Change all the example config files to use either 0 or 999999 for
stealthchop_threshold (as is recommended in the TMC_Drivers.md
document).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for the Creality CR-30 'PrintMill', and its base board,
the Creality v4.2.10.
Add them to the `test/klippy/printers.test` test suite
Signed-off-by: Jason S. McMullan <jason.mcmullan@gmail.com>
A working configuration example for Tronxy X5SA Pro printer (https://tronxy.com/x5s-series/x5sa-pro.html) with no Touchscreen funcionalities because separated LCD firmware needed.
Silent TMC2225 drivers soldered on board.
The Self-levelling plate sensor is a blue Tronxy XY-08N model.
Direct Drive is a Titan Extruder Clone "3:1" gear ratio.
Signed-off-by: Morgan Barresi <morganfw@gmail.com>
Improvements and fixes based on feedback:
* Make speeds and limits more conservative
* Fix Y endstop position
* Improve IR bed leveling
* Fix filament runout pin
Signed-off-by: Justin Schuh <code@justinschuh.com>
Create a sample-aliases.cfg with all the aliases that are currently
hardcoded in the klippy.pins.py module.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This adds support for BMP280 and BME680 sensor ICs,
along with fixing calibration data readout for BME280.
Gas sensor readout for the BME680 is just the raw compensated value.
To get actual meaningful values, more research is needed.
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
A working configuration example for Hiprecy Leo printer (https://www.hiprecy.com/product/402/) with no Touchscreen funcionalities because separated LCD firmware needed.
TMC2130 SPI drivers.
The Self-levelling plate sensor is PINDA probe type
Direct Drive is a BMG "3:1" gear ratio
Signed-off-by: Morgan Barresi <morganfw@gmail.com>
There are two fan pins on Robin Nano 3 and the fan1 pin is PC14, not PB1.
PB1 pin that was in config example is used for the fan2 output.
Signed-off-by: Oleksii Zelivianskyi <alexeyzel@gmail.com>
we just found a small problem: Some people have slightly higher endstop positions, which caused them to have a move out of range during probe calibrate.
Signed-off-by: Christoph Frei <fryakatkop@gmail.com>
Fixed bltouch offset and bed_mesh mesh_min/max to account for offset.
The former was defined in the wrong coordinate, as the origin starts from the SW. The latter did not include the offset and caused an error. Technically the offset allows mesh_max up to (239.3, 253).
Signed-off-by: Ben Kaye <benkaye001@gmail.com>
Add generic-bigtreetech-gtr.cfg to printers.test. Add definitions for
thermocouple and temperature_mcu.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Added Ender 3 Max config. Based off the configs from ender6, ender3-v2, and ender3. Also contains optional BLTouch parameters.
Signed-off-by: Chad Schwieterman <chad.devops@gmail.com>
The Lulzbot TAZ6 single extruder configuration had an XY position for
z homing that did not match the factory firmware, and was off center
enough to cause the extruder to crash into the home button trim
sometimes when homing. This commit changes the printer config so
that the XY position for Z homing matches the original Marlin firmware
for this printer.
The Lulzbot TAZ6 single extruder configuration had an bed_tilt points
that did not match the factory firmware, and were off enough that the
nozzle (used for probing on this printer) could slip off the edge of
the probe point or miss it entirely. This commit changes the printer
config so that the coordinates for bed_tilt calibration match the
original Marlin firmware for this printer.
For the Lulzbot TAZ6 single extruder config, use 'gear_ratio' and
'rotation_distance' to configure the extruder.
The rotation distance is based on effective circumference of the hobbed
bolt based on the original Marlin firmware for the TAZ6 single-extruder,
and the gear ratio was determined by simply counting the number of
teeth on the pinion and spur gears.
Signed-off-by: Steven T. Snyder <github@steventsnyder.com>
Add support for automatically calculating the internal step_distance
from new config parameters - rotation_distance, microsteps,
full_steps_per_rotation, and gear_ratio.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Minor indentation changes and remove default values for heater_fan.
Add to printers.test test cases.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Adds config for the Monoprice Select Mini v2 cartesian printer. I have
successfully tested the configuration.
Signed-off-by: Kilian Neuner <github@9-r.net>
Add an 'mcu' option to the board_pins config and use that to specify
the name of the mcu to apply the aliases to. Support applying the
aliases to multiple mcus.
Add support for any number of options starting with an "aliases_"
prefix.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move all the config reference information from files in the config/
directory to a new Config_Reference.md document.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Config should not specify a default pressure_advance. Note limit on
current with old 30 Ohm Z-motor.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Fixing alias for thermistors to be on the host rather than the PRU.
Moving the D1W alias from PRU MCU to host MCU.
Signed-off by Jon Charnas <goeland86@gmail.com>
Corrected the diag1_pin numbers. Useful for anyone copying and pasting the lines. Its something really easy to look over and can lead to some hair pulling from the time wasted trying to troubleshoot why the tmc diag pin error from Klipper.
Signed-off-by: Juan Moreno <uncholowapo@gmail.com>
Adding board_pins section.
Added linux host MCU board pin aliases for endstops.
Also added a sample filament switch sensor config.
Signed-off-by: Jon Charnas <goeland86@gmail.com>
From July 2020, Ender 3 Pros came with a 32-bit Creality 4.2.2 board, similar to the Ender 3 V2. Unlike the Ender 3 V2, it comes with the ST7920 LCD screen and HR4988 steppers. Using the config file already in Marlin source, I came up with this klipper config file.
Signed-off-by: Matthias Liffers <m@tthi.as>
The following parameters have been tweaked:
- X endstop position has been set to -2, as per original marlin cofig
- Second Z axis disabled by default (this must be purchased as an
add-on)
The comment at the top of this file has also been modified to describe
the difference between this (old) model and the new (rebranded) Tevo
Tarantula pro.
Signed-off-by: Oliver Fawcett-Griffiths <olly@ollyfg.com>
By homing the y axis before the x axis, the nozzle will not touch the
plastic cover of the bed heater cable.
Signed-off-by: Yannic Schroeder <schroeder@ibr.cs.tu-bs.de>
menu.cfg:
- jinja2 template scripting
- new Setup menu
- new Calibration menu
menu:
- redesigned menu code
- jinja2 support
- option to reverse menu up and down directions
- functionality set to support menu injection from other modules
- a new way of defining menu hierarchy
- other adjustments
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
Using the setup_start_value() method avoids the PWM output line
transitioning to an intermediate state prior to setting the initial
value.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add user-configurable contrast, vcomh (affects "smearing"), and invert options for SSD1306/SH1106 type OLED displays.
Signed-off-by: James Esau <james_esau@hotmail.com>
Input shaping can help to reduce printer vibrations due to resonances
and eliminate or reduce ghosting in prints.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
This commit allows to modify the icons (or glyphs) in the displays that
support it. Existing icons can be modified and new icons can be added via
a [display_glyph] section in the config.
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
Option for using the current diameter instead of nominal while the first measurement isn't in place
Signed-off-by: Matthias Pabel <matthias.pabel@hs-augsburg.de>
Add config file to printers.test. Fix errors in config and unify
settings with the mini-e3-v1.2 config.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This is a basic config example for a SKR Mini E3 v2.0, the pinouts are different than the 1.2 and requires different compile options, so worth having an example.
Signed-off-by: Paul Greidanus <paul@majestik.org>
This gives it parity with heater_fan. Also change the default speed from
max_power to 1.0, since it is already scaled by max_power in set_speed.
Signed-off-by: Adrian Keet <arkeet@gmail.com>
Always disable the PWM after each command sent. Automatically trim
the command duration so the PWM disable doesn't increase the total
pulse time (when the duration is 200ms or greater).
Track the ideal command end time separately from the pwm transmit time
and only delay toolhead moves to this ideal time.
Update verify_state() to automatically schedule the check using the
time of the last sent command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor