Later addition of a F429 variant SKR2 was released. Changed btt-skr2 to btt-skr-2-f407 and added a new alias for btt-skr-2-f429
Signed-off-by: James Hartley <james@hartleyns.com>
After a G28 z-axis homing, there is a final z hop.
It was hoping to height z_hop as an absolute z height rather than relative.
If the z-axis home leaves the head at a z height higher than z_hop,
e.g. because you were using a probe to do z homing,
this meant that it was z hopping in the negative z direction, which
could result in crashing the toolhead.
Signed-off-by: Joshua Redstone <redstone@gmail.com>
Use a USB hex id to indicate that the device is already in bootloader
mode. This makes the rp2040 flashing code similar to the other
boards.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The rp2040 USB may not connect after a reset. Implementation the
recommended workaround.
Signed-off-by: Lasse Dalegaard <dalegaard@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
With recent changes, the extruder_stepper may be used for new
purposes, and synchronizing to the "extruder" motion queue at startup
may become a confusing default.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Deprecate SET_EXTRUDER_STEP_DISTANCE and SYNC_STEPPER_TO_EXTRUDER.
Recommend using SET_EXTRUDER_ROTATION_DISTANCE and
SYNC_EXTRUDER_MOTION.
Deprecate the extruder "shared_heater" option and reocmmend using
extruder_stepper config sections to obtain the same functionality.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It is preferable to program the tmc drivers with an irun (or cs)
setting near 31, as otherwise the driver may have reduced microstep
precision. It was possible for the driver to be programmed with
irun=16 or irun=17 when it could have been configured with irun=31
with vsense=1 instead. This would occur on tmc2130/tmc2208/tmc2209
drivers for values around 0.900 to 1.000 amps (when using a typical
sense_resistor settings of 0.110 Ohms).
Change the code to prefer using vsense=1 to avoid this issue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit 689231df changed the default step_pulse_duration to 100ns for
TMC drivers that are configured in UART/SPI mode, but it failed to
document that change in Config_Changes.md and Config_Reference.md.
Update those documents to reflect that change.
Update the code so that a user may specify a custom
step_pulse_duration even on TMC drivers that are configured in
UART/SPI mode. This may be useful for drivers that use a level
shifter on the step pin that requires more than a ~300ns to detect a
level change.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It seems the common "beta 3950" thermistors generally follow a
temperature table defined by the new "Generic 3950" definition. Using
a table that actually follows the "beta 3950" temperature curve is
generally less accurate. Deprecate the existing "NTC 100K beta 3950"
definition to avoid this common issue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Remove the STEP_DELAY Kconfig option and replace it with a per-stepper
step_pulse_duration printer.cfg config option.
The AVR code will continue to have optimized code to step and "unstep"
in the same function (which is automatically activated when the step
delay is 40 ticks or less). This change removes the Kconfig option
for single function step/unstep on 32bit processors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
A larger smooth_time results in a slower reaction time for the PID.
This increased delay can cause temperature oscillations with high
power heaters. Many boards produce good results without any
smoothing. So, it seems a smooth_time of 1 second is a better
default.
Reported by @ReXT3D.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Separate out the G-Code command handlers to a new ADXLCommandHelper()
class. This helps separate the sensing code from the user interface
code.
Deprecate the RATE parameter of the ACCELEROMETER_MEASURE command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Calculate the "homing position" using the endstop trigger time instead
of the position of the steppers.
This is in preparation for multi-mcu homing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The section-index plugin can cause some confusing navigation. Use the
simpler site navigation for now.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The atmega328pb has officially named these pins as PE2 and PE3, so use
that naming scheme instead of the previous Klipper invented names.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Document change in behavior of the controller_fan module.
Lookup heater objects in connect() event handler.
Return list of stepper names from stepper_enable.get_steppers().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Do not infer the sercom from the config section name, as that
prevents one from using SPI buses on multiple samd mcus.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The default pid_integral_max setting should be sufficient; it's not
necessary to complicate the documentation and config to support
customization.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The Jinja2 "set" directive is more flexible and easier to understand
than default_parameter_XXX parameters. Deprecate it and encourage
using "set" as a replacement.
This also deprecates direct access to parameters via parameter name in
a macro. Going forward, the `params` pseudo-variable must be used to
access a parameter.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow a larger velocity, accel, and square_corner_velocity than what
is specified in the config file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
None of the other TMC driver enable SFILT by default and it seems
enabling SFILT may not be ideal for sensorless homing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Check the status of all Trinamic stepper motor drivers once a second.
If the driver reports an error then invoke a shutdown. Also log any
serious warnings.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This reverts commit ac61f8b726.
Many temperature sensors are capitalized, so don't make this chaneg to
the bme280.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for automatically calculating the internal step_distance
from new config parameters - rotation_distance, microsteps,
full_steps_per_rotation, and gear_ratio.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add an 'mcu' option to the board_pins config and use that to specify
the name of the mcu to apply the aliases to. Support applying the
aliases to multiple mcus.
Add support for any number of options starting with an "aliases_"
prefix.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor