurable parameters in the tmc5160 example block and
use similar wording as the other tmc drivers.
Also, don't allow DEDGE to be configured as it would just break the
current code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-18 09:41:27 -04:00
494a5b732d
quad_gantry_level: Use new ZAdjustHelper
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-17 11:17:47 -04:00
20851ab3e9
z_tilt: Separate z adjustment code to new ZAdjustHelper class
...
Introduce a new class to perform the low-level Z stepper adjustments.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-17 11:17:47 -04:00
f6864da58b
tmc2208: Add support for using an analog mux to access TMC uarts
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-12 22:14:41 -04:00
88fe2787a9
tmc2208: Separate low-level bit-banging code from MCU_TMC_uart class
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-12 22:06:54 -04:00
47901e57c9
verify_heater: Don't raise a heater error if the heater is off
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-12 22:06:54 -04:00
82b58e46a7
temperature_fan: Remove executable flag from temperature_fan.py
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-10 14:30:48 -04:00
b21a22d744
tmc: Move common TMC stepper driver code to new file tmc.py
...
Move common code from tmc2130.py to tmc.py.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-10 14:29:35 -04:00
10c0da9a6c
tmc2130: Rework remaining config helpers to use mcu_tmc interface
...
Introduce TMCMicrostepHelper and TMCStealthchopHelper helper code that
uses the mcu_tmc interface. Update the callers to use these new
helpers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-10 14:18:58 -04:00
7f34264101
tmc2130: Move TMC virtual endstop code into a new TMCEndstopHelper class
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-10 14:18:58 -04:00
35edc4d63c
tmc2660: Move current setting code to its own helper class
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-10 14:18:58 -04:00
b2729f38a6
tmc5160: Move current setting code to its own helper class
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-10 14:18:58 -04:00
110bbb3843
tmc2130: Move current setting code to its own helper class
...
Concentrate the current setting code into its own TMCCurrentHelper
class.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-10 14:18:58 -04:00
6abe132cf0
tmc2130: Transmit register initialization during connect callback
...
Perform the register initialization directly from TMCCommandHelper and
perform it during the "connect" phase. This unifies the register
setup for the TMC2130, TMC2208, TMC2660, and TMC5160.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-10 14:18:58 -04:00
6947548c17
tmc2660: Use TMCCommandHelper
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-10 14:18:58 -04:00
c76428bd01
tmc5160: Use TMCCommandHelper
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-10 14:18:58 -04:00
1bdd51d575
tmc2208: Use TMCCommandHelper
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-10 14:18:58 -04:00
395c845ca1
tmc2130: Factor out g-code command handlers to their own class
...
Create a TMCCommandHelper class that implements INIT_TMC,
SET_TMC_FIELD, and DUMP_TMC.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-10 14:18:58 -04:00
6a7ddb6bf0
tmc2208: Move get/set_register functions to new MCU_TMC_uart class
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-10 14:18:58 -04:00
ab710cd4de
tmc2660: Move get/set_register functions to new MCU_TMC2660_SPI class
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-10 14:18:58 -04:00
a122d113e8
tmc5160: Use tmc2130.MCU_TMC_SPI for low-level get/set_register access
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-10 14:18:58 -04:00
3becc6cf54
tmc2130: Move low-level get/set_register functions to new MCU_TMC_SPI class
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-10 14:18:58 -04:00
9ce98fd769
tmc2660: Define get_register() method
...
Use a get_register() method instead of get_response(). This makes the
tmc2660 class more similar to other TMC drivers. It also enables
DUMP_TMC to dump all the readable content.
Also, use the tmc2130.get_config_microsteps() helper.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-10 14:18:58 -04:00
2b0251ee99
tmc5160: Rename registers to Registers and fields to Fields
...
Minor change to the code so that it is more similar to the other tmc
drivers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-10 14:18:58 -04:00
5de9f74525
test: Add test cases for tmc drivers
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-10 14:18:58 -04:00
97840f9851
serialhdl: Use reactor mutex in send_with_response()
...
Reduce the delay in send_with_response() by introducing a reactor
mutex to wake the main thread when the response is obtained.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-09 19:12:24 -04:00
30d2ae8f9f
gcode: Eliminate the process_batch() method
...
Allow the callers of process_batch() to directly inspect the gcode
mutex. Those callers can then directly invoke run_script().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-09 18:44:44 -04:00
962f7b98bd
gcode: Convert input handling to use a reactor mutex
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-09 18:44:44 -04:00
afc10400e3
reactor: Be explicit on which handlers are timer_handler vs file_handler
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-09 18:44:44 -04:00
0546c18d27
reactor: Add support for mutexes
...
Add a mutex object that implements simple queing mutual exclusion for
greenlets.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-09 12:55:56 -04:00
61fc57e659
toolhead: Commands should still pause even when sync_print_time
...
If commands are slowly fed to the printer it could cause the number of
queued commands to grow without bound. Be sure to pause the incoming
command stream even if the lookahead queue is empty.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-09 12:35:54 -04:00
d7754a8f93
homing_override: Pass params to template evaluation
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-09 11:14:31 -04:00
8b00580884
gcode_macro: Parse variable_X parameters using ast.literal_eval()
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-07 19:33:31 -04:00
01f3b50e73
idle_timeout: Fix typo causing get_status() to fail
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-07 12:30:42 -04:00
f1c6d04376
filament_switch_sensor: Use template evaluation on gcode
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-07 11:38:43 -04:00
d0be48da74
filament_runout_sensor: Auto load pause_resume module if pause_on_runout enabled
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-07 11:38:43 -04:00
3f4190c792
idle_timeout: Use template evaluation on gcode
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-07 11:38:43 -04:00
e60ee861f8
extruder: Use template evaluation on gcode
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-07 11:38:43 -04:00
27ca159285
gcode_macro: Add a default parameter to load_template
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-07 10:51:57 -04:00
cacb6f4378
klippy: Provide global access to a printer.command_error exception class
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-06 10:22:14 -04:00
49a3083d6a
manual_probe: Add extra checks to catch manual probe not finishing correctly
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-06 10:08:58 -04:00
40f73dd7f4
probe: Check for toolhead movement during activate/deactivate_gcode scripts
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-06 10:08:58 -04:00
df80d96ae6
manual_probe: No need to re-raise an EndstopError
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-06 10:08:58 -04:00
b8c7eb40c5
bed_screws: No need to re-raise an EndstopError
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-06 10:08:58 -04:00
1fd490ddf9
probe: No need to re-raise an EndstopError
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-06 10:08:58 -04:00
67964e71f1
homing: Catch the more generic CommandError during homing
...
Allow the low-level homing code to raise either a gcode.error or an
EndstopError during a fault.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-06 10:08:58 -04:00
e9935e1a41
gcode: No need to re-raise an EndstopError
...
Now that EndstopError and gcode.error use the same underlying
Exception object, it is no longer necessary to translate an error.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-06 10:08:58 -04:00
fess