- Changed max positions
- Tuned PIDs for my stock Ender 3 heaters (using 200/50)
- Added the serial device as 'by-id'. Not sure if that is working as I
expect it :)
- I did set the position endstop to 0.5 .. Not sure if people like that.
Signed-off-by: Hans Raaf <hr-klipper@oderwat.de>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The recommended TOFF time in "standalone mode" according to the
tmc2130 is 4, so use that as the default.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The extrude_factor and extruder position are specific to the current
extruder, so reset them to default values on a Tn command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the new gcode.register_mux_command() so that SET_PRESSURE_ADVANCE
works correctly with multiple extruders.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's common to add commands that dispatch to a particular object
instance depending on the value of a command parameter. (For example,
the command "SET_SERVO SERVO=xyz" wants to be handled by the
particular "xyz" servo instance.) Add a register_mux_command() helper
to gcode.py make it easier to do this.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the common config reading and probe object lookup from the
bed_tilt.py and delta_calibrate.py code into the ProbePointsHelper
class.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Raise an error during config parsing if the position_endstop is not
between the position_min and position_max. This avoids a confusing
error message during homing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The cr10 mini is the same as the cr10, but with different Y and Z
dimensions. Reported by @cassianoleal.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
For some reason, Linux creates the pseudo tty with group writable
permissions, but not group readable. Use chmod to allow the device to
also be group readable.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The gpio_out_toggle() function in the sam3x8e and stm32f1 code was
only valid if it was called with irqs disabled.
Commits 018c5daa and 9c52ad43 enabled the lcd code which called
gpio_out_toggle() with irqs enabled. This could cause corruption of
the gpio state.
Introduce a gpio_out_toggle_noirq() function that will only be invoked
with irqs disabled, and fix gpio_out_toggle() on sam3x8e and stm32f1
so that it safe to call even if irqs are enabled.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The step speed rounding and the cpu delay must be run after running
the endstop specific preparation code. Otherwise, a delay in the
home_prepare() code could undo those calculations. Specifically, this
could lead to errors on a multi-mcu setup when the Z is homed using a
virtual_z_offset and there is a delay in the activate_gcode section.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't return early on a command error - continue to process remaining
commands and pop commands from the queue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the generic spi send/receive code on Linux. Update the replicape
code to use the updated command format.
Also, update the replicape code to turn off the stepper motors on a
shutdown event.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Improve the SPI message transmit system. Add support for bus speed
and bus mode. Add support for sending SPI messages on shutdown.
Signed-off-by: Petri Honkala <cruwaller@gmail.com>
Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
In order to properly delay BACKGROUND_PRIORITY_CLOCK messages, they
must be 5ms beyond the minimum defined by MIN_REQTIME_DELTA. So, add
both MIN_REQTIME_DELTA and MIN_BACKGROUND_DELTA to the timing of these
messages.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the clock querying messages occur at a similar frequency to other
events on the micro-controller or host, then it's possible for the
load created by those other events to skew the clock synchronization.
In particular, the 500ms lcd screen update could resonate with the 1
second clock query. Use an unusual clock querying frequency to avoid
this issue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor