Commit Graph

134 Commits

Author SHA1 Message Date
Douglas Hammond c105adc80b temperature_fan: Fix. Temperature fan min speed should be used (#1405)
Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
2019-03-28 14:07:40 -04:00
Kevin O'Connor 9aadc3c7fa docs: Also note that driver_VSENSE was removed from tmc2660 driver
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-22 22:40:42 -04:00
Kevin O'Connor 871e028c27 config: Document the [include] directive
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-22 20:48:15 -04:00
Kevin O'Connor 3945905420 config: Minor rearrangement of example-extras.cfg
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-22 20:46:37 -04:00
Kevin O'Connor efab177645 docs: Note tmc2660 driver_HEND default change from 6 to 3
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-22 20:41:32 -04:00
Matt Baker f2fbe98454 bed_mesh: enable relative offset bed meshes (#1323)
Adds parameter for bed meshes to be adjusted relative to a probed point
during calibration. This allows the probe z offset to be ignored for
probes that are not stable over time (for example, the thermal drift of
inductive probes). An endstop other than the probe is then necessary to
determine the bed-nozzle offset.

Signed-off-by: Matt Baker <baker.matt.j@gmail.com>
2019-03-21 10:39:22 -04:00
Kevin O'Connor d3f6dad853 controller_fan: Allow multiple controller_fan sections to be defined
It may be necessary to define multiple fans, so allow each config
section to be named.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-10 13:57:01 -04:00
Kevin O'Connor 19c7955f2a config: Improve the description of z_tilt z_positions
Reported by @sensille.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-10 12:24:34 -04:00
Rui Caridade 5c0a2479be screws_tilt_adjust: Add new screws_tilt_adjust tool (#1367)
Signed-off-by: Rui Caridade <rui.mcbc@gmail.com>
2019-03-08 11:47:17 -05:00
Kevin O'Connor fcaa75f014 config: Update default spi speed in tmc2660 description
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-08 11:27:50 -05:00
Kevin O'Connor 563bc37073 tmc2130: Rename driver_BLANK_TIME_SELECT to driver_TBL
Use the field names from the trinamic specification.  This makes the
field similar to all the other driver_XXX config options.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-08 11:25:19 -05:00
Florian Heilmann e96b71a9a3 tmc2660: Use helper functions for register access and simplify TMC2660 parameters
sense_resistor is now a mandatory parameter for tmc2660 blocks. Duet2 users should use a value of 0.051

Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2019-03-08 11:04:14 -05:00
Florian Heilmann 4541f16cd9 tmc2660: Add vsense_resistor config parameter
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2019-03-08 11:04:14 -05:00
Kevin O'Connor 47d51d8613 config: Update verify_heater description
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-08 10:55:46 -05:00
Kevin O'Connor d62a41b930 manual_stepper: Add support for moves with acceleration
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-03 13:38:10 -05:00
Arksine 69491e2dab filament_switch_sensor: update documentation
Signed-off-by:  Eric Callahan <arksine.code@gmail.com>
2019-03-01 00:45:51 -05:00
Kevin O'Connor c8d7e28a35 atsamd: Add support for programming SERCOM pins
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-01 00:40:44 -05:00
Douglas Hammond b6589406d4 temperature_sensor: Add generic temperature sensor support
Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-26 13:15:56 -05:00
Douglas Hammond 3887ad4fce heater: Support generic gcode_id registration for sensors
Support reading a "gcode_id" parameter from heater/sensor config
sections.

Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-26 12:07:00 -05:00
Arksine f7d8854587 bed_mesh: simplify configuration
The 'bed_shape' option has been removed.  The user will enter a 'bed_radius' if they have a round be, otherwise they should enter 'min_point' and 'max_point'.  When the bed is round the user should supply a 'round_probe_count' option, otherwise just 'probe_count'.

Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-02-25 13:34:14 -05:00
Kevin O'Connor 80c8bd8b4d bed_screws: Add a helper tool for leveling bed screws
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-24 00:49:47 -05:00
Kevin O'Connor 834b9e3d92 config: Warn that cycle_time may not match when using hardware_pwm
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-19 13:19:32 -05:00
Kevin O'Connor cc4ecef88b mcp4018: Add initial support for the mcp4018 digipot
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-16 08:16:37 -05:00
nopbit 0f674ef407 tsl1401cl_filament_width_sensor: Filament Width Sensor Support (#1132)
Support added for filament diameter sensor. Sample configuration parameters added to example-extras.cfg.

Signed-off-by: Mustafa YILDIZ <mydiz@hotmail.com>
2019-02-14 10:13:48 -05:00
KevinOConnor c6d1d1bd8c
Merge pull request #1242 from john--/pr_generic_heater
Generic Heater Support
2019-02-14 10:08:26 -05:00
John Jardine 6316b2c1b6 Generic Heater Support
Adds the ability to register a custom/generic heater through a new extra called heater_generic.
This takes a gcode_id that is reported by M105. Adds a new command to set the temperature for any heater using the syntax:
SET_HEATER_TEMPERATURE HEATER=<heater_name> TARGET=<target_temp>

Signed-off-by: John Jardine <john@gprime.net>
2019-02-14 01:15:11 +00:00
Kevin O'Connor 98ed462865 spi_software: Implementation of software spi
Signed-off-by: Matt Janus <FragginRight@variabl.es>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-13 11:52:20 -05:00
Kevin O'Connor 2d7c3a84ee manual_stepper: Add an "extras" module for manually controlling a stepper
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-12 13:38:13 -05:00
Kevin O'Connor 345a5f4e1f bltouch: Increase default pin_move_time from 200ms to 675ms
Use the same pin move time that Marlin uses.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-04 18:02:53 -05:00
Arksine cdcc320710 bed_mesh: add support for round beds
Signed-off-by:  Eric Callahan <arksine.code@gmail.com>
2019-02-02 23:29:00 -05:00
Arksine 893cbbab83 pause_resume: update documentation
Add updates to example-extras.cfg and G-Codes.md documenting pause_resume.  Also add M600 (filament change) to sample-macros.cfg.

Signed-off-by:  Eric Callahan <arksine.code@gmail.com>
2019-01-28 11:23:52 -05:00
Kevin O'Connor 7327394c50 adc_temperature: Add support for linear interpolation of resistances
Add support for performing linear interpolation between a set of
measured temperature/resistance pairs.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-21 21:28:25 -05:00
Kevin O'Connor 8a97bc592b bltouch: Add a pin_up_touch_mode_reports_triggered config option
Rework the undocumented test_sensor_pin config option into a
pin_up_touch_mode_reports_triggered option and document it.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-21 09:52:11 -05:00
Kevin O'Connor e36122797b bltouch: Attempt to verify that the probe raises after each probe attempt
Query the bltouch state during the pin_up command to try and verify
that the probe does actually retract.  This may be useful to detect if
the bltouch enters into an "error" state.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-21 09:52:11 -05:00
Master92 a27838bc05 controller_fan: Add support for a fan cooling the controller-board (#1070)
Whenever a stepper driver or a heater becomes active, it is desirable to turn on a fan cooling the associated parts on the controller board. This module implements such a fan that turns on whenever a stepper or specified heater turns on, decelerates to a configurable speed when all of the watched parts turn off, and returns to an off-speed, when a user-defined timeout is met.

Signed-off-by: Nils Friedchen <Nils.Friedchen@googlemail.com>
2019-01-10 12:12:15 -05:00
Yannic Schröder d015209388 docs: Add guide for sensorless homing (#1004)
Signed-off-by: Yannic Schroeder <schroeder@ibr.cs.tu-bs.de>
2019-01-07 10:39:16 -05:00
Kevin O'Connor c2086796bf mcp4728: Add initial support for the mcp4728 i2c dac chip
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-02 18:17:56 -05:00
Alec B. Plumb 59e9b6562f respond: An extra for sending messages to the printer host. (#1053)
I have made one change to `gcode.py` to support quoted parameter
values.

I have added support for the basic `M118` command (see
https://reprap.org/wiki/G-code#M118:_Echo_message_on_host). I have
also added a `RESPOND` command that takes extended parameters.
`ECHO` might be a better name than `RESPOND` but is already defined
in `gcode.py`.

Signed-off-by: Alec B. Plumb <alec@etherwalker.com>
2019-01-02 17:45:35 -05:00
Kevin O'Connor 531575651c bltouch: Document that bltouch "clones" may not work correctly
There is concern that the bltouch.py module may not perform adequately
on some bltouch "clones".  Document that.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-12-18 17:12:44 -05:00
Kevin O'Connor ccc25a03d5 bltouch: Add a config option to disable the bltouch sensor test
It appears some bltouch "clones" do not report the probe as triggered
when put in "touch mode" while the pin is raised.  Add a config option
to allow users to disable the test.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-12-16 11:06:41 -05:00
Kevin O'Connor 44aa5def73 bltouch: Allow the pin_move_time to be configured
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-12-04 10:34:54 -05:00
Arksine 581b1439f3 config: Update bed_mesh in example-extras.cfg
Update documentation about the fade options. Also inform the user that it is recommended to home toward the center of the print area when using a probe for z homing.

Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2018-11-30 11:37:21 -05:00
Kevin O'Connor 824e55d75a bltouch: Add initial support for a bltouch "extras" module
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-30 11:34:20 -05:00
Kevin O'Connor 147d805231 mcp4451: Use bus.py helper code for i2c
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-24 00:33:22 -05:00
Kevin O'Connor e5150fe187 uc1701: Add support for SSD1306 in i2c mode
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-23 22:04:06 -05:00
Kevin O'Connor e231ac7422 uc1701: Add support for SSD1306 displays
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-21 20:45:53 -05:00
Kevin O'Connor 9ba94ded9e tmc2660: Use bus.py helper code for spi
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-21 12:12:31 -05:00
Jiri Dobry e541466591 servo: This patch create ability to enable/disable attached servo. (#880)
Cheap mechanical servos have small flickering. When this servo stay on one position, this flickering slowly destroy internal potentiometer and make servo unusable. Many mechanisms need servo only to change position. Therefore I create this minor path to enable/disable servo. It stop pulses for this servo, that's all.

Corresponding G-code is:
SET_SERVO SERVO=config_name [WIDTH=] [ENABLE=<0|1>]
SET_SERVO SERVO=config_name [ANGLE=] [ENABLE=<0|1>]

For example:
SET_SERVO SERVO=touch ANGLE=80 ENABLE=1 ; enable servo and set position
G4 P200 ; wait 200ms
SET_SERVO SERVO=touch ENABLE=0 ; disable servo

This patch add one option to servo configuration:
enable: <False/True> # default True

It not have impact to user code existing already because it is optional parameter and default value is same as original behavior.

Signed-off-by: Jiri Dobry <jdobry@centrum.cz>
2018-11-14 09:38:09 -05:00
Florian Heilmann 4372d1812c Implement idle event support in the TMC2660 extra
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2018-10-28 18:45:49 -04:00
Florian Heilmann f57c29442c Add SX1509 extra
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2018-10-27 10:34:28 -04:00