Support associating a stepper_kinematics with a trapq. Support
generating steps from a time range on the given trapq.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for building a list of moves in the trapq.c code. Update
the toolhead code so that moves generated from the look-ahead code are
added to that list.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the kinematic position calculation function had an error in it (if
it produces sudden position changes) then it could lead to an infinite
loop in itersolve_gen_steps().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Break up the connect phase into two phases - mcu_identify and connect.
The first phase will contact all the micro-controllers and obtain the
"identify" data dictionaries for them. Once all the micro-controllers
have been contacted, then they can be configured. This fixes an issue
with FIRMWARE_RESTART not working correctly on multi-mcu setups that
use restart_method=command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Wait in the M25 command handler until the work_handler() background
timer fully exits. This ensures that subsequent g-code commands (such
as M27 or M24) will correctly report a paused state.
Reported by @foosel.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The initial clock measurement wasn't properly implementing a small
delay between clock queries. Fix the pause() call so there is a small
delay between queries.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some print start scripts may extrude at a position slightly higher
than the first z layer height. Tweak the backwards z test to reduce
the chance of the tuning test ending prematurely.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
PR #1970 introduced a new parameter, controlling the default behavior of the safe_z_home-module. To avoid unexpected changes, the default of the move_to_previous is now defaulted to False.
Signed-off-by: Nils Friedchen <Nils.Friedchen@googlemail.com>
If '[stepper_x]' and/or '[stepper_y]' have a 'position_min' that is
non-zero, and '[safe_z_home] home_xy_position' is '0,0'; then the 'G28'
command will _not_ move to '0,0'; but stay at 'position_min' during the
Z endstop test.
This fix corrects this issue.
Signed-off-by: Jason S. McMullan <jason.mcmullan@gmail.com>
Below off_below the fan will be turned off. When configured correctly this
can prevent stalling, which may lead to overheating and failed fans. To
simplify calibration and use of this setting, off_below is applied in the
input duty cycle domain, prior to any scaling due to e.g. max_power.
Signed-off-by: Nicholas Seckar <nseckar@gmail.com>
When reducing the maximum speed due to the max_accel_to_decel setting,
move velocity limits must still be propagated. Otherwise, the
trapezoid move planner may produce moves with velocity jumps.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Once a hop is performed, it will only be re-issued if the z-axis has been
moved in the meantime. Usually it is only moved by a z-homing so doing so
will cause safe_z_home to do the hop on the next homing action.
When z-axis is homed, x and y positions are known. When setting this
boolean option, these are set back to their last positions.
Whenever a hop is specified it is re-issued after the Z axis has been
homed. This is especially necessary when a pressure-based probe is used.
Also, the module decides if a hop is necessary, based on either a known
Z position or a flag that is set whenever the motors are disabled.
Signed-off-by: Nils Friedchen <Nils.Friedchen@googlemail.com>
Previously, when a sercom pin specified the mcu (myname:PIN), it would result in a pin enumeration error.
Signed-off-by: John Jardine <john@gprime.net>
R Still missing, also might be somewhat dirty since code is converted
into G1 commands.
Signed-off-by: Aleksej Vasiljkovic <achmed21@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
During a "drip feed" move, both the move's maximum speed and maximum
acceleration may be limited by the kinematics.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor