Marlin examples use the "ATC Semitec 104GT-2" thermistor for the CR10,
CR10S, and CR10mini. Reported by @dovcharov.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
- When using absolute extrusion the gcode position e-axis position is now captured on PAUSE and restored in RESUME with a call to the G92 handler.
- Add a get_status() function that returns a dictionary with an 'is_paused' key.
- Do not allow consective calls to PAUSE or RESUME to exectue. Also do not allow a RESUME to executed without a previous PAUSE.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
The sram matrix configuration is, bizarrely, configured with a slow
default. It will typically add an extra wait state to every memory
access. Set the matrix sram controller to improve the performance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Avoid using the "low-level" library timing utilities. This is in
preparation for using SysTick as part of the timer implementation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The ARM CortexM3 (and later) chips almost always have a 32bit timer in
the "Debug and Watch Trace" (DWT) unit which resides within the cpu
core itself. This timer is generally faster to access than timers
located on the chip's peripheral bus. When combined with the standard
ARM SysTick timer it provides a (generally) portable mechanism to
implement Klipper's software timer mechanism. It's generally also
faster than using the vendor specific timers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit f4d323ad changed the handling of the self.speed variable, and
it inadvertently changed the default startup speed. Return to the
default of 25mm/s.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
In the normal case, a regular pin_up command should be sufficient to
raise the probe. (Should the regular pin_up fail, the code can issue
a "reset" command during the retry.)
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit c3efcd9c moved the config_spi setup to a build_config callback.
It's also necessary to move the config_thermocouple to a build_config
callback as well.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add helper function for reading current, microsteps, and stealthchop
settings from the config file. Use these helpers in both the tmc2130
and tmc2208 modules.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move these helper functions to the FieldHelper class so that they can
be used by other Trinamic drivers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Report values of TMC2208 register fields in DUMP_TMC command to help in
tuning and diagnostics.
This also adds functions to refer to register fields by name for TMC drivers
and register mappings for TMC2208.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Signed-off-by: Dmitry Frolov <dmitry.frolov@gmail.com>
Stopping the connect sequence can make it difficult to get the bltouch
out of an error state. Allow the connect to proceed, ideally if the
bltouch stays in an error state it will be detected during the first
probe attempt.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
I noticed Octoprint was disconnecting after a while, and after reading the logs, I came across this error:
```
Unhandled exception during run
Traceback (most recent call last):
File "/home/pi/klipper/klippy/klippy.py", line 171, in run
self.reactor.run()
File "/home/pi/klipper/klippy/reactor.py", line 176, in run
g_next.switch()
File "/home/pi/klipper/klippy/reactor.py", line 203, in _dispatch_loop
timeout = self._check_timers(eventtime)
File "/home/pi/klipper/klippy/reactor.py", line 82, in _check_timers
t.waketime = t.callback(eventtime)
File "/home/pi/klipper/klippy/extras/idle_timeout.py", line 62, in timeout_handler
return self.check_idle_timeout(eventtime)
File "/home/pi/klipper/klippy/extras/idle_timeout.py", line 59, in check_idle_timeout
return self.transition_idle_state(eventtime)
File "/home/pi/klipper/klippy/extras/idle_timeout.py", line 35, in transition_idle_state
logging.exception("idle timeout gcode execution")
NameError: global name 'logging' is not defined
```
I therefore added the missing import.
Signed-off-by: Samori Gorse <samori.gorse+github@gmail.com>
Add updates to example-extras.cfg and G-Codes.md documenting pause_resume. Also add M600 (filament change) to sample-macros.cfg.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
This module adds PAUSE and RESUME gcodes that can programatically determine if the gcode is printing from virtual sd or over the serial connection. It also captures the current toolhead position and gcode feedrate on pause, and recovers that position and feedrate on resume.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
- Add is_active() member function to return the active printing status of the virtual sdcard
- M27 now reports current file position when file has been opened. See http://marlinfw.org/docs/gcode/M027.html
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Kevin O'Connor