0343d0c73a
firmware_retract: Remove z_hop support
...
The current z_hop support did not work correctly with common slicers
that change Z height between retract and unretract, and it did not
work correctly with slicers that issue a retract at the end of a print
and then at the beginning of the next print.
The z_hop support is therefore being removed until these issues can be
fixed.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-10 19:25:56 -04:00
364c22fe84
probe: Rework the PROBE_ACCURACY command parameters
...
Don't default to a Z location of 10, as that could cause damage if the
probe's z_offset is greater than 10. Instead, use the "retract
distance" method that is used for normal multi-sample probing.
Update the PROBE_ACCURACY command parameter names to use the same
parameter names as the PROBE command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-10 15:21:09 -04:00
d4d8bf795b
filament_switch_sensor: add SET_FILAMENT_SENSOR gcode
...
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-07-10 09:57:46 -04:00
ea6f30bd99
docs: Update Protocol.md to use enumerations for pins
...
Now that pins use enumerations, update the set_digital_out command
examples.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-09 14:17:28 -04:00
e7dd313a96
docs: Add information on using OpenOCD to Bootloaders.md
...
Add information on using OpenOCD. Add information on flashing the
SAMD21 and SAMD51 with OpenOCD.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-09 13:37:17 -04:00
e19a41d0dd
docs: Add documentation for [delayed_gcode]
...
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-07-01 11:09:30 -04:00
57eb0e8975
docs: Update for latest changs to skew_correction
...
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-06-29 10:58:46 -04:00
3a3dfd51b9
docs: Add CLEAR_PAUSE to G-Codes.md
...
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-06-28 12:44:49 -04:00
d9d94c858a
docs: Add skew_correction.md to Overview.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-27 09:50:17 -04:00
a3b4543c97
skew_correction: add documentation
...
Signed-Off-By: Eric Callahan <arksine.code@gmail.com>
2019-06-26 20:16:35 -04:00
d9bddc35a1
docs: Add information on running the regression suite locally
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-23 17:59:23 -04:00
a2c7fd369c
docs: Note tmc2209 and tmc5160 support in Features.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-23 12:28:39 -04:00
ba27e0aa02
docs: Warn against using "PreloadVE" on KISSlicer
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-23 12:18:24 -04:00
83e6c01ada
probe: Allow probe parameters to be specified as g-code parameters
...
Add PROBE_SPEED, SAMPLES, SAMPLE_RETRACT_DIST, SAMPLES_TOLERANCE,
SAMPLES_TOLERANCE_RETRIES, and SAMPLES_RESULT parameters to the PROBE
command (and to commands that indirectly invoke a probe).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-21 14:44:28 -04:00
8cce3cc8e7
graphstats: Add support for interactive graphs
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-19 21:12:26 -04:00
8b00580884
gcode_macro: Parse variable_X parameters using ast.literal_eval()
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-07 19:33:31 -04:00
a541c2f60e
docs: Update Config_Changes.md with "samples" move to probe config section
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-06 10:15:47 -04:00
97adca18c4
docs: Update Delta_Calibrate.md with probe location bias info
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-06 10:08:58 -04:00
e061029b3a
docs: Update Probe_Calibrate.md with information on common probe errors
...
Add a section describing PROBE_ACCURACY, describing probe location
bias, and describing probe temperature bias.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-06 10:08:58 -04:00
5989f7a8a6
firmware_retraction: Implementation of tuneable G10/G11 firmware retraction ( #1617 )
...
This supports getting and setting of retraction parameters without
having to restart klippy.
Signed-off-by: Len Trigg <lenbok@gmail.com>
2019-06-06 09:10:09 -04:00
3f96c0abd8
docs: Minor wording change to Command_Templates.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-04 10:39:43 -04:00
962c48ecf7
docs: Fix github pages "liquid" rendering of Command_Templates.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-04 10:31:03 -04:00
94c1ad7241
docs: Add an initial Command_Templates.md document
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-04 09:50:30 -04:00
a68f577adf
gcode_macro: Add support for SET_GCODE_VARIABLE command
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-04 09:50:30 -04:00
ac8f6dfe20
gcode_macro: Rename "status" helper to "printer"
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-04 09:50:30 -04:00
a238ec6f98
idle_timeout: Add SET_IDLE_TIMEOUT gcode
...
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-06-04 09:46:26 -04:00
c54b8da530
gcode: Add support for SAVE_GCODE_STATE and RESTORE_GCODE_STATE commands
...
Add commands to save and restore the current g-code state.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-31 10:23:56 -04:00
d6b69938ab
gcode: Don't apply the SET_GCODE_OFFSET to the next g-code command
...
The SET_GCODE_OFFSET command could cause unwanted behavior when an
offset is applied to the following g-code command. (In particular,
when the following command is an extrude only move - as in
issue #1289.)
Don't apply the offset immediately. Instead, add support for a MOVE=1
parameter which will schedule a move to apply the given offset.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-26 11:19:15 -04:00
500f37821d
docs: Improve bltouch v3 documentation
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-26 11:09:32 -04:00
c77285287b
docs: Try to be more clear that the "paper test" steps need to be run
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-24 22:44:00 -04:00
6c4c26c319
docs: Minor wording change to Bed_Level.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-23 19:31:44 -04:00
1856f95503
docs: Recommend OctoPrint 1.3.11 or later
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-20 23:01:04 -04:00
ad12ffa981
docs: Use markdown syntax for http links in Bootloaders.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-20 17:19:33 -04:00
fd1dff3f02
docs: Fix numbering in FAQ
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-08 16:48:14 -04:00
73fd292637
docs: Update "avr restart=command" FAQ to point to bootloaders.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-07 23:02:20 -04:00
8524602b6e
docs: Fix inclusion of CONTRIBUTING.md in the automatic html generation
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-18 23:10:32 -04:00
17dd6e5097
docs: Fix markdown table layout in html rendering
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-18 22:56:56 -04:00
b5f79d5e77
docs: Simplify main html page now that there is a logo
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-18 22:37:56 -04:00
57cf0759c0
docs: Add logos to web page
...
Also, move docs/index.md to docs/_layouts/home.html. Add a
docs/_layouts/README file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-18 22:35:35 -04:00
85c01d4b6a
docs: Minor node changes to klipper logo
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-18 11:42:40 -04:00
49b18a6be7
docs: Update logo so that edges overlap
...
Overlapping edges reduce the effects of anti-aliasing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-18 11:31:29 -04:00
9b960e63fb
docs: Add a Klipper logo
...
Signed-off-by: Jonne Kuusela <johnedwa@gmail.com>
Signed-off-by: Michael J Shephard <michael.j.shephard@gmail.com>
Signed-off-by: Thomas Herrmann <therrmann23@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-18 11:31:29 -04:00
6f34ba59cb
docs: Add an index page for the www.klipper3d.org website
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-16 22:00:35 -04:00
4739e28137
docs: Add a github pages html template
...
Add an html template so that each page has a navbar at the top and a
sidebar on the left with an auto-generated table of contents.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-16 20:55:41 -04:00
64e7235e48
docs: Rewrite the Overview.md - just list documents by category
...
Replace the Overview.md document description with a list of documents
and a brief description of their contents. The goal is to make it
easier for users to find information.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-16 20:45:00 -04:00
cb04e4c45d
docs: Fix alignment of tmc2208.svg
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-16 11:34:45 -04:00
c440c6b7aa
docs: Start of google pages _config.yml file
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-15 11:04:23 -04:00
e3df39245f
docs: Fixup github pages
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-14 22:41:23 -04:00
8a6d415745
Update CNAME
2019-04-14 21:25:54 -04:00
b90a04a5cf
Create CNAME
2019-04-14 21:21:14 -04:00
Kevin O'Connor