Rename try_load_module() so that it uses consistent naming for
"printer objects". Change the function to raise an error by default
if the specified module does not exist.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The heater logic is an independent module that does not need to be
treated as part of the "core" klipper code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The caller can now determine which steppers are connected to cartesian
Z movement via the new stepper.is_active_axis() method. It is
therefore no longer necessary for the kinematic code to identify these
steppers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The STEPPER_BUZZ command needs to know if the axis is using radians
instead of millimeters so that it can move a more appropriate
distance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The print_time parameter of heater.set_temp() is not currently used
and it isn't necessary to flush the look-ahead queue just get the
print_time. Remove the parameter from heater.set_temp() to avoid
flushing the look-ahead queue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The builtin Tn command is not sufficiently flexible to control some
multi-extruder printers. Remove the command and encourage users to
define individual gcode_macros for each Tn instance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Implement the pressure advance calculations while performing the
definitive integral calculations. This simplifies both the
extruder.py and kin_extruder.c code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the extruder lookahead method is no longer used it can be
removed from the toolhead and extruder classes.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support averaging the extruder position over a time range to "smooth
out" the velocity changes that occur during pressure advance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for kinematic functions that calculate step times based on
a range of the motion queue. This requires adding additional pause
times when fully flushing the motion queue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update code that modifies the low-level kinematics handlers to first
call toolhead.flush_step_generation().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename calc_position() to calc_tag_position() and have it calculate
the value of the position from the last stepper set_tag_position()
call. This enables the calc_tag_position() code to be more flexible
as it can be run with arbitrary positions.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the PrinterStepper and MCU_stepper classes have been merged,
there is no need for the add_to_endstop() method.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Directly disable all the stepper motors on a global motor_off() from
the StepperEnable() class in stepper_enable.py. This simplifies the
toolhead and kinematic classes.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
No longer allow the primary extruder to be named "extruder0". This
avoids internal and external confusion between the printer objects and
config section names.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Do not apply max_extrude_cross_section check, and do apply
extrude_only_xxx checks to Z only moves that also extrude. Some
printer start scripts will prime the extruder while moving the Z.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Calculate the ratio of axis distance to total move distance (axis_d /
move_d) and store in a new member variable axes_r. This avoids
needing to recalculate the value in other code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that all callers use the trapq system to queue moves, it is no
longer necessary to individually allocate and fill a 'struct move'.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that all kinematics use the trapq system, there is no need to call
into the kinematics on each g-code move.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that homing is implemented via "drip moves", it is no longer
necessary to round the homing speed and it is no longer necessary to
add a delay for cpu processing time.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Due to the corexy kinematics, the individual steppers may have a
velocity of sqrt(2) times faster than the cartesian velocity _and_ can
have an acceleration of sqrt(2) times faster. Make sure to calculate
in the higher acceleration.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow an arbitrary gcode_id to be supplied during heater setup. This allows future extras to register additional IDs beyond B, and T#.
Signed-off-by: John Jardine <john@gprime.net>
Commit 459e5219 added a special case to the boundary checks to permit
homing moves. In some cases, the second home retract could also be
outside the normal boundary checks - extend the special case to also
permit that move.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some users increase max_extrude_cross_section to avoid issues with
some slicers. However, increasing that value also increases the
defaults for the max_extrude_only parameters which is not obvious.
Base the max_extrude_only defaults only on the configured nozzle
diameter.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
When a delta printer has different arm lengths or different endstop
positions then the homing position falls outside of the normal
printable area. Add a special check to the range checking code to
permit this move instead of homing to a position near the actual
homing position.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the logic for performing the second home from the kinematics
classes to the generic homing code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit b0d859f2 introduced a second_homing_speed parameter, and it
also changed the retract speed. Revert the retract speed change (use
homing_speed when the head retracts).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit b0d859f2 introduced a second_homing_speed parameter; that
parameter needs to also be constrained to the max_z_velocity.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the "stable position" logic from the delta.py kinematics code to
the delta_calibrate.py calibration code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If an arm is nearly parallel to the bed then that tower's carriage may
have a velocity up to 3 times greater than the toolhead's maximum
velocity (relative to the print). Take that into account when
calculating the stepper's maximum halt velocity.
This fixes some rare "No next step" shutdowns on delta printers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allocate the stepper_kinematics directly in mcu.py - that way the
kinematic classes don't have to interact with the chelper code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move extruder.py, cartesian.py, corexy.py, and delta.py to a new
kinematics/ sub-directory. This is intended to make adding new
kinematics a little easier.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor