Automatically clear the information printed at the start of each log
file rollover on a klippy internal restart.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Drop support for M303 and PID_TUNE, and replace it with a new
PID_CALIBRATE command. Move the logic for this command from heater.py
to a new pid_calibrate.py file in the extras/ directory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the probe_z_offset parameter from delta_calibrate and
bed_tilt_calibrate to a z_offset parameter within the probe config
section. It's easier to understand the z offset setting when it is in
the probe config section.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If a z_virtual_endstop is in use, then record the last XY position
that is used when the Z is homed. Use that XY position to report what
change is needed to the z position_endstop.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename the digital_output, pwm_output, and static_pwm_output config
sections to output_pin and move to a new module in the extras/
directory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the code for the static_digital_output config section from
chipmisc.py to a new file in the extras/ directory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It looks like OctoPrint is expecting the result from M114 to be
relative to the last G92 command. Also, introduce GET_POSITION to
report the actual location that the printer is at.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit 9bc4239e now emphasizes the first line of a multi-line error
message, so rework startup_message to conform to that.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Report the first line of a multi-line error message twice - once as
part of the informational content, and once with the "!!" error
prefix.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If a heater falls out of the target range, accumulate the temperature
differences to determine if an error should be raised. This should
make it less likely to report an error for heaters that drift slightly
out of range, and it should make error reporting faster for heaters
that rapidly fall out of range.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
A default of 4 degrees and 10 seconds may be too aggressive - change
the default to 10 degrees and 15 seconds.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for additional carriages on cartesian printers. This is
used by some printers to handle multiple extruders.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Separate out the hd44780 screen drawing from the st7920 code. Use a
layout that takes advantage of the 20 columns. Add custom hd44780
fonts.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Working printer configuration for a Wanhao Duplicator i3 v2.1 and its
clones, including Monoprice Maker Select and Cocoon Create. Includes a
working config for the st7920-based front panel LCD.
Signed-off-by: Andy Ellsworth <andy+github@dar.net>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
I've added the LCD configuration for the Tronxy X5S printer and its
Melzi board and 128x64 LCD. This is tested and works.
I've also added the pins for the encoder, but that is untested.
Signed-off-by: christian mock <cm@tahina.priv.at>
Add support for displaying basic status information on ST7920 and
HD44780 based LCDs that are attached directly to a micro-controller.
Signed-off-by: Marcio Teixeira <marcio@alephobjects.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support low-priority message transmits. This may be useful for bulk
commands that should be delayed util the comms are otherwise idle.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor