848a78d1a5
docs: Fix typos ( #6032 )
...
Signed-off-by: Thijs Triemstra <info@collab.nl>
2023-02-20 11:06:25 -05:00
4b5d056421
stepper_enable: report status
...
Signed-off-by: Pedro Lamas <pedrolamas@gmail.com>
2023-02-13 12:16:17 -05:00
da8d4b0231
extruder: store currently sync'ed motion queue name
...
Signed-off-by: Pedro Lamas <pedrolamas@gmail.com>
2023-02-09 16:51:47 -05:00
ae9169c4c3
docs: Fix 'screw_thread' explanation in 'screws_tilt_adjust' section. ( #6039 )
...
Signed-off-by: Bassam Husain <bassam.husain@gmail.com>
2023-02-09 11:30:41 -05:00
5644481590
docs: Fixed wording in 'Bed_Mesh.md', fade_target section. ( #6025 )
...
Signed-off-by: Bassam Husain <bassam.husain@gmail.com>
2023-02-03 18:52:55 -05:00
fa78e6b8fb
screws_tilt_adjust: status result as dictionary
...
Signed-off-by: Pedro Lamas <pedrolamas@gmail.com>
2023-02-03 18:16:19 -05:00
e3253cb79e
docs: note change to bed_mesh profile behavior
...
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2023-02-01 11:07:16 -05:00
deed7f829a
docs: update RPi_microcontroller.md to systemd
...
Signed-off-by: Stefan Dej <meteyou@gmail.com>
2023-01-17 18:17:25 -05:00
4671cf2d0e
docs: Improve SET_PIN documentation in G-Codes.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2023-01-13 11:25:06 -05:00
cbc17a7cb6
docs: Note v0.11.0 release in Config_Changes.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2023-01-04 12:04:45 -05:00
3cd8a72e60
spi_flash: Add SKR2 F429 chip variant to spi_flash ( #5956 )
...
Later addition of a F429 variant SKR2 was released. Changed btt-skr2 to btt-skr-2-f407 and added a new alias for btt-skr-2-f429
Signed-off-by: James Hartley <james@hartleyns.com>
2023-01-04 12:01:28 -05:00
f57ff2c07e
docs: Fix typo in mpu9250 documentation
...
Adding MPU-6515, replacing MPU-9255 duplicate
Signed-off-by: Andrei Kozhevnikov <coderusinbox@gmail.com>
2022-12-30 22:28:59 -05:00
9b60daf62d
tmc: Configurable microstep lookup table ( #5920 )
...
Make all the microstep lookup table registers configurable via the
config file. It also loads the default values.
TMC220x and TMC2660 do not support this feature.
Signed-off-by: Alex Voinea <voinea.dragos.alexandru@gmail.com>
2022-12-21 21:23:23 -05:00
2a25733cd8
screws_tilt_adjust: Add get_status() method ( #5921 )
...
Signed-off-by: Christopher Meredith <chmeredith@gmail.com>
2022-12-17 11:39:25 -05:00
0c5c87d7c0
gcode_arcs: support XY, XZ and YZ planes
...
add G17, G18 and G19 commands to select arc planes
enhance G2/G3 to support arc moves in XY, XZ and YZ planes
Signed-off-by: Andrew Mirsky <andrew@mirsky.net>
2022-12-11 20:55:59 -05:00
e02b725602
docs: Note the release of v0.11.0
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2022-11-28 21:27:09 -05:00
817339a4ef
docs: Add a note about hardware independence to Features.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2022-11-28 21:14:11 -05:00
a9495d8e4f
docs: Updates to Features.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2022-11-28 20:59:31 -05:00
9727f00e50
docs: Minor update to safe_z_home change description in Config_Changes.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2022-11-22 18:57:15 -05:00
14eec15267
safe_z_home: Fix final z hop to use relative z coordinates ( #5879 )
...
After a G28 z-axis homing, there is a final z hop.
It was hoping to height z_hop as an absolute z height rather than relative.
If the z-axis home leaves the head at a z height higher than z_hop,
e.g. because you were using a probe to do z homing,
this meant that it was z hopping in the negative z direction, which
could result in crashing the toolhead.
Signed-off-by: Joshua Redstone <redstone@gmail.com>
2022-11-22 18:55:43 -05:00
d17ef95a3c
mpu9250: add MPU6500 ( #5767 )
...
Signed-off-by: Yifei Ding <yifeiding@protonmail.com>
2022-11-19 09:58:24 -05:00
d2a1dcbbf3
docs: Update Contacts.md with improved github issue tracker description
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2022-11-15 16:54:19 -05:00
d46c95b758
docs: Add a note about fixing underlying bugs in CONTRIBUTING.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2022-10-25 11:53:55 -04:00
a65e04aff7
docs: Add step rate benchmark for stm32h7
...
Signed-off-by: Konstantin Vogel <konstantin.vogel@gmx.net>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2022-10-21 20:33:28 -04:00
4b77f29c1b
atsamd: Add support CANbus on ATSAME5x chips
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2022-10-13 11:28:27 -04:00
b0ffb269d2
print_stats: add `SET_PRINT_STATS_INFO` G-Code for pass slicer variables to Klipper ( #5726 )
...
This adds a gcode command that can be used insight the slicer to pass the total layer count and current layer information.
Signed-off-by: Stefan Dej <meteyou@gmail.com>
2022-10-05 15:02:28 -04:00
34870d3e2a
z_thermal_adjust: Add Z thermal adjuster module ( #4157 )
...
Use a frame-coupled temperature probe to compensate for thermal
expansion in real-time.
Signed-off by: Robert Pazdzior <robertp@norbital.com>
2022-09-25 12:39:14 -04:00
8cdb2278d7
docs: Add an example corexy homing macro to TMC_Drivers.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2022-09-14 17:49:25 -04:00
79be427757
docs: Reword sensorless homing high sensitivity test in TMC_Drivers.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2022-09-14 17:13:48 -04:00
a530bf2421
docs: Add SDIO programming and split verification details to SDCard_Updates
...
Signed-off-by: Donna Whisnant <dewhisna@dewtronics.com>
2022-09-11 21:57:28 -04:00
9f8f3cd77d
fan: add enable_pin option ( #5732 )
...
Signed-off-by: Lasse Dalegaard <dalegaard@gmail.com>
2022-09-03 12:23:55 -04:00
ae6c16422f
mcp4018: Add SET_DIGIPOT command to mcp4018 implementation ( #5737 )
...
Added a SET_DIGIPOT command to the mcp4018 implementation.
Previously the mcp4018 was read only, and set at the time of
configuration. This allows you to change the value during a
print, which is needed for some older printers that need to
lower the stepper current during preheating.
Signed-off-by: Jake Bordens <jake@allaboutjake.com>
2022-09-02 10:30:06 -04:00
354915d2ad
kinematics: Add deltesian printers ( #5743 )
...
Initial push of the working deltesian kinematics after some successful tests.
Signed-off-by: Fabrice GALLET <tircown@gmail.com>
2022-09-01 15:56:31 -04:00
5d9ff75d02
extruder_stepper: Support configuring pressure advance from config
...
Also added status report for extruder_stepper objects with the
current pressure advance parameters values.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
2022-09-01 14:53:12 -04:00
f7e29b276e
docs: Update koconnor donation links
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2022-08-24 21:02:43 -04:00
6a91824486
delta: Added the possibility to get where the "cone shape" of the build volume starts from Macros ( #5662 )
...
Added the possibility to get where the "cone shape" of the build volume starts from Macros
Signed-off-by: Martin Malmqvist <Volcomosq@gmx.com>
2022-08-19 13:27:44 -04:00
dc012f8659
docs: Recommend allow-hotplug in CANBUS.md when using USB to canbus bridge
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2022-07-29 11:40:54 -04:00
2005d4dbf4
docs: Updates to CANBUS_protocol.md
...
Update the document with latest details.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2022-07-29 11:40:54 -04:00
b725d971db
bed_screws: report status
...
Signed-off-by: Pedro Lamas <pedrolamas@gmail.com>
2022-07-28 20:43:19 -04:00
c29e190696
docs: fixes typo on heater_bed
...
Signed-off-by: Pedro Lamas <pedrolamas@gmail.com>
2022-07-28 20:37:34 -04:00
282d1113e4
manual_probe: report status
...
Signed-off-by: Pedro Lamas <pedrolamas@gmail.com>
2022-07-21 22:03:31 -04:00
6be114d728
docs: fix rawparams example by truncating comments
...
Signed-off-by: Pedro Lamas <pedrolamas@gmail.com>
2022-07-19 12:48:16 -04:00
d91939c4bf
docs: Add BIGTREETECH to Sponsors.md file
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2022-07-16 23:17:30 -04:00
2f9fe49cb8
docs: Add a Sponsors.md file
...
Add a documentation page with information on how to support Klipper.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2022-07-16 10:48:10 -04:00
06022b305f
mkdocs-requirements: Force markdown==3.3.7
...
A new release of markdown (v3.4.1) breaks the website deployment
scripts. Force the existing version.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2022-07-16 10:43:53 -04:00
167736ad1c
respond: No forced spaces ( #5152 )
...
Signed-off-by: Adrian Joachim <adi.joachim12@gmail.com>
2022-06-30 13:56:35 -04:00
790ff4d8d7
usb_canbus: Initial support for USB to CAN bridge mode
...
Support a USB interface that shows up as a canbus adapter to linux.
Route both local and real canbus packets over that interface.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2022-06-27 10:50:23 -04:00
6ad6e39ad2
docs: add SET_DISPLAY_TEXT documentation
...
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2022-06-27 10:09:02 -04:00
ae17b66a88
docs: remove FAQ ToC ( #5585 )
...
Signed-off-by: Yifei Ding <yifeiding@protonmail.com>
2022-06-27 09:58:48 -04:00
52a8afba43
docs: Note mcu types with i2c_speed support in Config_Reference.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2022-06-20 12:58:05 -04:00
Thijs Triemstra