Use new mcu.lookup_query_command() for all commands that query
information from the micro-controller.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Convert standard queries to use the acknowledgments of the sent
command to determine if the response was received or not. This also
controls command retransmissions (should the response have been lost).
The tmc_uart.py will continue to use the old mechanism as the tmcuart
responses are not sent synchronously with the query command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add ability for the host code to get a notification when the ack for a
command sent to the micro-controller is received. This is in
preparation for improved detection of message loss between mcu and
host.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the serial command wrapper class from serialhdl.py to mcu.py.
This will allow that class to better support higher level
functionality.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Introduce a main send_with_response() helper function and use it
during identify and the setup of clocksync.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Reduce the delay in send_with_response() by introducing a reactor
mutex to wake the main thread when the response is obtained.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the mcu is using a traditional serial port, then only send a new
message block if there is space available in the mcu receive buffer.
This should make it significantly less likely that high load on the
mcu will result in retransmits.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Automatically clear the information printed at the start of each log
file rollover on a klippy internal restart.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a lookup_command() method to the SerialReader class that provides
a wrapper that stores the serial and commandqueue references. This
makes it easier to run the send() method.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Store the gcc and binutils versions used in the compilation of the
firmware in the firmware data dictionary. Forward that information to
the log so it is available during debugging.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The logging module can build strings directly from printf syntax - no
need to build the string first.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Build a single (very large) logging message with the debug state.
This prevents the output from being fragmented.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The existing clock synchronization code has two flaws: intermittent
transmission latency during get_status requests can cause the
estimated clock to be too low, and the estimated clock calculation did
not take into account possible clock drift between samples. The
former could potentially lead to "Timer too close" errors and the
latter could potentially lead to "Move queue empty" errors.
Rework the code to avoid the above problems. It's not necessary to
estimate the micro-controller clock as an excellent estimate is
reported by the micro-controller (via the CLOCK_FREQ constant).
Account for a small drift from the reported value, and check on each
sample if the drift exceeds the expected limits. With a good starting
estimated clock, only the offset needs to be calculated. Use previous
offsets (and the estimated clock) in calculation of new offsets to
avoid intermittent latency from badly skewing the results. Finally,
add an additional time offset of one millisecond to account for any
minor inaccuracies.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the reactor isn't running then implement pause using the system
sleep command. This simplifies the users of pause().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the logic to calculate and report the stepper's current position
from endstop.c to stepper.c. This localizes the stepper code into
stepper.c.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add initial support for micro-controller resets via the Arduino reset
mechanism. Also, automatically attempt a firmware restart if the
printer CRC does not match.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Store a full 64bit uptime in the mcu and query it at the start of each
connection. This ensures the host's 64bit clock is always in synch
with the mcu's clock.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The normal system clock can have sudden jumps if the system clock is
changed. Use the system monotonic clock to avoid these sudden changes
in time.
It appears the Raspbian OS (which is used by OctoPi) is setup to
update the system clock upon network connectivity. This could cause
sudden system clock changes which could lead to Klippy processing
errors. Using the monotonic clock eliminates these issues.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The serialqueue_flush_ready() code was used to flush queue_step
commands during a homing operation. It's no longer necessary now that
moves during a homing operation use the normal message priority
system.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Log the constants reported by the MCU and log the number of move items
allocated after configuration.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a DECL_CONSTANT macro to allow the firmware to define constants
that are to be exported to the host during the "identify" phase. This
replaces the existing hardcoded mechanism of scanning the Kconfig
header file for certain constants.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The arduino style serial port interfaces can reset the MCU when the
serial port is opened. Clearing the HUPCL flag makes this less
likely.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor