The relax option corrupts the compilation on at least some versions of
gcc/binutils (eg, on fedora's avr-gcc 6.2.0 / binutils 2.27) due to
corruption of switch tables that use jump offsets. This issue is also
the root cause that resulted in commit d67f962a. Since the --relax
option provides minimal size / performance improvements it can simply
be dropped.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the reactor isn't running then implement pause using the system
sleep command. This simplifies the users of pause().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commmit a1c61563 renamed timer_shutdown() to timer_reset() but
neglected to delete timer_shutdown().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit 16e3dbb1 changed the avr implementation of timer_read_time().
Unfortunately, it raised the possibility for timer_read_time() to be
out of sync with the scheduler's understanding of the current time.
In particular, it was common for the timer irq to overflow the 16bit
hardware counter once at startup, and this would lead to
timer_read_time() always returning a time ~4ms ahead of the scheduler
on 16Mhz chips. This resulted in "Move queue empty" errors.
To resolve this issue, only increment timer_high from timer_periodic()
and make sure the timer irqs start immediately after timer_init().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Increase the default motor_off_time from 1 minute to 10 minutes. The
small value is a common source of confusion.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change the example files for cartesian printers to have a 25mm/s
maximum Z velocity. It's common to use lead screws for the Z axis on
cartesians and it is unlikely one would want to drive them at 250mm/s.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The code alignment of the TC0_Handler function seems to noticeably
impact performance benchmarks. Set the function alignment to 16 bytes
to improve testing consistency. An alignment of 16 doesn't
necessarily improve performance, but it seems to improve testing
consistency on code changes unrelated to timer dispatch.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename the file to make it clear that the code is helper functions for
boards with irq based timers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename sched_timer_kick() to sched_timer_dispatch() and move its loop
into its callers in the board code. This eliminates the need to
export timer_try_set_next() from the board code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Reset the timer repeat checks on shutdown, otherwise it is possible to
get into an infinite shutdown loop.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
On faster MCUs where a delay is needed between step and unstep use a
"busy loop" in the scheduler instead of trying to schedule to the
unstep time. This reduces the chance of jitter in the scheduler
accumulating.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Directly use the Kconfig defined CONFIG_CLOCK_FREQ in the code and
avoid defining F_CPU. Also, remove the unnecessary O2 option - that
is already the default from the main makefile.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some additional tweeks to the scheduler has resulted in minor
improvements to the stepper benchmarks.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Explicilty load the timer waketime variable into local variables in
sched_timer_kick(). Change the optimization level from Os to O2.
This helps gcc to avoid unnecessary reloads from memory in the common
stepper_event() case.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Provide hand-coded assembler for timer_is_before() on AVR as that code
is used frequently in the time-critical timer dispatch loop and gcc
doesn't do a good job at compiling that comparison code. Remove the
no longer needed waketime+1 hack from reschedule_timer().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move sched_is_before() from sched.c to timer_is_before() in the board
specific timer code. This allows the board code to provide its own
definition.
Also, remove the sched_from_us() and sched_read_time() wrapper
functions and change the callers to directly invoke timer_from_us() /
timer_read_time().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit f28eb902 reworked the switch to fix int16 encoding. However,
at least one version of avr gcc doesn't like that switch layout (it
uses a jump table). Reorg the switch to avoid that issue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The est_clock calculation code requires timestamps on status messages
to never be prior to the reception of the message. The eventtime of
handle_message() is taken before the read() and there is a small
possibility that it could be inaccurate enough to corrupt the
est_clock calculation. Take a new timestamp when storing receive_time
to prevent this. This fix prevents some firmware "Move queue empty"
shutdowns.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The code wasn't properly sign-extending 16bit integers which caused
int16_t reports in output() to appear as uint16_t.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support timing the simulation scaled to the system clock. This can be
used to make the host estimation of the mcu clock more accurate.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't start/stop the simulavr simulation loop to do IO - instead
implement the IO directly in the serial callback handlers. This
improves the speed and consistency of the simulation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
sqrt() of a negative number in the C code returns NaN. This value
results in behavior that is difficult to debug. Always return 0.0
instead as this results in better behavior that is easier to track
down. Also, on some code paths, safe_sqrt is called on numbers that
are multiplied by very large amounts (eg, 16000000**2) and thus
distinguishing between large and small negative numbers is difficult.
For now, report in the log if the value is below -0.001.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The code disables lookahead between two extruding moves with
significantly different extrude ratios. Unfortunately, it was
possible for very tiny moves to show different extrude ratios just due
to how the slicer implements rounding when it produces the gcode.
Allow lookahead to be enabled between moves with extrude ratios that
are different if they don't noticeably produce more or less extrusion.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Be less likely to raise a "Move exceeds maximum extrusion cross
section" error on very short moves. It's okay to extrude a little
extra plastic on moves shorter than the nozzle diameter.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Catch and ignore any exceptions when trying to shutdown the printer in
toolhead.force_shutdown() - there's a good chance an exception will be
raised as this method is often called after an invalid internal state
is found.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The previous calculation was only valid if the stepper is always
commanded to a position that is an exact multiple of the
step_distance. The safety check was programmed with a value too large
for other commanded positions, which could result in "No next step"
errors. Fix by changing the calculation to use the worst case
scenario.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't force a firmware shutdown on a simple gcode parse error.
Instead, report the error back to the user and otherwise ignore the
command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Fix a corner case where a residual in the PID could cause a non-zero
pwm request even when the target_temp is zero. (Which could lead to a
firmware "Missed scheduling of next pwm event" shutdown.)
Simplify the logic for suppressing duplicate pwm updates and make sure
a zero target_temp always results in a zero pwm update on the
following set_pwm calculation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor