Removes a call to gcmd.respond_info which writes 'VARIABLE SAVED' to the
console every time the SAVE_VARIABLE command is called.
Signed-off-by: Andre LeBlanc <mapleleafmakers@gmail.com>
Raised from issue #5645, UTF-8 encoded symbols or other unexpected symbols on the UART raise an exception which causes klipper to stop. This change support UTF-8 encoded characters (from file names) as well as ignoring unexpected bytes.
Signed-off-by: Clifford Roche <clifford.roche@gmail.com>
An mcu device acting as an "mcu bridge" should only be reset after
other normal devices are reset - otherwise the bridge wont be able to
pass along the reset message to the downstream mcus.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Starting with nodeid 4 instead of nodeid 0 can reduce bitstuffing of
the id field in common configurations.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The `logging.basicConfig` does not reconfigure default logger.
This results in printing only warnings/errors to stderr
instead of also info (or debug).
This fixes the issue by setting log level on root logger.
Signed-off-by: Kamil Trzciński <ayufan@ayufan.eu>
Calling python functions can have high overhead. Inline the
twos_complement code in the _extract_samples() inner loop.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The MPU9250CommandHelper() class is nearly a duplicate of
ADXL345CommandHelper(). Rename ADXL345QueryHelper() to
AccelCommandHelper and remove user facing references to "adxl345". Use
it directly from mpu9250.py .
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The mpu9250.ClockSyncRegression() class is a duplicate of
adxl345.ClockSyncRegression(). Remove the duplicate copy and use the
code from adxl345.py .
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The MPU9250QueryHelper() class is a duplicate of ADXL345QueryHelper().
Rename ADXL345QueryHelper() to AccelQueryHelper() and use it directly
from mpu9250.py .
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Adds a save_config_pending_items to the status reported by
configfile reflecting the items and values that a future
SAVE_CONFIG would actually persist.
Signed-off-by: Kurt Haenen <kurt.haenen@gmail.com>
Just log an error on a fault.
Remove the host check for min/max temperature as the micro-controller
code already implements that check.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allows a limited number of DS18B20 read failures
before stopping the printer. This is designed to
tolerate spurious read errors, while still stopping
for serious issues.
The printer will stop when the sensor
fails to report a value five times in a row.
Implementation works as follows:
The MCU reports any read errors using a new "fault"
parameter in its answers.
The Python code tracks the number of errors
and triggers the shutdown. This paves the way for
more sophisticated error handling in the future,
as well as an example for other sensors to follow.
Signed-off-by: Lorenzo Pfeifer <Lorenzo.Pfeifer+github@googlemail.com>
Adding Klipper functionality to support cancelling objects while
printing.
This module keeps track of motion in and out of objects and adjusts
movements as needed. It also tracks object status and provides that to
clients.
The Klipper module is relatively simple, and only provides one piece of
the workflow. Moonraker already supports processing uploaded files to
insert the required gcode markers for cancelling objects, using
https://github.com/kageurufu/cancelobject-preprocessor. This library is
also available as an executable for use in slicers, and pip
installations also include the script as a callable.
Mainsail has integrated support, and code changes for Fluidd are
available. Support in other interfaces is planned, and we've spoken to
several other developers about integrating frontend support in their
projects.
Signed-off-by: Troy Jacobson <troy.d.jacobson@gmail.com>
Co-authored-by: Franklyn Tackitt <git@frank.af>
Co-authored-by: Eric Callahan <arksine.code@gmail.com>
Add PROBE and CHIP to TEST_RESONANCES
Since it's possible to specify more than one chip
in TEST_RESONANCES the CHIP parameter has been
renamed to CHIPS
Signed-off-by: Mikkel Schmidt <mikkel.schmidt@gmail.com>
Make sure whitespace isn't in the pin description. Also make sure an
alias doesn't map to an invalid pin.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Minor indentation and variable name changes.
Don't remove linebreaks from message_protocol_error lines.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The MCU protocol error message often confuses users, especially after getting bombarded with the config format error line. This PR tries to improve it and has the following goals:
- Put the technical error at the end to prevent confusion and avoid the immediate jump to help channels instead of continuing to read
- Inform the user first what the type of error is (In this case: MCU Protocol error) and not at the end of the long error message
- Give the users a clear instruction what to do (pretty much unchanged), but possibly more approachable because the user is not confused by the technical error anymore
- Shows the version numbers of Klipper separate from all MCU version numbers so that it is more obvious that this is the version of Klipper
- Separates the version numbers between outdated MCUs and up-to-date MCUs, so that it becomes obvious if a MCU flash failed because the MCU doesn't disappear from the outdated list
- Previously, when viewing the errors in a web frontend, additional line breaks made it extremely hard to read the message, sometimes with as little as one word on one line. The error messages are now formatted to not have rogue line breaks, improving readability.
Signed-off-by: Felicia Alexa Hummel <felicia@drachenkatze.org>
If the final update in a series of SET_LED update commands didn't
alter a color than the transmit would not occur - even if prior
commands did make color changes. Refactor the update code and fix.
Reported by @mstansberry.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This is most probably the result of a copy paste error. All vendor documentation for SI7021 (e.g. https://www.silabs.com/documents/public/data-sheets/Si7021-A20.pdf) points to 21 and it actually only works when adapted to 0x15 (=21).
Signed-off-by: Uli Wolf <github+klipper@wolf-u.li>
Added PCA9632 LED module support using software I2C from MCP4018
modulo drive the LED strip of a FlashForge Dreamer 3D printer.
Based on the PCA9533 module.
Signed-off-by: Ricardo Alcantara <ricardo@vulcanolabs.xyz>
Check that a SET_PRESSURE_ADVANCE without an explicit EXTRUDER
parameter isn't done after the user disables or reassociates the
extruder stepper motor (via SYNC_EXTRUDER_MOTION). Otherwise, it
could lead to very confusing results.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
With recent changes, the extruder_stepper may be used for new
purposes, and synchronizing to the "extruder" motion queue at startup
may become a confusing default.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Deprecate SET_EXTRUDER_STEP_DISTANCE and SYNC_STEPPER_TO_EXTRUDER.
Recommend using SET_EXTRUDER_ROTATION_DISTANCE and
SYNC_EXTRUDER_MOTION.
Deprecate the extruder "shared_heater" option and reocmmend using
extruder_stepper config sections to obtain the same functionality.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This command is a rename of SYNC_STEPPER_TO_EXTRUDER. This change is
in preparation for the removal of SYNC_STEPPER_TO_EXTRUDER.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support altering the extruder distance using the higher-level
rotation_distance. This is in preparation for removal of the
SET_EXTRUDER_STEP_DISTANCE command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The G2 / G3 command might be renamed using `gcode_macro` + `rename_existing`. This change allow detecting clockwise / anti-clockwise moves when the command gets renamed.
Signed-off-by: Nick Douma <n.douma@nekoconeko.nl>
Commit 7ef7bf60 broke the special handling for M117 commands that
start with a number or special character. Fix that support and extend
to M118 as well.
Also improve handling of commands not separated by a space (eg,
"M117HELLO").
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Refactor the extruder_stepper support so that it uses the
ExtruderStepper class defined in extruder.py.
Support the SYNC_STEPPER_TO_EXTRUDER command on steppers defined in
either extruder_stepper or extruder config sections.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Store the pressure_advance value in "struct extruder_stepper" instead
of in the trapq's "struct move". This makes it possible for multiple
stepper motors to have different pressure advance values while still
using the same trapq.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It is preferable to program the tmc drivers with an irun (or cs)
setting near 31, as otherwise the driver may have reduced microstep
precision. It was possible for the driver to be programmed with
irun=16 or irun=17 when it could have been configured with irun=31
with vsense=1 instead. This would occur on tmc2130/tmc2208/tmc2209
drivers for values around 0.900 to 1.000 amps (when using a typical
sense_resistor settings of 0.110 Ohms).
Change the code to prefer using vsense=1 to avoid this issue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Previously accidentally used 'default' state name instead of the
stated one ('PAUSE_STATE'). This might collide with user usage of the
SAVE_GCODE_STATE macro.
Signed-off-by: David Grundberg <individ@acc.umu.se>
MapleLeafMakers