Add get_status wrapper with last_query status for macros It is sometimes useful to determine the state of the probe from a macro. If the probe is connected to an endstop pin, the results can be obtained via QUERY_ENDSTOPS but if a physical endstop is in use in addition to the probe the probe state cannot be obtained. This change allows one to use QUERY_PROBE and then access the printer.probe.last_query object to obtain the state.
Signed-off-by: Paul McGowan <mental405@gmail.com>
Update callers to use the printer.command_error reference instead of
directly using homing.CommandError() when raising or catching errors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
There's no reason to distinguish between an EndstopError and a
CommandError, so just use CommandError.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Increase the maximum redraw rate from 4 times per second to 10 times
per second. Some users have reported slower rendering times as a
result of 8fa1c977.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Split up the main GCodeParser class into GCodeDispatch and GCodeMove
classes. The GCodeMove class is now available using the "gcode_move"
printer object name. This split simplifies the gcode.py code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename printer.gcode.action_emergency_stop() to
action_emergency_stop(), printer.gcode.action_respond_info() to
action_respond_info(), and printer.gcode.action_respond_error() to
action_raise_error() in command templates.
This simplifies the get_status() interface, as returning callable
functions from that interface was confusing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a helper function for submitting relative movements. This
function will also automatically ensure gcode.reset_last_position() is
called.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Generate a "toolhead:set_position" event on a call to
toolhead.set_position() and use that event to automatically call
gcode.reset_last_position().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a request_redraw() method and call it when a key menu event
occurs. Limit these proactive screen redraws to no more than 4 per
second.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
After reading the first item of self.filament_array, filament_width is updated back to self.nominal_filament_dia or self.diameter instead of retaining the value until next pending_position.
Updated Filament Menu Template.
Signed-off-by: Nicola Falciani <nicola.fal@gmail.com>
- don't populate all items at once
- populate items when container is pushed to stack
- precreate List back item, don't create it during populate.
- don't update items during populate
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
Use the "info" webhook to pass critical process information back to
the caller. The remaining users of register_static_path() can get the
required information via get_status() calls.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
In case of an overwriting existing menu item,
the new item was added additionally to the end of the items list.
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
menu.cfg:
- jinja2 template scripting
- new Setup menu
- new Calibration menu
menu:
- redesigned menu code
- jinja2 support
- option to reverse menu up and down directions
- functionality set to support menu injection from other modules
- a new way of defining menu hierarchy
- other adjustments
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
Arc travel was working but extrusion in absolute mode seemed not to be happening at all. This was because the E coord being sent with each G1 segment of the arc was not incrementing, effectively the same value was being sent over and over so the total extrusion for the whole arc was the amount for just one segment which is an extremely tiny amount.
My change increments e_base by e_per_move for each subsequent coord when in absolute extrude mode which results in the correct absolute E value being sent for each segment.
Signed-off-by: Toby Harper <toby@fuith.org>
Arksine