Updates for generic-bigtreetech-skr-2.cfg to include comment on newly shipped board with STM32F429 instead of the original STM32F407
Signed-off-by: James Hartley <james@hartleyns.com>
It seems the common "beta 3950" thermistors generally follow a
temperature table defined by the new "Generic 3950" definition. Using
a table that actually follows the "beta 3950" temperature curve is
generally less accurate. Deprecate the existing "NTC 100K beta 3950"
definition to avoid this common issue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Example default config for Tronxy XY-2 Pro.
It is default config for printer Tronxy XY-2 Pro (mainboard Chitu V6). This config based on config for Tronxy X5SA with mainboard Chitu V6.
Signed-off-by: Konstantin Bazhenin <kby@list.ru>
This commit contains a configuration for the Anycubic Vyper printer from 2021.
It uses a clone of the STM32F103 chip named GD32F103.
There are 2 Mainboard versions out there v0.0.5 and v0.0.6, this config has
been tested with the v0.0.6 only. It should probably work for v0.0.5 as well
since there are no different changes in the Anycubic Marlin firmware.
The LCD is not supported yet (might work, but didn't try yet).
Signed-off-by: Marc Neuhaus <marc@neuhaus.nrw>
Signed-off-by: Manuel Fichtner <manuel.fichtner@me.com>
Fixing initial rotation distance on Thinker S stocker extruder
Removing author information
Fixing Z Axis homing speed as it was too fast.
Signed-off-by: Demetrius Apostolopoulos <dapostol73@hotmail.com>
This config I created and fully tested on my own printer Anycubic 4Max Pro 2.0. This works fine! Please note that this printer is different from the Anycubic 4MAX.
Signed-off-by: Alexander Usachev <int_0x21@protonmail.com>
This is just a short inline comment about Bigtreetech's implementation of the "anti-reversal stepper protection" and the way it should be handled in the Klipper printer configuration.
Signed-off-by: Jerry Chapman <truckershitch@hambone.e4ward.com>
The atmega328pb has officially named these pins as PE2 and PE3, so use
that naming scheme instead of the previous Klipper invented names.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The M300 example macro now sets the PWM cycle time to generate the requested
frequency. 'scale' did not have the desired effect. Duty cycle is now
fixed at 0.5. All S parameter values less than 1 generate a 1Hz 'tone'
to avoid division-by-zero.
Signed-off-by: Stefan Holst <mail@s-holst.de>
This config was a community effort and was author and tested by sihawken, 3D.Subzwari & dapostol73.
Signed-off-by: Demetrius Apostolopoulos <dapostol73@hotmail.com>
Information and some lines verbatim were sourced from the official BigTreeTech Octopus
GitHub repository to make this configuration as well as existing configurations in the same
folder as this one
Signed-off-by: Charles Pickering <charles.pickering@live.com>
Add a pin definition to enable motor power and add a warning about
initial faulty SKR2 boards.
Reported by @FHeilmann.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Adds Duet3 Mini Config with support for expansion header
Signed-off-by: Luke Ashley <Luke@Lukeslab.online>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
To support continuous belt printing, add nestable repeat
loop support via an `[sdcard_loop]` module.
Supported G-Code:
- SDCARD_LOOP_BEGIN COUNT=n ; Loop for N times, or infinitely if N is 0
- SDCARD_LOOP_END ; End of loop
- SDCARD_LOOP_DESIST ; Complete all loops without iterating
Marlin M808 compatibility example in `config/sample-macros.cfg`:
- M808 Ln ; Loop for N times, or infinitely if N is 0
- M808 ; End of loop
- M808 K ; Complete all loops without iterating
Added unit tests in test/klippy/sdcard_loop.test
See https://reprap.org/wiki/G-code#M808:_Set_or_Goto_Repeat_Marker
Signed-off-by: Jason S. McMullan <jason.mcmullan@gmail.com>
Change all the example config files to use either 0 or 999999 for
stealthchop_threshold (as is recommended in the TMC_Drivers.md
document).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for the Creality CR-30 'PrintMill', and its base board,
the Creality v4.2.10.
Add them to the `test/klippy/printers.test` test suite
Signed-off-by: Jason S. McMullan <jason.mcmullan@gmail.com>
A working configuration example for Tronxy X5SA Pro printer (https://tronxy.com/x5s-series/x5sa-pro.html) with no Touchscreen funcionalities because separated LCD firmware needed.
Silent TMC2225 drivers soldered on board.
The Self-levelling plate sensor is a blue Tronxy XY-08N model.
Direct Drive is a Titan Extruder Clone "3:1" gear ratio.
Signed-off-by: Morgan Barresi <morganfw@gmail.com>
Improvements and fixes based on feedback:
* Make speeds and limits more conservative
* Fix Y endstop position
* Improve IR bed leveling
* Fix filament runout pin
Signed-off-by: Justin Schuh <code@justinschuh.com>
Create a sample-aliases.cfg with all the aliases that are currently
hardcoded in the klippy.pins.py module.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This adds support for BMP280 and BME680 sensor ICs,
along with fixing calibration data readout for BME280.
Gas sensor readout for the BME680 is just the raw compensated value.
To get actual meaningful values, more research is needed.
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
A working configuration example for Hiprecy Leo printer (https://www.hiprecy.com/product/402/) with no Touchscreen funcionalities because separated LCD firmware needed.
TMC2130 SPI drivers.
The Self-levelling plate sensor is PINDA probe type
Direct Drive is a BMG "3:1" gear ratio
Signed-off-by: Morgan Barresi <morganfw@gmail.com>
There are two fan pins on Robin Nano 3 and the fan1 pin is PC14, not PB1.
PB1 pin that was in config example is used for the fan2 output.
Signed-off-by: Oleksii Zelivianskyi <alexeyzel@gmail.com>
we just found a small problem: Some people have slightly higher endstop positions, which caused them to have a move out of range during probe calibrate.
Signed-off-by: Christoph Frei <fryakatkop@gmail.com>
Fixed bltouch offset and bed_mesh mesh_min/max to account for offset.
The former was defined in the wrong coordinate, as the origin starts from the SW. The latter did not include the offset and caused an error. Technically the offset allows mesh_max up to (239.3, 253).
Signed-off-by: Ben Kaye <benkaye001@gmail.com>
Add generic-bigtreetech-gtr.cfg to printers.test. Add definitions for
thermocouple and temperature_mcu.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Added Ender 3 Max config. Based off the configs from ender6, ender3-v2, and ender3. Also contains optional BLTouch parameters.
Signed-off-by: Chad Schwieterman <chad.devops@gmail.com>
The Lulzbot TAZ6 single extruder configuration had an XY position for
z homing that did not match the factory firmware, and was off center
enough to cause the extruder to crash into the home button trim
sometimes when homing. This commit changes the printer config so
that the XY position for Z homing matches the original Marlin firmware
for this printer.
The Lulzbot TAZ6 single extruder configuration had an bed_tilt points
that did not match the factory firmware, and were off enough that the
nozzle (used for probing on this printer) could slip off the edge of
the probe point or miss it entirely. This commit changes the printer
config so that the coordinates for bed_tilt calibration match the
original Marlin firmware for this printer.
For the Lulzbot TAZ6 single extruder config, use 'gear_ratio' and
'rotation_distance' to configure the extruder.
The rotation distance is based on effective circumference of the hobbed
bolt based on the original Marlin firmware for the TAZ6 single-extruder,
and the gear ratio was determined by simply counting the number of
teeth on the pinion and spur gears.
Signed-off-by: Steven T. Snyder <github@steventsnyder.com>
Add support for automatically calculating the internal step_distance
from new config parameters - rotation_distance, microsteps,
full_steps_per_rotation, and gear_ratio.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Minor indentation changes and remove default values for heater_fan.
Add to printers.test test cases.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Adds config for the Monoprice Select Mini v2 cartesian printer. I have
successfully tested the configuration.
Signed-off-by: Kilian Neuner <github@9-r.net>
Add an 'mcu' option to the board_pins config and use that to specify
the name of the mcu to apply the aliases to. Support applying the
aliases to multiple mcus.
Add support for any number of options starting with an "aliases_"
prefix.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move all the config reference information from files in the config/
directory to a new Config_Reference.md document.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Config should not specify a default pressure_advance. Note limit on
current with old 30 Ohm Z-motor.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Fixing alias for thermistors to be on the host rather than the PRU.
Moving the D1W alias from PRU MCU to host MCU.
Signed-off by Jon Charnas <goeland86@gmail.com>
Corrected the diag1_pin numbers. Useful for anyone copying and pasting the lines. Its something really easy to look over and can lead to some hair pulling from the time wasted trying to troubleshoot why the tmc diag pin error from Klipper.
Signed-off-by: Juan Moreno <uncholowapo@gmail.com>
JamesH1978