Support reading a "gcode_id" parameter from heater/sensor config
sections.
Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Instead of directly turning off motors, heaters, and fans from
gcode.py, raise a new event and allow the heater, fan, and toolhead to
handle the event as needed.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit cf6c5e6f did not fix the shared heater case - a set_temp()
request takes the extruder id, not the heater id (nor the gcode sensor
id).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The gcode.py code should not peek into the heater classes to obtain
the gcode_id. Instead, introduce a new get_gcode_sensors() so that
the gcode.py code does not need to.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
When setting a temperature, lookup the heater via
self.heaters.lookup_heater() and do not use the gcode ids. This fixes
temperature setting when multiple extruders share the same heater.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The 'bed_shape' option has been removed. The user will enter a 'bed_radius' if they have a round be, otherwise they should enter 'min_point' and 'max_point'. When the bed is round the user should supply a 'round_probe_count' option, otherwise just 'probe_count'.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Most samd boards have the crystal and it does improve the clock
accuracy, so default to enabling it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for using the internal clocks (with USB clock recovery
mode if available) on the SAMD21. Don't use the internal clock if the
external crystal is requested (instead use the PLL synced to the
external 32Khz signal).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for USB clock recovery mode if an external 32Khz crystal
is not in use. If using an external crystal, then don't use the
internal 48Mhz DFLL48Mhz clock (just use the PLLs synced to the
external 32Khz signal).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The SAMD51 ADC is only clocked on rising edges (vs both rising and
falling edges on the SAMD21) and it has a greater minimum frequency
than the SAMD21. So, increase the ADC clock.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the field helper to simplify the bit manipulation in the driver.
This also enables the extended DUMP_TMC output.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Raise a printer.config_error() on an invalid register_command() call.
This error is easier to handle for the vast majority of callers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Implementation of "PROBE_ACCURACY" to measure the maximum, minimum,
average and standard deviation of a probe.
Signed-off-by: Rui Caridade <rui.mcbc@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The cpu is almost always 16Mhz and the serial port is almost always
UART0, so no need to prompt in the normal case.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the internal DWT timer is used for software timers, there is
no need to clock the peripherals at a higher clock speed. Clock all
peripherals at 48Mhz and simplify the clock generation code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor