Add an optimized step function for drivers that support stepping on
both rising and falling edges of the step pin. Enable this
optimization on 32bit ARM micro-controllers. Automatically detect
this capability in the host code and enable on TMC drivers running in
SPI/UART mode.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The floating point unit must be enabled in order to use it and Klipper
does not currently implement that. Newer versions of gcc may spill
registers to the floating point unit causing failures.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a new build definition to note micro-controllers that have strict
timing. The Linux mcu code does not have strict timing - all other
targets currently do.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The main() function has a special meaning to gcc and using it can
result in different code generation. Use armcm_main() to avoid that.
Also, invoke SystemInit() from the board specific armcm_main() code.
This gives the board code more control over board initialization.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename the linker script so the build does not have any conflicts with
the armcm_boot.d dependency file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a general build rule to precompile *.lds.S files to *.ld files.
Remove the custom rules in src/atsamd/Makefile and src/stm32/Makefile.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rework the spi_config commands so that bus configuration and shutdown
message configuration is done separately from the main "config_spi"
command. This makes the spi configuration more flexible. It's now
possible to use software spi without a CS pin. It's now possible to
define multiple SPI messages to send on a shutdown event.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Make it clear that the name of the constant being defined is a string.
When the value being defined is also a string, use a new
DECL_CONSTANT_STR() macro.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's rare to use all of a target's prerequisites in a recipe - replace
most cases with $< (the target's first prerequisite).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some of the samd21 chips have limited memory - change the code to
reduce the size of global variables.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use a local linker script instead of the linker script provided by
Atmel. This will allow Klipper to use dynamic memory allocation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Most samd boards have the crystal and it does improve the clock
accuracy, so default to enabling it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for using the internal clocks (with USB clock recovery
mode if available) on the SAMD21. Don't use the internal clock if the
external crystal is requested (instead use the PLL synced to the
external 32Khz signal).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for USB clock recovery mode if an external 32Khz crystal
is not in use. If using an external crystal, then don't use the
internal 48Mhz DFLL48Mhz clock (just use the PLLs synced to the
external 32Khz signal).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The SAMD51 ADC is only clocked on rising edges (vs both rising and
falling edges on the SAMD21) and it has a greater minimum frequency
than the SAMD21. So, increase the ADC clock.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the internal DWT timer is used for software timers, there is
no need to clock the peripherals at a higher clock speed. Clock all
peripherals at 48Mhz and simplify the clock generation code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Clearing the watchdog while it is in progress can cause bus stalls on
the SAMD21. It appears that clearing the watchdog on the SAMD51 can
cause lockups of the watchdog device.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor