Commit Graph

183 Commits

Author SHA1 Message Date
Kevin O'Connor 9aadc3c7fa docs: Also note that driver_VSENSE was removed from tmc2660 driver
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-22 22:40:42 -04:00
Kevin O'Connor 871e028c27 config: Document the [include] directive
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-22 20:48:15 -04:00
Kevin O'Connor 3945905420 config: Minor rearrangement of example-extras.cfg
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-22 20:46:37 -04:00
Kevin O'Connor efab177645 docs: Note tmc2660 driver_HEND default change from 6 to 3
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-22 20:41:32 -04:00
Matt Baker f2fbe98454 bed_mesh: enable relative offset bed meshes (#1323)
Adds parameter for bed meshes to be adjusted relative to a probed point
during calibration. This allows the probe z offset to be ignored for
probes that are not stable over time (for example, the thermal drift of
inductive probes). An endstop other than the probe is then necessary to
determine the bed-nozzle offset.

Signed-off-by: Matt Baker <baker.matt.j@gmail.com>
2019-03-21 10:39:22 -04:00
Kevin O'Connor d3f6dad853 controller_fan: Allow multiple controller_fan sections to be defined
It may be necessary to define multiple fans, so allow each config
section to be named.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-10 13:57:01 -04:00
Kevin O'Connor 19c7955f2a config: Improve the description of z_tilt z_positions
Reported by @sensille.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-10 12:24:34 -04:00
Rui Caridade 5c0a2479be screws_tilt_adjust: Add new screws_tilt_adjust tool (#1367)
Signed-off-by: Rui Caridade <rui.mcbc@gmail.com>
2019-03-08 11:47:17 -05:00
Kevin O'Connor fcaa75f014 config: Update default spi speed in tmc2660 description
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-08 11:27:50 -05:00
Kevin O'Connor 563bc37073 tmc2130: Rename driver_BLANK_TIME_SELECT to driver_TBL
Use the field names from the trinamic specification.  This makes the
field similar to all the other driver_XXX config options.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-08 11:25:19 -05:00
Florian Heilmann e96b71a9a3 tmc2660: Use helper functions for register access and simplify TMC2660 parameters
sense_resistor is now a mandatory parameter for tmc2660 blocks. Duet2 users should use a value of 0.051

Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2019-03-08 11:04:14 -05:00
Florian Heilmann 4541f16cd9 tmc2660: Add vsense_resistor config parameter
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2019-03-08 11:04:14 -05:00
Kevin O'Connor 47d51d8613 config: Update verify_heater description
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-08 10:55:46 -05:00
Kevin O'Connor d62a41b930 manual_stepper: Add support for moves with acceleration
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-03 13:38:10 -05:00
Arksine 69491e2dab filament_switch_sensor: update documentation
Signed-off-by:  Eric Callahan <arksine.code@gmail.com>
2019-03-01 00:45:51 -05:00
Kevin O'Connor c8d7e28a35 atsamd: Add support for programming SERCOM pins
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-01 00:40:44 -05:00
Douglas Hammond b6589406d4 temperature_sensor: Add generic temperature sensor support
Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-26 13:15:56 -05:00
Douglas Hammond 3887ad4fce heater: Support generic gcode_id registration for sensors
Support reading a "gcode_id" parameter from heater/sensor config
sections.

Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-26 12:07:00 -05:00
Arksine f7d8854587 bed_mesh: simplify configuration
The 'bed_shape' option has been removed.  The user will enter a 'bed_radius' if they have a round be, otherwise they should enter 'min_point' and 'max_point'.  When the bed is round the user should supply a 'round_probe_count' option, otherwise just 'probe_count'.

Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-02-25 13:34:14 -05:00
Kevin O'Connor 80c8bd8b4d bed_screws: Add a helper tool for leveling bed screws
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-24 00:49:47 -05:00
Kevin O'Connor 834b9e3d92 config: Warn that cycle_time may not match when using hardware_pwm
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-19 13:19:32 -05:00
Kevin O'Connor cc4ecef88b mcp4018: Add initial support for the mcp4018 digipot
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-16 08:16:37 -05:00
nopbit 0f674ef407 tsl1401cl_filament_width_sensor: Filament Width Sensor Support (#1132)
Support added for filament diameter sensor. Sample configuration parameters added to example-extras.cfg.

Signed-off-by: Mustafa YILDIZ <mydiz@hotmail.com>
2019-02-14 10:13:48 -05:00
KevinOConnor c6d1d1bd8c
Merge pull request #1242 from john--/pr_generic_heater
Generic Heater Support
2019-02-14 10:08:26 -05:00
John Jardine 6316b2c1b6 Generic Heater Support
Adds the ability to register a custom/generic heater through a new extra called heater_generic.
This takes a gcode_id that is reported by M105. Adds a new command to set the temperature for any heater using the syntax:
SET_HEATER_TEMPERATURE HEATER=<heater_name> TARGET=<target_temp>

Signed-off-by: John Jardine <john@gprime.net>
2019-02-14 01:15:11 +00:00
Kevin O'Connor 98ed462865 spi_software: Implementation of software spi
Signed-off-by: Matt Janus <FragginRight@variabl.es>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-13 11:52:20 -05:00
Kevin O'Connor 2d7c3a84ee manual_stepper: Add an "extras" module for manually controlling a stepper
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-12 13:38:13 -05:00
Kevin O'Connor 345a5f4e1f bltouch: Increase default pin_move_time from 200ms to 675ms
Use the same pin move time that Marlin uses.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-04 18:02:53 -05:00
Arksine cdcc320710 bed_mesh: add support for round beds
Signed-off-by:  Eric Callahan <arksine.code@gmail.com>
2019-02-02 23:29:00 -05:00
Arksine 893cbbab83 pause_resume: update documentation
Add updates to example-extras.cfg and G-Codes.md documenting pause_resume.  Also add M600 (filament change) to sample-macros.cfg.

Signed-off-by:  Eric Callahan <arksine.code@gmail.com>
2019-01-28 11:23:52 -05:00
Kevin O'Connor 7327394c50 adc_temperature: Add support for linear interpolation of resistances
Add support for performing linear interpolation between a set of
measured temperature/resistance pairs.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-21 21:28:25 -05:00
Kevin O'Connor 8a97bc592b bltouch: Add a pin_up_touch_mode_reports_triggered config option
Rework the undocumented test_sensor_pin config option into a
pin_up_touch_mode_reports_triggered option and document it.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-21 09:52:11 -05:00
Kevin O'Connor e36122797b bltouch: Attempt to verify that the probe raises after each probe attempt
Query the bltouch state during the pin_up command to try and verify
that the probe does actually retract.  This may be useful to detect if
the bltouch enters into an "error" state.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-21 09:52:11 -05:00
Master92 a27838bc05 controller_fan: Add support for a fan cooling the controller-board (#1070)
Whenever a stepper driver or a heater becomes active, it is desirable to turn on a fan cooling the associated parts on the controller board. This module implements such a fan that turns on whenever a stepper or specified heater turns on, decelerates to a configurable speed when all of the watched parts turn off, and returns to an off-speed, when a user-defined timeout is met.

Signed-off-by: Nils Friedchen <Nils.Friedchen@googlemail.com>
2019-01-10 12:12:15 -05:00
Yannic Schröder d015209388 docs: Add guide for sensorless homing (#1004)
Signed-off-by: Yannic Schroeder <schroeder@ibr.cs.tu-bs.de>
2019-01-07 10:39:16 -05:00
Kevin O'Connor c2086796bf mcp4728: Add initial support for the mcp4728 i2c dac chip
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-02 18:17:56 -05:00
Alec B. Plumb 59e9b6562f respond: An extra for sending messages to the printer host. (#1053)
I have made one change to `gcode.py` to support quoted parameter
values.

I have added support for the basic `M118` command (see
https://reprap.org/wiki/G-code#M118:_Echo_message_on_host). I have
also added a `RESPOND` command that takes extended parameters.
`ECHO` might be a better name than `RESPOND` but is already defined
in `gcode.py`.

Signed-off-by: Alec B. Plumb <alec@etherwalker.com>
2019-01-02 17:45:35 -05:00
Kevin O'Connor 531575651c bltouch: Document that bltouch "clones" may not work correctly
There is concern that the bltouch.py module may not perform adequately
on some bltouch "clones".  Document that.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-12-18 17:12:44 -05:00
Kevin O'Connor ccc25a03d5 bltouch: Add a config option to disable the bltouch sensor test
It appears some bltouch "clones" do not report the probe as triggered
when put in "touch mode" while the pin is raised.  Add a config option
to allow users to disable the test.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-12-16 11:06:41 -05:00
Kevin O'Connor 44aa5def73 bltouch: Allow the pin_move_time to be configured
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-12-04 10:34:54 -05:00
Arksine 581b1439f3 config: Update bed_mesh in example-extras.cfg
Update documentation about the fade options. Also inform the user that it is recommended to home toward the center of the print area when using a probe for z homing.

Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2018-11-30 11:37:21 -05:00
Kevin O'Connor 824e55d75a bltouch: Add initial support for a bltouch "extras" module
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-30 11:34:20 -05:00
Kevin O'Connor 147d805231 mcp4451: Use bus.py helper code for i2c
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-24 00:33:22 -05:00
Kevin O'Connor e5150fe187 uc1701: Add support for SSD1306 in i2c mode
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-23 22:04:06 -05:00
Kevin O'Connor e231ac7422 uc1701: Add support for SSD1306 displays
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-21 20:45:53 -05:00
Kevin O'Connor 9ba94ded9e tmc2660: Use bus.py helper code for spi
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-21 12:12:31 -05:00
Jiri Dobry e541466591 servo: This patch create ability to enable/disable attached servo. (#880)
Cheap mechanical servos have small flickering. When this servo stay on one position, this flickering slowly destroy internal potentiometer and make servo unusable. Many mechanisms need servo only to change position. Therefore I create this minor path to enable/disable servo. It stop pulses for this servo, that's all.

Corresponding G-code is:
SET_SERVO SERVO=config_name [WIDTH=] [ENABLE=<0|1>]
SET_SERVO SERVO=config_name [ANGLE=] [ENABLE=<0|1>]

For example:
SET_SERVO SERVO=touch ANGLE=80 ENABLE=1 ; enable servo and set position
G4 P200 ; wait 200ms
SET_SERVO SERVO=touch ENABLE=0 ; disable servo

This patch add one option to servo configuration:
enable: <False/True> # default True

It not have impact to user code existing already because it is optional parameter and default value is same as original behavior.

Signed-off-by: Jiri Dobry <jdobry@centrum.cz>
2018-11-14 09:38:09 -05:00
Florian Heilmann 4372d1812c Implement idle event support in the TMC2660 extra
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2018-10-28 18:45:49 -04:00
Florian Heilmann f57c29442c Add SX1509 extra
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2018-10-27 10:34:28 -04:00
Florian Heilmann b6bf455155 tmc2660: Add endstop phase detection functionality to TMC2660 extra (#816)
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2018-10-24 16:01:12 -04:00
Kevin O'Connor 1e71909d02 endstop_phase: Add support for an ENDSTOP_PHASE_CALIBRATE command
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-16 13:09:49 -04:00
Kevin O'Connor def524bdf4 endstop_phase: Add support for detecting phase via TMC stepper drivers
The Trinamic stepper motor drivers are capable of reporting the
stepper phase - add support for using that capability to the
enddstop_phases module.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-16 13:09:23 -04:00
Kevin O'Connor a2df01b88e endstop_phase: Move endstop phase homing code to new "extras" module
Move the endstop phase tracking code from stepper.py to a new
extras/endstop_phase.py module.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-16 13:09:23 -04:00
Chris Whiteford c5d94a74a5 servo: Adding support for startup value for servos (#676)
Signed-off-by: Chris Whiteford <github@chrisandtennille.com>
2018-10-05 14:35:38 -04:00
LazaroFilm 822616ae7f docs: Spelling error corrected in bed mesh comment (#735)
The comment for the algorithm setting had a spelling error, it said:
[...]May be either "langrange"[...]
Removed the n.

Signed-off-by: Victor Lazaro <lazarofilm@gmail.com>
2018-10-04 12:48:27 -04:00
Kevin O'Connor 1940ba7062 config: Minor indentation fix to comments in example-extras.cfg
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-01 11:12:30 -04:00
Kevin O'Connor a698aef29b config: Note probe activate/deactivate must not move the toolhead
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-01 11:12:30 -04:00
Kevin O'Connor c5d4e14298 probe: Infer position_endstop when using probe:z_virtual_offset
Don't require (or permit) the user to specify a stepper_z
position_endstop when using the probe:z_virtual_offset mechanism.  In
that case the position_endstop should always equal the probe's
z_offset - so no need to have the user specify it.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-01 11:12:30 -04:00
Kevin O'Connor 348a41c325 bed_tilt: Remove special probe:z_virtual_endstop handling
Remove the code to calculate and track the z_offset via
position_endstop updates.  It's simpler to always save and restore the
calculated z_adjust.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-01 11:12:30 -04:00
Kevin O'Connor 33887b8c39 probe: Support manual probing at runtime
Don't require the config file to specify manual probing.  Instead,
allow the user to select manual probing on each ProbePointsHelper
invocation.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-01 11:12:30 -04:00
Kevin O'Connor b112cac47a config: Fix typo in gcode_macro default_parameter description
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-09-30 12:11:07 -04:00
Janar Sööt 68dc28580f gcode_macro: default parameter values
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-09-30 11:53:10 -04:00
Kevin O'Connor cf79b3c342 config: Note gcode_macro string formatting in example-extras.cfg
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-09-26 08:25:44 -04:00
Kevin O'Connor 439f6684be config: Move some sections around in example-extras.cfg
Move the quad_gantry_level description closer to z_tilt section.  Move
the force_move section closer to the homing_override section.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-09-26 08:16:40 -04:00
Kevin O'Connor 174754299a heater: Add new TURN_OFF_HEATERS command
Add a command that will turn off all heaters in the printer.  Run this
command in the default idle_timeout action.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-09-18 16:01:07 -04:00
Maks Zolin e3a49dc692 quad_gantry_level: Add gantry leveling (ruled hyperbolic parabola correction) (#631)
Signed-off-by: Maks Zolin <mzolin@vorondesign.com>
2018-09-12 08:33:20 -04:00
Boffgithub 0c0087ce42 config: Update example-extras.cfg (#641)
Just correcting a couple of spelling errors I noticed.

Signed-off-by: Ben Warren <boffdroid@gmail.com>
2018-09-12 08:13:12 -04:00
Florian Heilmann 947a7b2b0f tmc2660: Implementation of TMC2660 extra (#621)
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2018-09-11 12:34:05 -04:00
Kevin O'Connor a8d4a7ef46 config: Be clear that multi-line parameters must use indentation
Also, be clear that probe points are nozzle coordinates (not probe
coordinates).

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-09-02 14:40:26 -04:00
Arksine 40b7ba5111 probe: Add ability to multi-sample points to ProbePointsHelper
Signed-off-by:  Eric Callahan <arksine.code@gmail.com>
2018-08-29 12:01:19 -04:00
Kevin O'Connor 4acda88e8d docs: Fix spelling error in example-extras.cfg
Fix "interally" spelling error - reported by @bistory.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-28 15:36:53 -04:00
Kevin O'Connor ca7a80a946 tmc2208: Initial support for configuring TMC2208 drivers
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-27 12:51:27 -04:00
Janar Sööt 65f0fd6238 display menu module for klipper
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
2018-08-20 22:33:05 -04:00
Arksine 3387cccdcf bed_mesh: move probe x and y offsets to the [probe] module
All probe offsets are now passed to the finalize() callback in the ProbePointsHelper Class.

Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2018-08-19 16:52:23 -04:00
Boffgithub 08aacec0b2 config: Update example-extras.cfg (#544)
Changed 'endstop' to 'stepper' in 'multi-steppers axes' section

Signed-off-by: Ben Warren <boffdroid@gmail.com>
2018-08-19 10:15:48 -04:00
Kevin O'Connor 1b07be070b heater_fan: Allow multiple heaters to be defined for a heater_fan
Support the case where a single cooling fan is used with multiple
extruders.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-17 10:20:12 -04:00
Arksine f337fb1802 config: update examples-extra.cfg to include the bed_mesh module
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2018-08-17 09:22:55 -04:00
Kevin O'Connor 43179d7b6c config: Minor changes to example-extras.cfg documentation
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-03 13:00:40 -04:00
Kevin O'Connor c0c892d524 force_move: Add support for FORCE_MOVE command
Add initial support for commands that will forcibly move a stepper
(without updating the kinematic classes with the new position).

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-07-26 12:44:07 -04:00
Kevin O'Connor 63dffd9307 spi_temperature: Provide a default value for spi_speed
All of the Maxim chips support a 4Mhz spi transfer rate, so use that
as a default spi speed.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-07-24 15:49:14 -04:00
Kevin O'Connor 5b124d59f2 spi_temperature: Remove spi_mode parameter
All of the Maxim chips can use SPI mode 1, so no need to configure it.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-07-24 15:47:17 -04:00
Kevin O'Connor eba252d3fd thermocouple: Add initial support for common SPI temperature sensing chips
Signed-off-by: Petri Honkala <cruwaller@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-07-24 11:16:05 -04:00
Kevin O'Connor acefe26e0f idle_timeout: Move timeout handling from toolhead.py to new extras module
Move the "motor_off_timeout" tracking to a new module in the extras/
directory.  This makes it easier to customize the idle timeout
behavior.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-07-16 10:32:48 -04:00
Kevin O'Connor 94dc8167c9 z_tilt: Don't default "points" parameter to "z_positions" parameter
It's rare to have all the Z stepper locations directly under the
printable surface, so using z_positions for points is not a good
default.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-07-15 10:30:27 -04:00
Kevin O'Connor 21563c5965 config: Minor updates to example-extras.cfg
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-07-12 12:18:31 -04:00
Kevin O'Connor d725160706 mcp4451: Add initial support for programming the mcp4451 on lpc176x
Add support for programming smoothieboard current.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-06-29 21:20:12 -04:00
Arksine 696ee69f2c config: update example-extras.cfg to include uc1701 display
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2018-06-27 19:46:38 -04:00
Kevin O'Connor f08a0c5e93 lcd_st7920: Use a longer delay at the start of each command/data
It appears the st7920 requires a longer delay when switching from
command to data mode (and vice-versa).  Slower MCUs don't show a
problem because the klipper command processing time results in a
sufficient delay.  However, some of the faster MCUs can process
klipper commands fast enough that the next st7920 transfer is sent too
fast.  Add an additional delay to account for this.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-06-22 23:47:09 -04:00
Kevin O'Connor d94c856118 display: Allow the ST7920_DISPLAY parameter to be configured
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-06-21 09:58:35 -04:00
Hans Raaf e110e1fecc homing_override: Add axes config parameter
Added a config parameter to define the homing override axes. This way
one can still home x and y axis without the z-probe cycle coming in the
way.

Signed-off-by: Hans Raaf <hr-klipper@oderwat.de>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-06-11 20:41:18 -04:00
Kevin O'Connor c38a63d4db gcode_macro: Add the ability to define custom g-code macros
Add the ability to add a custom g-code command that in turn executes
one or more configured g-code commands.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-05-25 12:40:06 -04:00
Kevin O'Connor 5ae22a5e51 tmc2130: Allow the PWMCONF register to be configured
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-05-25 11:38:27 -04:00
Kevin O'Connor 1e6fa5722a tmc2130: Initial support for sensorless homing
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-05-25 11:38:23 -04:00
Kevin O'Connor 3799f40f29 tmc2130: Configure stealthchop velocity limit
Change stealhchop config option to a stealthchop_threshold
configuration option.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-05-25 11:38:12 -04:00
Kevin O'Connor c4fe43ffce tmc2130: The default TOFF time should be 4
The recommended TOFF time in "standalone mode" according to the
tmc2130 is 4, so use that as the default.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-05-24 10:44:45 -04:00
Kevin O'Connor 3025638b9b z_tilt: Add support for Z_TILT_ADJUST
Add new module to support independent adjustments to multiple Z
steppers to account for bed tilt.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-05-22 22:23:44 -04:00
Kevin O'Connor 680c92de40 tmc2130: Add initial support for TMC2130 stepper motor drivers
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-05-20 18:03:06 -04:00
Kevin O'Connor 2740838b2e fan: Allow the fan shutdown_speed to be configured
Add a shutdown_speed config option to fans so that users can specify
the speed on a shutdown event.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-05-18 19:12:03 -04:00
Douglas Hammond 5712283e91 Add temperature controlled fans
Signed-off-by Douglas Hammond  <wizhippo@gmail.com>
2018-05-17 12:50:21 -04:00
Michael Barbour bf3c41cd06 temperature_fan: Add support for temperature-triggered fan.
Signed-off-by: Michael Barbour <barbour.michael.0@gmail.com>
2018-05-10 19:32:23 -04:00