Avoid using the "low-level" library timing utilities. This is in
preparation for using SysTick as part of the timer implementation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the definition of SERIAL_BAUD to the main src/Kconfig file. Only
show this as an option if the user selects the ability to configure
low-level options.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some older versions of gcc need the __always_inline directive in order
to inline timer_read_time. Inlining that function is important for
performance on the stm32f1.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
As long as timer_read_time() is inlined, I get better performance with
gcc -O2 optimization. The binary is also dramatically smaller and O2
better matches the other platforms.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's possible for the code to stay in the timer irq for up to 100ms,
so serial irqs should have a higher irq priority to prevent them from
being starved. (The timer code disables irqs during event dispatch,
so serial irqs would only be permitted between events anyway.)
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The SPI interface needs to be enabled and configured to the correct
settings of a given oid before CS is asserted. The new function
spi_prepare() allows ports to do that.
This port only introduces the new function in all ports with no
implementation and adds the call to the Klipper generic firmware code.
That means everything still works as before. Ports need to be changed
to fix the underlying issue.
Discussion about the motivation here:
https://github.com/KevinOConnor/klipper/pull/453#issuecomment-403131149
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
Add basic SPI support and associated documentation.
v2: remove baud rate check, fix baud rate calculations
v3: finish transaction with BSY check, disable SPI when not in use
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
For some reason, the upper two pin definitions were missing. Found while
writing the port documentation.
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
The gpio_out_toggle() function in the sam3x8e and stm32f1 code was
only valid if it was called with irqs disabled.
Commits 018c5daa and 9c52ad43 enabled the lcd code which called
gpio_out_toggle() with irqs enabled. This could cause corruption of
the gpio state.
Introduce a gpio_out_toggle_noirq() function that will only be invoked
with irqs disabled, and fix gpio_out_toggle() on sam3x8e and stm32f1
so that it safe to call even if irqs are enabled.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Extract out common code from avr/serial.c, sam3x8e/serial.c, and
stm32f1/serial.c into a new generic/serial_irq.c file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
With the optimized timer_read_time() it is no longer necessary to
implement custom timer dispatch code - use the generic mechanism in
timer_irq.c. This simplifies the code and provides a small
performance increase.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Implement 32bit timer conversion without disabling interrupts. This
uses the 16th bit of timer_high as a rollover detection flag.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a fully functional STM32F1 port, currently mostly targeting STM32F103
microcontrollers. This requires an 8 MHz XTAL. The maximum possible step rate
is around 282K steps per second.
This uses stm32flash to burn the firmware. The bootloader needs to be started
by setting BOOT0 to 1 and resetting the MCU. There is no automatic bootloader,
unlike on Arduino.
Signed-off-by: Grigori Goronzy <greg@kinoho.net>
Kevin O'Connor